@@ -249,7 +249,42 @@
reg = <0xC0000000 0x1000>;
interrupts = <22>;
clocks = <&auxosc>, <&pclk>;
- clock-names = "clcd", "apb_pclk";
+ clock-names = "clcdclk", "apb_pclk";
+
+ port {
+ /*
+ * The VGA connected is implemented with a
+ * THS8134A triple DAC that can be run in 24bit
+ * or 16bit RGB mode.
+ */
+ clcd_pads: endpoint {
+ remote-endpoint = <&clcd_panel>;
+ arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
+ };
+ };
+
+ panel {
+ compatible = "panel-dpi";
+
+ port {
+ clcd_panel: endpoint {
+ remote-endpoint = <&clcd_pads>;
+ };
+ };
+
+ /* Standard 640x480 VGA timings */
+ panel-timing {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ hsync-len = <96>;
+ vactive = <480>;
+ vback-porch = <33>;
+ vfront-porch = <10>;
+ vsync-len = <2>;
+ };
+ };
};
};
};
@@ -17,8 +17,6 @@
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/kmi.h>
-#include <linux/amba/clcd.h>
-#include <linux/platform_data/video-clcd-versatile.h>
#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <linux/irqchip.h>
@@ -42,8 +40,6 @@
/* Base address to the CP controller */
static void __iomem *intcp_con_base;
-#define INTCP_PA_CLCD_BASE 0xc0000000
-
/*
* Logical Physical
* f1000000 10000000 Core module registers
@@ -121,57 +117,6 @@ static struct mmci_platform_data mmc_data = {
.gpio_cd = -1,
};
-/*
- * CLCD support
- */
-/*
- * Ensure VGA is selected.
- */
-static void cp_clcd_enable(struct clcd_fb *fb)
-{
- struct fb_var_screeninfo *var = &fb->fb.var;
- u32 val = CM_CTRL_STATIC1 | CM_CTRL_STATIC2
- | CM_CTRL_LCDEN0 | CM_CTRL_LCDEN1;
-
- if (var->bits_per_pixel <= 8 ||
- (var->bits_per_pixel == 16 && var->green.length == 5))
- /* Pseudocolor, RGB555, BGR555 */
- val |= CM_CTRL_LCDMUXSEL_VGA555_TFT555;
- else if (fb->fb.var.bits_per_pixel <= 16)
- /* truecolor RGB565 */
- val |= CM_CTRL_LCDMUXSEL_VGA565_TFT555;
- else
- val = 0; /* no idea for this, don't trust the docs */
-
- cm_control(CM_CTRL_LCDMUXSEL_MASK|
- CM_CTRL_LCDEN0|
- CM_CTRL_LCDEN1|
- CM_CTRL_STATIC1|
- CM_CTRL_STATIC2|
- CM_CTRL_STATIC|
- CM_CTRL_n24BITEN, val);
-}
-
-static int cp_clcd_setup(struct clcd_fb *fb)
-{
- fb->panel = versatile_clcd_get_panel("VGA");
- if (!fb->panel)
- return -EINVAL;
-
- return versatile_clcd_setup_dma(fb, SZ_1M);
-}
-
-static struct clcd_board clcd_data = {
- .name = "Integrator/CP",
- .caps = CLCD_CAP_5551 | CLCD_CAP_RGB565 | CLCD_CAP_888,
- .check = clcdfb_check,
- .decode = clcdfb_decode,
- .enable = cp_clcd_enable,
- .setup = cp_clcd_setup,
- .mmap = versatile_clcd_mmap_dma,
- .remove = versatile_clcd_remove_dma,
-};
-
#define REFCOUNTER (__io_address(INTEGRATOR_HDR_BASE) + 0x28)
static u64 notrace intcp_read_sched_clock(void)
@@ -209,8 +154,6 @@ static struct of_dev_auxdata intcp_auxdata_lookup[] __initdata = {
"mmci", &mmc_data),
OF_DEV_AUXDATA("arm,primecell", INTEGRATOR_CP_AACI_BASE,
"aaci", &mmc_data),
- OF_DEV_AUXDATA("arm,primecell", INTCP_PA_CLCD_BASE,
- "clcd", &clcd_data),
{ /* sentinel */ },
};
The Integrator/CP CLCD VGA display can now be registered fully from the device tree. Delete the board file code and add the display definition to the DTS. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Actually include the hunk deleting the boardfile code as well. --- arch/arm/boot/dts/integratorcp.dts | 37 ++++++++++++++++++++- arch/arm/mach-integrator/integrator_cp.c | 57 -------------------------------- 2 files changed, 36 insertions(+), 58 deletions(-) -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel