@@ -11,8 +11,7 @@ maintainers:
description: |
This module is part of the DA9061/DA9062/DA9063. For more details about entire
- DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt
- For DA9063 see Documentation/devicetree/bindings/mfd/dlg,da9063.yaml
+ DA906{1,2,3} chips see Documentation/devicetree/bindings/mfd/dlg,da9063.yaml
This module provides the KEY_POWER event.
deleted file mode 100644
@@ -1,124 +0,0 @@
-* Dialog DA9062 Power Management Integrated Circuit (PMIC)
-
-Product information for the DA9062 and DA9061 devices can be found here:
-- https://www.dialog-semiconductor.com/products/da9062
-- https://www.dialog-semiconductor.com/products/da9061
-
-The DA9062 PMIC consists of:
-
-Device Supply Names Description
------- ------------ -----------
-da9062-regulator : : LDOs & BUCKs
-da9062-rtc : : Real-Time Clock
-da9062-onkey : : On Key
-da9062-watchdog : : Watchdog Timer
-da9062-thermal : : Thermal
-da9062-gpio : : GPIOs
-
-The DA9061 PMIC consists of:
-
-Device Supply Names Description
------- ------------ -----------
-da9062-regulator : : LDOs & BUCKs
-da9062-onkey : : On Key
-da9062-watchdog : : Watchdog Timer
-da9062-thermal : : Thermal
-
-======
-
-Required properties:
-
-- compatible : Should be
- "dlg,da9062" for DA9062
- "dlg,da9061" for DA9061
-- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
- modified to match the chip's OTP settings).
-
-Optional properties:
-
-- gpio-controller : Marks the device as a gpio controller.
-- #gpio-cells : Should be two. The first cell is the pin number and the
- second cell is used to specify the gpio polarity.
-
-See Documentation/devicetree/bindings/gpio/gpio.txt for further information on
-GPIO bindings.
-
-- interrupts : IRQ line information.
-- interrupt-controller
-
-See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
-further information on IRQ bindings.
-
-Sub-nodes:
-
-- regulators : This node defines the settings for the LDOs and BUCKs.
- The DA9062 regulators are bound using their names listed below:
-
- buck1 : BUCK_1
- buck2 : BUCK_2
- buck3 : BUCK_3
- buck4 : BUCK_4
- ldo1 : LDO_1
- ldo2 : LDO_2
- ldo3 : LDO_3
- ldo4 : LDO_4
-
- The DA9061 regulators are bound using their names listed below:
-
- buck1 : BUCK_1
- buck2 : BUCK_2
- buck3 : BUCK_3
- ldo1 : LDO_1
- ldo2 : LDO_2
- ldo3 : LDO_3
- ldo4 : LDO_4
-
- The component follows the standard regulator framework and the bindings
- details of individual regulator device can be found in:
- Documentation/devicetree/bindings/regulator/regulator.txt
-
- regulator-initial-mode may be specified for buck regulators using mode values
- from include/dt-bindings/regulator/dlg,da9063-regulator.h.
-
-- rtc : This node defines settings required for the Real-Time Clock associated
- with the DA9062. There are currently no entries in this binding, however
- compatible = "dlg,da9062-rtc" should be added if a node is created.
-
-- onkey : See ../input/dlg,da9062-onkey.yaml
-
-- watchdog: See ../watchdog/dlg,da9062-watchdog.yaml
-
-- thermal : See ../thermal/dlg,da9062-thermal.yaml
-
-Example:
-
- pmic0: da9062@58 {
- compatible = "dlg,da9062";
- reg = <0x58>;
- interrupt-parent = <&gpio6>;
- interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
-
- rtc {
- compatible = "dlg,da9062-rtc";
- };
-
- regulators {
- DA9062_BUCK1: buck1 {
- regulator-name = "BUCK1";
- regulator-min-microvolt = <300000>;
- regulator-max-microvolt = <1570000>;
- regulator-min-microamp = <500000>;
- regulator-max-microamp = <2000000>;
- regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
- regulator-boot-on;
- };
- DA9062_LDO1: ldo1 {
- regulator-name = "LDO_1";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <3600000>;
- regulator-boot-on;
- };
- };
- };
-
@@ -4,7 +4,7 @@
$id: http://devicetree.org/schemas/mfd/dlg,da9063.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: Dialog DA9063/DA9063L Power Management Integrated Circuit (PMIC)
+title: Dialog DA906{3L,3,2,1} Power Management Integrated Circuit (PMIC)
maintainers:
- Steve Twiss <stwiss.opensource@diasemi.com>
@@ -17,10 +17,17 @@ description: |
moment where all voltage monitors are disabled. Next, as da9063 only supports
UV *and* OV monitoring, both must be set to the same severity and value
(0: disable, 1: enable).
+ Product information for the DA906{3L,3,2,1} devices can be found here:
+ - https://www.dialog-semiconductor.com/products/da9063l
+ - https://www.dialog-semiconductor.com/products/da9063
+ - https://www.dialog-semiconductor.com/products/da9062
+ - https://www.dialog-semiconductor.com/products/da9061
properties:
compatible:
enum:
+ - dlg,da9061
+ - dlg,da9062
- dlg,da9063
- dlg,da9063l
@@ -35,6 +42,18 @@ properties:
"#interrupt-cells":
const: 2
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+
+ gpio:
+ type: object
+ additionalProperties: false
+ properties:
+ compatible:
+ const: dlg,da9062-gpio
+
onkey:
$ref: /schemas/input/dlg,da9062-onkey.yaml
@@ -42,7 +61,7 @@ properties:
type: object
additionalProperties: false
patternProperties:
- "^(ldo([1-9]|1[01])|bcore([1-2]|s-merged)|b(pro|mem|io|peri)|bmem-bio-merged)$":
+ "^(ldo([1-9]|1[01])|bcore([1-2]|s-merged)|b(pro|mem|io|peri)|bmem-bio-merged|buck[1-4])$":
$ref: /schemas/regulator/regulator.yaml
unevaluatedProperties: false
@@ -52,16 +71,85 @@ properties:
unevaluatedProperties: false
properties:
compatible:
- const: dlg,da9063-rtc
+ enum:
+ - dlg,da9062-rtc
+ - dlg,da9063-rtc
+
+ thermal:
+ $ref: /schemas/thermal/dlg,da9062-thermal.yaml
watchdog:
$ref: /schemas/watchdog/dlg,da9062-watchdog.yaml
+patternProperties:
+ "^(.+-hog(-[0-9]+)?)$":
+ type: object
+
+ required:
+ - gpio-hog
+
required:
- compatible
- reg
- - interrupts
- - interrupt-controller
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - dlg,da9063
+ - dlg,da9063l
+ then:
+ properties:
+ gpio-controller: false
+ "#gpio-cells": false
+ gpio: false
+ regulators:
+ patternProperties:
+ "^buck[1-4]$": false
+ thermal: false
+ required:
+ - interrupts
+ - interrupt-controller
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - dlg,da9062
+ then:
+ properties:
+ regulators:
+ patternProperties:
+ "^(ldo([5-9]|10|11)|bcore([1-2]|s-merged)|b(pro|mem|io|peri)|bmem-bio-merged)$": false
+ required:
+ - gpio
+ - onkey
+ - rtc
+ - thermal
+ - watchdog
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - dlg,da9061
+ then:
+ properties:
+ gpio-controller: false
+ "#gpio-cells": false
+ gpio: false
+ regulators:
+ patternProperties:
+ "^(ldo([5-9]|10|11)|bcore([1-2]|s-merged)|b(pro|mem|io|peri)|bmem-bio-merged|buck4)$": false
+ rtc: false
+ required:
+ - onkey
+ - thermal
+ - watchdog
additionalProperties: false
@@ -118,4 +206,121 @@ examples:
};
};
};
+
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/regulator/dlg,da9063-regulator.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pmic@58 {
+ compatible = "dlg,da9062";
+ reg = <0x58>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ sd0-pwr-sel-hog {
+ gpio-hog;
+ gpios = <1 0>;
+ input;
+ line-name = "SD0_PWR_SEL";
+ };
+
+ sd1-pwr-sel-hog {
+ gpio-hog;
+ gpios = <2 0>;
+ input;
+ line-name = "SD1_PWR_SEL";
+ };
+
+ sw-et0-en-hog {
+ gpio-hog;
+ gpios = <3 0>;
+ input;
+ line-name = "SW_ET0_EN#";
+ };
+
+ pmic-good-hog {
+ gpio-hog;
+ gpios = <4 0>;
+ output-high;
+ line-name = "PMIC_PGOOD";
+ };
+
+ gpio {
+ compatible = "dlg,da9062-gpio";
+ };
+
+ onkey {
+ compatible = "dlg,da9062-onkey";
+ };
+
+ regulators {
+ buck1 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+ regulator-always-on;
+ };
+ buck2 {
+ regulator-name = "vdd_soc";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+ regulator-always-on;
+ };
+ buck3 {
+ regulator-name = "vdd_ddr3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+ regulator-always-on;
+ };
+ buck4 {
+ regulator-name = "vdd_eth";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+ regulator-always-on;
+ };
+ ldo1 {
+ regulator-name = "vdd_snvs";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+ ldo2 {
+ regulator-name = "vdd_high";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+ ldo3 {
+ regulator-name = "vdd_eth_io";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ ldo4 {
+ regulator-name = "vdd_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
+
+ rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ thermal {
+ compatible = "dlg,da9062-thermal";
+ };
+
+ watchdog {
+ compatible = "dlg,da9062-watchdog";
+ dlg,use-sw-pm;
+ };
+ };
+ };
...
@@ -11,7 +11,7 @@ maintainers:
description: |
This module is part of the DA9061/DA9062. For more details about entire
- DA9062 and DA9061 chips see Documentation/devicetree/bindings/mfd/da9062.txt
+ DA906{1,2} chips see Documentation/devicetree/bindings/mfd/dlg,da9063.yaml
Junction temperature thermal module uses an interrupt signal to identify
high THERMAL_TRIP_HOT temperatures for the PMIC device.
Convert the da9062 PMIC device tree binding documentation to json-schema. Document the missing gpio child node for da9062. While at it, update description with link to product information and example. The missing child node with of_compatible defined in MFD_CELL_OF is causing the below warning message: da9062-gpio: Failed to locate of_node [id: -1] So, make all child nodes with of_compatible defined in struct mfd_cell as required property for da906{1,2} devices. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> --- v4->v5: * Updated commit description * Dropped unnecessary ref from gpio child node. * Added gpio-hog pattern property * Moved gpio-controller,gpio-cells above child nodes * Sorted compatible in rtc child node. * Dropped status from example. * Updated the example. v3->v4: * Split the thermal binding patch separate. * Updated the description. v2->v3: * Fixed bot errors related to MAINTAINERS entry, invalid doc references and thermal examples by merging patch#4. v2: * New patch --- .../bindings/input/dlg,da9062-onkey.yaml | 3 +- .../devicetree/bindings/mfd/da9062.txt | 124 ---------- .../devicetree/bindings/mfd/dlg,da9063.yaml | 215 +++++++++++++++++- .../bindings/thermal/dlg,da9062-thermal.yaml | 2 +- 4 files changed, 212 insertions(+), 132 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mfd/da9062.txt