@@ -301,6 +301,87 @@
/* Added for reference of existence but should be handled by wait_for_completion already */
#define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3))
+#define QCA808X_MMD7_LED_GLOBAL 0x8073
+#define QCA808X_LED_BLINK_1 GENMASK(11, 6)
+#define QCA808X_LED_BLINK_2 GENMASK(5, 0)
+/* Values are the same for both BLINK_1 and BLINK_2 */
+#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3)
+#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
+#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
+#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
+#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
+#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
+#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
+#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
+#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
+#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0)
+#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
+#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
+#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
+#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
+#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
+#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
+#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
+#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
+
+#define QCA808X_MMD7_LED2_CTRL 0x8074
+#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075
+#define QCA808X_MMD7_LED1_CTRL 0x8076
+#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077
+#define QCA808X_MMD7_LED0_CTRL 0x8078
+#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2))
+
+/* LED hw control pattern is the same for every LED */
+#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0)
+#define QCA808X_LED_SPEED2500_ON BIT(15)
+#define QCA808X_LED_SPEED2500_BLINK BIT(14)
+/* Follow blink trigger even if duplex or speed condition doesn't match */
+#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13)
+#define QCA808X_LED_FULL_DUPLEX_ON BIT(12)
+#define QCA808X_LED_HALF_DUPLEX_ON BIT(11)
+#define QCA808X_LED_TX_BLINK BIT(10)
+#define QCA808X_LED_RX_BLINK BIT(9)
+#define QCA808X_LED_TX_ON_10MS BIT(8)
+#define QCA808X_LED_RX_ON_10MS BIT(7)
+#define QCA808X_LED_SPEED1000_ON BIT(6)
+#define QCA808X_LED_SPEED100_ON BIT(5)
+#define QCA808X_LED_SPEED10_ON BIT(4)
+#define QCA808X_LED_COLLISION_BLINK BIT(3)
+#define QCA808X_LED_SPEED1000_BLINK BIT(2)
+#define QCA808X_LED_SPEED100_BLINK BIT(1)
+#define QCA808X_LED_SPEED10_BLINK BIT(0)
+
+#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079
+#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2))
+
+/* LED force ctrl is the same for every LED
+ * No documentation exist for this, not even internal one
+ * with NDA as QCOM gives only info about configuring
+ * hw control pattern rules and doesn't indicate any way
+ * to force the LED to specific mode.
+ * These define comes from reverse and testing and maybe
+ * lack of some info or some info are not entirely correct.
+ * For the basic LED control and hw control these finding
+ * are enough to support LED control in all the required APIs.
+ *
+ * On doing some comparison with implementation with qca807x,
+ * it was found that it's 1:1 equal to it and confirms all the
+ * reverse done. It was also found further specification with the
+ * force mode and the blink modes.
+ */
+#define QCA808X_LED_FORCE_EN BIT(15)
+#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13)
+#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
+#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
+#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
+#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
+
+#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a
+/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
+ * LED to active high. It's not clear what BIT 3 and BIT 4 does.
+ */
+#define QCA808X_LED_ACTIVE_HIGH BIT(6)
+
/* QCA808X 1G chip type */
#define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d
#define QCA808X_PHY_CHIP_TYPE_1G BIT(0)
@@ -346,6 +427,7 @@ struct at803x_priv {
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
u64 stats[ARRAY_SIZE(qca83xx_hw_stats)];
+ int led_polarity_mode;
};
struct at803x_context {
@@ -706,6 +788,9 @@ static int at803x_probe(struct phy_device *phydev)
if (!priv)
return -ENOMEM;
+ /* Init LED polarity mode to -1 */
+ priv->led_polarity_mode = -1;
+
phydev->priv = priv;
ret = at803x_parse_dt(phydev);
@@ -2235,6 +2320,242 @@ static void qca808x_link_change_notify(struct phy_device *phydev)
phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
}
+static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+ u16 *offload_trigger)
+{
+ /* Parsing specific to netdev trigger */
+ if (test_bit(TRIGGER_NETDEV_TX, &rules))
+ *offload_trigger |= QCA808X_LED_TX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_RX, &rules))
+ *offload_trigger |= QCA808X_LED_RX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED10_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED100_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED1000_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED2500_ON;
+ if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+ if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+
+ if (rules && !*offload_trigger)
+ return -EOPNOTSUPP;
+
+ /* Enable BLINK_CHECK_BYPASS by default to make the LED
+ * blink even with duplex or speed mode not enabled.
+ */
+ *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 offload_trigger = 0;
+
+ if (index > 2)
+ return -EINVAL;
+
+ return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 reg, offload_trigger = 0;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+ if (ret)
+ return ret;
+
+ ret = qca808x_led_hw_control_enable(phydev, index);
+ if (ret)
+ return ret;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK,
+ offload_trigger);
+}
+
+static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return false;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+
+ return !(val & QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return -EINVAL;
+
+ /* Check if we have hw control enabled */
+ if (qca808x_led_hw_control_status(phydev, index))
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+ if (val & QCA808X_LED_TX_BLINK)
+ set_bit(TRIGGER_NETDEV_TX, rules);
+ if (val & QCA808X_LED_RX_BLINK)
+ set_bit(TRIGGER_NETDEV_RX, rules);
+ if (val & QCA808X_LED_SPEED10_ON)
+ set_bit(TRIGGER_NETDEV_LINK_10, rules);
+ if (val & QCA808X_LED_SPEED100_ON)
+ set_bit(TRIGGER_NETDEV_LINK_100, rules);
+ if (val & QCA808X_LED_SPEED1000_ON)
+ set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+ if (val & QCA808X_LED_SPEED2500_ON)
+ set_bit(TRIGGER_NETDEV_LINK_2500, rules);
+ if (val & QCA808X_LED_HALF_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+ if (val & QCA808X_LED_FULL_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK);
+}
+
+static int qca808x_led_brightness_set(struct phy_device *phydev,
+ u8 index, enum led_brightness value)
+{
+ u16 reg;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ if (!value) {
+ ret = qca808x_led_hw_control_reset(phydev, index);
+ if (ret)
+ return ret;
+ }
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
+ QCA808X_LED_FORCE_OFF);
+}
+
+static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ int ret;
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ /* Set blink to 50% off, 50% on at 4Hz by default */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
+ QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
+ QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
+ if (ret)
+ return ret;
+
+ /* We use BLINK_1 for normal blinking */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
+ if (ret)
+ return ret;
+
+ /* We set blink to 4Hz, aka 250ms */
+ *delay_on = 250 / 2;
+ *delay_off = 250 / 2;
+
+ return 0;
+}
+
+static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
+ unsigned long modes)
+{
+ struct at803x_priv *priv = phydev->priv;
+ bool active_low = false;
+ u32 mode;
+
+ for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+ switch (mode) {
+ case PHY_LED_ACTIVE_LOW:
+ active_low = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ /* PHY polarity is global and can't be set per LED.
+ * To detect this, check if last requested polarity mode
+ * match the new one.
+ */
+ if (priv->led_polarity_mode >= 0 &&
+ priv->led_polarity_mode != active_low) {
+ phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
+ return -EINVAL;
+ }
+
+ /* Save the last PHY polarity mode */
+ priv->led_polarity_mode = active_low;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN,
+ QCA808X_MMD7_LED_POLARITY_CTRL,
+ QCA808X_LED_ACTIVE_HIGH,
+ active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
+}
+
static struct phy_driver at803x_driver[] = {
{
/* Qualcomm Atheros AR8035 */
@@ -2411,6 +2732,12 @@ static struct phy_driver at803x_driver[] = {
.cable_test_start = qca808x_cable_test_start,
.cable_test_get_status = qca808x_cable_test_get_status,
.link_change_notify = qca808x_link_change_notify,
+ .led_brightness_set = qca808x_led_brightness_set,
+ .led_blink_set = qca808x_led_blink_set,
+ .led_hw_is_supported = qca808x_led_hw_is_supported,
+ .led_hw_control_set = qca808x_led_hw_control_set,
+ .led_hw_control_get = qca808x_led_hw_control_get,
+ .led_polarity_set = qca808x_led_polarity_set,
}, };
module_phy_driver(at803x_driver);