[v4,-next,4/4] spi: mockup: Add documentation

diff --git a/Documentation/spi/index.rst b/Documentation/spi/index.rst
index 06c34ea11bcf..a8f4f5cd0f09 100644
--- a/Documentation/spi/index.rst
+++ b/Documentation/spi/index.rst
@@ -13,6 +13,7 @@  Serial Peripheral Interface (SPI)
    pxa2xx
    spi-lm70llp
    spi-sc18is602
+   spi-mockup
 
 .. only::  subproject and html
 
diff --git a/Documentation/spi/spi-mockup.rst b/Documentation/spi/spi-mockup.rst
new file mode 100644
index 000000000000..a5b69ce83ad9
--- /dev/null
+++ b/Documentation/spi/spi-mockup.rst
@@ -0,0 +1,198 @@ 
+.. SPDX-License-Identifier: GPL-2.0
+
+==========
+spi-mockup
+==========
+
+Description
+===========
+
+This module is a very simple fake SPI controller driver. It implements
+a BPF based interface to mockup SPI device.
+
+No hardware is needed nor associated with this module. It will respond
+spi message by BPF program attached to spi_transfer_writeable tracepoint
+by reading from or writing BPF maps.
+
+The typical use-case is like this:
+        1. create the spi mockup controller;
+        2. load EBPF program as device's backend;
+        3. create target chip device to the spi mockup controller.
+
+Example
+=======
+
+This example show how to mock a MTD device by using spi-mockup driver.
+
+Compile your copy of the kernel source. Make sure to configure the spi-mockup
+and the target chip driver as a module.
+
+Register the spi mockup controller.
+
+::
+
+  $ mkdir /sys/kernel/config/spi-mockup/spi0
+
+  # configure the spi mockup controller attribute
+  $ echo 40000 > /sys/kernel/config/spi-mockup/spi0/min_speed
+  $ echo 25000000 > /sys/kernel/config/spi-mockup/spi0/max_speed
+  $ echo 0 > /sys/kernel/config/spi-mockup/spi0/flags
+  $ echo 8 > /sys/kernel/config/spi-mockup/spi0/num_cs
+
+  # enable the spi mockup controller
+  $ echo 1 > /sys/kernel/config/spi-mockup/spi0/live
+
+Write a BPF program as device's backup.
+
+::
+
+  #define MCHP23K256_CMD_WRITE_STATUS   0x01
+  #define MCHP23K256_CMD_WRITE          0x02
+  #define MCHP23K256_CMD_READ           0x03
+
+  #define CHIP_REGS_SIZE		0x20000
+
+  #define MAX_CMD_SIZE		        4
+
+  struct {
+	__uint(type, BPF_MAP_TYPE_ARRAY);
+	__uint(max_entries, CHIP_REGS_SIZE);
+	__type(key, __u32);
+	__type(value, __u8);
+  } regs_mchp23k256 SEC(".maps");
+
+  static unsigned int chip_reg = 0;
+
+  static int spi_transfer_read(struct spi_msg_ctx *msg, unsigned int len)
+  {
+	int i, key;
+	u8 *reg;
+
+	for (i = 0; i < len && i < sizeof(msg->data); i++) {
+		key = i + chip_reg;
+
+		reg = bpf_map_lookup_elem(&regs_mchp23k256, &key);
+		if (!reg) {
+			bpf_printk("key %d not exists", key);
+			return -EINVAL;
+		}
+
+		msg->data[i] = *reg;
+	}
+
+	return 0;
+  }
+
+  static int spi_transfer_write(struct spi_msg_ctx *msg, unsigned int len)
+  {
+	u8 opcode = msg->data[0], value;
+	int i, key;
+
+	switch (opcode) {
+	case MCHP23K256_CMD_READ:
+	case MCHP23K256_CMD_WRITE:
+		if (len < 2)
+			return -EINVAL;
+
+		chip_reg = 0;
+		for (i = 0; i < MAX_CMD_SIZE && i < len - 1; i++)
+			chip_reg = (chip_reg << 8) + msg->data[1 + i];
+
+		return 0;
+	case MCHP23K256_CMD_WRITE_STATUS:
+		// ignore write status
+		return 0;
+	default:
+		break;
+	}
+
+	for (i = 0; i < len && i < sizeof(msg->data); i++) {
+		value = msg->data[i];
+		key = chip_reg + i;
+
+		if (bpf_map_update_elem(&regs_mchp23k256, &key, &value,
+					BPF_EXIST)) {
+			bpf_printk("key %d not exists", key);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+  }
+
+  SEC("raw_tp.w/spi_transfer_writeable")
+  int BPF_PROG(mtd_mchp23k256, struct spi_msg_ctx *msg, u8 chip, unsigned int len)
+  {
+	int ret = 0;
+
+	if (msg->tx_nbits)
+		ret = spi_transfer_write(msg, len);
+	else if (msg->rx_nbits)
+		ret = spi_transfer_read(msg, len);
+
+	return ret;
+  }
+
+  char LICENSE[] SEC("license") = "GPL";
+
+Use bpftool to load the BPF program.
+
+::
+
+  $ bpftool prog load mtd-mchp23k256.o /sys/fs/bpf/mtd_mchp23k256 autoattach
+
+Create the mchp23k256 device, this is accomplished by executing the
+following command:
+
+::
+
+  $ mkdir /sys/kernel/config/spi-mockup/spi0/targets/mchp23k256
+  $ echo -n mchp23k256 > /sys/kernel/config/spi-mockup/spi0/targets/mchp23k256/device_id
+  $ echo 1 > /sys/kernel/config/spi-mockup/spi0/targets/mchp23k256/live
+
+
+Now, the mchp23k256 MTD device named /dev/mtd0 has been created successfully.
+
+::
+
+  $ ls /sys/bus/spi/devices/spi0.0/mtd/
+  mtd0  mtd0ro
+
+  $ cat /sys/class/mtd/mtd0/name
+  spi0.0
+
+  $ hexdump /dev/mtd0
+  0000000 0000 0000 0000 0000 0000 0000 0000 0000
+  *
+  0008000
+
+  $ echo aaaa > /dev/mtd0
+
+  $ hexdump /dev/mtd0
+  00000000  61 61 61 61 0a 00 00 00  00 00 00 00 00 00 00 00  |aaaa............|
+  00000010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
+  *
+  00008000
+
+  $ bpftool map update name regs_mchp23k256 key 0 0 0 0 value 0
+
+  $ hexdump /dev/mtd0
+  00000000  00 61 61 61 0a 00 00 00  00 00 00 00 00 00 00 00  |.aaa............|
+  00000010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
+  *
+  00008000
+
+
+Remove the mchp23k256 device by executing the following command:
+
+::
+
+  $ echo 0 > /sys/kernel/config/spi-mockup/spi0/targets/mchp23k256/live
+  $ rmdir /sys/kernel/config/spi-mockup/spi0/targets/mchp23k256
+
+Remove the spi mockup controller by executing the following command:
+
+::
+
+  $ echo 0 > /sys/kernel/config/spi-mockup/spi0/live
+  $ rmdir /sys/kernel/config/spi-mockup/spi0