@@ -527,13 +527,6 @@ config WINBOND_W83627
legacy UART or other devices in the Winbond Super IO chips
on X86 platforms.
-config QCOM_GENI_SE
- bool "Qualcomm GENI Serial Engine Driver"
- depends on ARCH_SNAPDRAGON
- help
- The driver manages Generic Interface (GENI) firmware based
- Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper.
-
config QFW
bool
help
@@ -60,7 +60,6 @@ obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o
obj-$(CONFIG_P2SB) += p2sb-uclass.o
obj-$(CONFIG_PCA9551_LED) += pca9551_led.o
obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
-obj-$(CONFIG_QCOM_GENI_SE) += qcom-geni-se.o
ifdef CONFIG_QFW
obj-y += qfw.o
obj-$(CONFIG_QFW_PIO) += qfw_pio.o
deleted file mode 100644
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Qualcomm Generic Interface (GENI) Serial Engine (SE) Wrapper
- *
- * Copyright (C) 2023 Linaro Ltd. <vladimir.zapolskiy@linaro.org>
- */
-
-#include <common.h>
-#include <dm.h>
-#include <misc.h>
-#include <asm/io.h>
-
-static int geni_se_qup_read(struct udevice *dev, int offset,
- void *buf, int size)
-{
- fdt_addr_t base = dev_read_addr(dev);
-
- if (size != sizeof(u32))
- return -EINVAL;
-
- *(u32 *)buf = readl(base + offset);
-
- return size;
-}
-
-static struct misc_ops geni_se_qup_ops = {
- .read = geni_se_qup_read,
-};
-
-static const struct udevice_id geni_se_qup_ids[] = {
- { .compatible = "qcom,geni-se-qup" },
- {}
-};
-
-U_BOOT_DRIVER(geni_se_qup) = {
- .name = "geni_se_qup",
- .id = UCLASS_MISC,
- .of_match = geni_se_qup_ids,
- .ops = &geni_se_qup_ops,
- .flags = DM_FLAG_PRE_RELOC,
-};
@@ -957,8 +957,6 @@ config MSM_SERIAL
config MSM_GENI_SERIAL
bool "Qualcomm on-chip GENI UART"
- select MISC
- imply QCOM_GENI_SE
help
Support UART based on Generic Interface (GENI) Serial Engine (SE),
used on Qualcomm Snapdragon SoCs. Should support all qualcomm SOCs
@@ -486,12 +486,12 @@ static const struct dm_serial_ops msm_serial_ops = {
.setbrg = msm_serial_setbrg,
};
-static void geni_set_oversampling(struct udevice *dev)
+static int geni_set_oversampling(struct udevice *dev)
{
struct msm_serial_data *priv = dev_get_priv(dev);
- struct udevice *parent_dev = dev_get_parent(dev);
+ ofnode parent_node = ofnode_get_parent(dev_ofnode(dev));
u32 geni_se_version;
- int ret;
+ fdt_addr_t addr;
priv->oversampling = UART_OVERSAMPLING;
@@ -499,16 +499,22 @@ static void geni_set_oversampling(struct udevice *dev)
* It could happen that GENI SE IP is missing in the board's device
* tree or GENI UART node is a direct child of SoC device tree node.
*/
- if (device_get_uclass_id(parent_dev) != UCLASS_MISC)
- return;
+ if (!ofnode_device_is_compatible(parent_node, "qcom,geni-se-qup")) {
+ pr_err("%s: UART node must be a child of geniqup node\n",
+ __func__);
+ return -ENODEV;
+ }
- ret = misc_read(parent_dev, QUP_HW_VER_REG,
- &geni_se_version, sizeof(geni_se_version));
- if (ret != sizeof(geni_se_version))
- return;
+ /* Read the HW_VER register relative to the parents address space */
+ addr = ofnode_get_addr(parent_node);
+ geni_se_version = readl(addr + QUP_HW_VER_REG);
+
+ printf("geni_se_version: %x\n", geni_se_version);
if (geni_se_version >= QUP_SE_VERSION_2_5)
priv->oversampling /= 2;
+
+ return 0;
}
static inline void geni_serial_init(struct udevice *dev)
@@ -553,8 +559,11 @@ static inline void geni_serial_init(struct udevice *dev)
static int msm_serial_probe(struct udevice *dev)
{
struct msm_serial_data *priv = dev_get_priv(dev);
+ int ret;
- geni_set_oversampling(dev);
+ ret = geni_set_oversampling(dev);
+ if (ret < 0)
+ return ret;
/* No need to reinitialize the UART after relocation */
if (gd->flags & GD_FLG_RELOC)
commit 1b15483deb3f ("misc: add Qualcomm GENI SE QUP device driver") introduced support for platform-specific oversampling values, necessary to configure the UART clocks on all platforms at runtime. However it relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag, this is not done consistently during boot. Instead, take another approach by relying on ofnode_ helpers to read the serial engine base address and do the read directly. This fixes early UART on boards with a non-default oversampling rate. Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> --- drivers/misc/Kconfig | 7 ------- drivers/misc/Makefile | 1 - drivers/misc/qcom-geni-se.c | 41 ---------------------------------------- drivers/serial/Kconfig | 2 -- drivers/serial/serial_msm_geni.c | 29 ++++++++++++++++++---------- 5 files changed, 19 insertions(+), 61 deletions(-)