@@ -77,9 +77,17 @@ port@1 {
reg = <1>;
pmic_glink_ss_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_ss>;
+ remote-endpoint = <&redriver_ss_out>;
};
};
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&wcd_usbss_sbu_mux>;
+ };
+ };
};
};
};
@@ -446,6 +454,70 @@ &gpi_dma1 {
status = "okay";
};
+&i2c3 {
+ status = "ok";
+
+ wcd_usbss: typec-mux@e {
+ compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+ reg = <0xe>;
+
+ vdd-supply = <&vreg_l15b_1p8>;
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+ mode-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wcd_usbss_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+ };
+};
+
+&i2c6 {
+ status = "ok";
+
+ typec-mux@1c {
+ compatible = "onnn,nb7vpq904m";
+ reg = <0x1c>;
+
+ vcc-supply = <&vreg_l15b_1p8>;
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ redriver_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ redriver_ss_in: endpoint {
+ data-lanes = <3 2 1 0>;
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+ };
+ };
+};
+
&ipa {
qcom,gsi-loader = "self";
memory-region = <&ipa_fw_mem>;
@@ -495,6 +567,15 @@ &mdss_dsi0_phy {
status = "okay";
};
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
&mdss_mdp {
status = "okay";
};
@@ -600,6 +681,11 @@ &pmk8550_rtc {
status = "okay";
};
+&qup_i2c3_data_clk {
+ /* Use internal I2C pull-up */
+ bias-pull-up = <2200>;
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -787,7 +873,7 @@ &usb_1_dwc3_hs {
};
&usb_1_dwc3_ss {
- remote-endpoint = <&pmic_glink_ss_in>;
+ remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
};
&usb_1_hsphy {
@@ -803,9 +889,23 @@ &usb_dp_qmpphy {
vdda-phy-supply = <&vreg_l3i_1p2>;
vdda-pll-supply = <&vreg_l3g_0p91>;
+ orientation-switch;
+
status = "okay";
};
+&usb_dp_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&redriver_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
&xo_board {
clock-frequency = <76800000>;
};
Add the necessary nodes to support the USB-C Altmode path by adding the following - WCD939x USBSS Mux I2C device - nb7vpq904m Redriver I2C device - Port/Endpoint graph links bettween PMIC-Glink, Mux, Redriver and USB PHY nodes. WCD939x USBSS port 2 Path to Codec will be added later when Audio support is added. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 104 +++++++++++++++++++++++++++++++- 1 file changed, 102 insertions(+), 2 deletions(-)