@@ -27,6 +27,18 @@
regulator-boot-on;
};
+ vcc_1p8v: regulator-fixed@2 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1p8v";
+ regulator-type = "voltage";
+ startup-delay-us = <0>;
+ gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
gpio-keys {
compatible = "gpio-keys";
volume_up {
@@ -99,6 +111,7 @@
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
+ regulator-always-on;
};
/* msm_otg-HSUSB_3p3 */
@@ -133,13 +146,14 @@
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
bias-pull-down;
+ regulator-always-on;
};
/* pwm_power for backlight */
l17 {
regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3600000>;
- bias-pull-down;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
};
/* camera, qdsp6 */
@@ -184,6 +198,66 @@
};
};
+ mdp@5100000 {
+ status = "okay";
+ ports {
+ port@1 {
+ mdp_dsi1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: qcom,mdss_dsi@4700000 {
+ status = "okay";
+ vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+ vdd-supply = <&pm8921_l8>;
+ vddio-supply = <&pm8921_lvs7>;
+ avdd-supply = <&pm8921_l11>;
+ vcss-supply = <&ext_3p3v>;
+
+ panel@0 {
+ reg = <0>;
+ compatible = "jdi,lt070me05000";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dsi_panel_pinctrl>;
+
+ vddp-supply = <&pm8921_l17>;
+ dcdc_en-supply = <&pm8921_lvs7>;
+ vcc-supply = <&vcc_1p8v>;
+
+ reset-gpios = <&tlmm_pinmux 54 0>;
+ enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ ports {
+ port@0 {
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp_dsi1_out>;
+ };
+ };
+
+ port@1 {
+ dsi0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+
+ mdp_dsi_phy0: qcom,mdss_dsi_phy@4700200 {
+ status = "okay";
+ vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+ };
+
gsbi@16200000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
Tagging on to Archit's patchset here. Add DSI and panel nodes to get graphics up and running on the Nexus7. This still depends on the panel driver being present (currently under review) along with the rpmclk code. Feedback would be appreciated here! Cc: Archit Taneja <architt@codeaurora.org> Cc: vinay simha <vinaysimha@inforcecomputing.com> Cc: andy.gross@linaro.org Cc: robdclark@gmail.com Cc: linux-arm-msm@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: John Stultz <john.stultz@linaro.org> --- arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 78 +++++++++++++++++++++- 1 file changed, 76 insertions(+), 2 deletions(-) -- 1.9.1