@@ -248,6 +248,7 @@ config SND_SOC_ALL_CODECS
imply SND_SOC_TAS2781_COMLIB
imply SND_SOC_TAS2781_FMWLIB
imply SND_SOC_TAS2781_I2C
+ imply SND_SOC_TAS2783
imply SND_SOC_TAS5086
imply SND_SOC_TAS571X
imply SND_SOC_TAS5720
@@ -1880,6 +1881,21 @@ config SND_SOC_TAS2781_I2C
algo coefficient setting, for one, two or even multiple TAS2781
chips.
+config SND_SOC_TAS2783
+ tristate "Texas Instruments TAS2783 speaker amplifier (sdw)"
+ depends on SOUNDWIRE
+ depends on EFI
+ select REGMAP
+ select REGMAP_SOUNDWIRE
+ select CRC32
+ select CRC32_SARWATE
+ help
+ Enable support for Texas Instruments TAS2783 Smart Amplifier
+ Digital input mono Class-D and DSP-inside audio power amplifiers.
+ TAS2783 supports the MIPI SoundWire v1.2 compatible interface
+ for audio and control data. At the end of calibrated data appends
+ the crc data with crc32_sarwate for error detection.
+
config SND_SOC_TAS5086
tristate "Texas Instruments TAS5086 speaker amplifier"
depends on I2C
@@ -287,6 +287,7 @@ snd-soc-tas2770-objs := tas2770.o
snd-soc-tas2781-comlib-objs := tas2781-comlib.o
snd-soc-tas2781-fmwlib-objs := tas2781-fmwlib.o
snd-soc-tas2781-i2c-objs := tas2781-i2c.o
+snd-soc-tas2783-objs := tas2783-sdw.o
snd-soc-tfa9879-objs := tfa9879.o
snd-soc-tfa989x-objs := tfa989x.o
snd-soc-tlv320adc3xxx-objs := tlv320adc3xxx.o
@@ -672,6 +673,7 @@ obj-$(CONFIG_SND_SOC_TAS2780) += snd-soc-tas2780.o
obj-$(CONFIG_SND_SOC_TAS2781_COMLIB) += snd-soc-tas2781-comlib.o
obj-$(CONFIG_SND_SOC_TAS2781_FMWLIB) += snd-soc-tas2781-fmwlib.o
obj-$(CONFIG_SND_SOC_TAS2781_I2C) += snd-soc-tas2781-i2c.o
+obj-$(CONFIG_SND_SOC_TAS2783) += snd-soc-tas2783.o
obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o
obj-$(CONFIG_SND_SOC_TAS571X) += snd-soc-tas571x.o
obj-$(CONFIG_SND_SOC_TAS5720) += snd-soc-tas5720.o
new file mode 100644
@@ -0,0 +1,892 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// ALSA SoC Texas Instruments TAS2783 Audio Smart Amplifier
+//
+// Copyright (C) 2023 - 2024 Texas Instruments Incorporated
+// https://www.ti.com
+//
+// Author: Baojun Xu <baojun.xu@ti.com>
+// Kevin Lu <kevin-lu@ti.com>
+// Shenghao Ding <shenghao-ding@ti.com>
+//
+
+#include <asm/unaligned.h>
+#include <linux/acpi.h>
+#include <linux/crc32.h>
+#include <linux/efi.h>
+#include <linux/err.h>
+#include <linux/firmware.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_registers.h>
+#include <linux/soundwire/sdw_type.h>
+#include <sound/pcm_params.h>
+#include <sound/sdw.h>
+#include <sound/soc.h>
+#include <sound/tlv.h>
+
+#include <sound/tas2781-tlv.h>
+#include "tas2783.h"
+
+struct calibdatav2_info {
+ unsigned int number_of_devices;
+ unsigned int crc32_pos;
+ unsigned int byt_sz;
+ unsigned int *cali_data;
+};
+
+static const unsigned int tas2783_cali_reg[] = {
+ TAS2783_CALIBRATION_RE, /* Resistance */
+ TAS2783_CALIBRATION_RE_LOW, /* Low limitation of RE */
+ TAS2783_CALIBRATION_INV_RE, /* Reciprocal of RE */
+ TAS2783_CALIBRATION_POW, /* RMS Power */
+ TAS2783_CALIBRATION_TLIMIT /* Temperature limitation */
+};
+
+static bool tas2783_readable_register(struct device *dev,
+ unsigned int reg)
+{
+ switch (reg) {
+ case 0x8000 ... 0x807F:
+ case SDW_SDCA_CTL(TAS2783_FUNC_TYPE_SMART_AMP, TAS2783_SDCA_ENT_FU21,
+ TAS2783_SDCA_CTL_FU_MUTE, 0):
+ case SDW_SDCA_CTL(TAS2783_FUNC_TYPE_SMART_AMP, TAS2783_SDCA_ENT_FU21,
+ TAS2783_SDCA_CTL_FU_VOLUME, 0):
+ case SDW_SDCA_CTL(TAS2783_FUNC_TYPE_SMART_AMP, TAS2783_SDCA_ENT_FU23,
+ TAS2783_SDCA_CTL_FU_MUTE, 0):
+ return true;
+ default:
+ return false;
+ }
+}
+
+static bool tas2783_volatile_register(struct device *dev,
+ unsigned int reg)
+{
+ switch (reg) {
+ /*
+ * Only software reset register was volatiled.
+ * Bit is self clearing.
+ * 0b = Don't reset
+ * 1b = reset
+ */
+ case 0x8001:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct regmap_config tasdevice_regmap = {
+ .reg_bits = 32,
+ .val_bits = 8,
+ .readable_reg = tas2783_readable_register,
+ .volatile_reg = tas2783_volatile_register,
+ .max_register = 0x44ffffff,
+ .cache_type = REGCACHE_MAPLE,
+ .use_single_read = true,
+ .use_single_write = true,
+};
+
+static const struct snd_kcontrol_new tas2783_snd_controls[] = {
+ SOC_SINGLE_RANGE_TLV("Digital Volume", TAS2783_DVC_LVL,
+ 0, 0, 200, 1, dvc_tlv),
+ SOC_SINGLE_SX_TLV("Amp Gain Volume", TAS2783_AMP_LEVEL,
+ 1, 0, 20, amp_vol_tlv),
+};
+
+/*
+ * Load the calibration data, including speaker impedance, f0, etc.
+ * Calibration is done by the manufacturer in the factory. The calibration
+ * data are used by the algorithm for calculating the speaker temperature,
+ * speaker membrane excursion and f0 in real time during playback.
+ * The DSP will work with default data values if calibrated data are
+ * missing or are invalid.
+ * Layout of calibrated Data V1 in UEFI(total 256 bytes):
+ * Calibrated Data of Dev 0(unique_id offset 0) (20 bytes)
+ * Calibrated Data of Dev 1(unique_id offset 1) (20 bytes)
+ * Calibrated Data of Dev 2(unique_id offset 2) (20 bytes)
+ * Calibrated Data of Dev 3(unique_id offset 3) (20 bytes)
+ * Calibrated Data of Dev 4(unique_id offset 4) (20 bytes)
+ * Calibrated Data of Dev 5(unique_id offset 5) (20 bytes)
+ * Calibrated Data of Dev 6(unique_id offset 6) (20 bytes)
+ * Calibrated Data of Dev 7(unique_id offset 7) (20 bytes)
+ * TimeStamp of Calibration (4 bytes)
+ * CRC (4 bytes)
+ * Reserved (88 bytes)
+ */
+static void tas2783_apply_calibv1(struct tasdevice_priv *tas_dev,
+ unsigned int *cali_data)
+{
+ struct regmap *map = tas_dev->regmap;
+ u8 *cali_start;
+ u16 offset;
+ int ret;
+
+ if (!tas_dev->sdw_peripheral) {
+ dev_err(tas_dev->dev, "%s: peripheral doesn't exist.\n",
+ __func__);
+ return;
+ }
+
+ offset = tas_dev->sdw_peripheral->id.unique_id -
+ TAS2783_UNIQUE_ID_BASE;
+ if (offset >= TAS2783_MAX_DEV_NUM) {
+ dev_err(tas_dev->dev, "%s: offset(%u) is out of range.\n",
+ __func__, offset);
+ return;
+ }
+
+ /*
+ * The area saving tas2783 calibrated data is specified by its
+ * unique_id offset. cali_start is the first address of current
+ * tas2783's calibrated data.
+ */
+ cali_start = (u8 *)(cali_data + offset * sizeof(tas2783_cali_reg));
+ for (int i = 0; i < ARRAY_SIZE(tas2783_cali_reg); i++) {
+ ret = regmap_bulk_write(map, tas2783_cali_reg[i],
+ &cali_start[4 * i], 4);
+ if (ret) {
+ dev_err(tas_dev->dev, "%s: Cali failed %x:%d\n",
+ __func__, tas2783_cali_reg[i], ret);
+ break;
+ }
+ }
+}
+
+/*
+ * New features were added in calibrated Data V2:
+ * 1. Added some the fields to store the link_id and uniqie_id for
+ * multi-link solutions
+ * 2. Support flexible number of devices instead of fixed one in V1.
+ * Layout of calibrated data V2 in UEFI(total 256 bytes):
+ * ChipID (2783, 4 bytes)
+ * Device-Sum (4 bytes)
+ * TimeStamp of Calibration (4 bytes)
+ * for (i = 0; i < Device-Sum; i++) {
+ * Device #i index_info () {
+ * SDW link id (2bytes)
+ * SDW unique_id (2bytes)
+ * }
+ * Calibrated Data of Device #i (20 bytes)
+ * }
+ * CRC (4 bytes)
+ * Reserved (the rest)
+ */
+static void tas2783_apply_calibv2(struct tasdevice_priv *tas_dev,
+ unsigned int *tmp_val)
+{
+ const unsigned int arr_size = ARRAY_SIZE(tas2783_cali_reg);
+ const struct calibdatav2_info calib_info = {
+ .number_of_devices = tmp_val[1],
+ .crc32_pos = 3 + tmp_val[1] * 6,
+ .byt_sz = 12 + tmp_val[1] * 24,
+ .cali_data = &tmp_val[3]
+ };
+ struct regmap *map = tas_dev->regmap;
+ unsigned int i, j, k, crc;
+ u8 *cali_start;
+ u16 dev_indx;
+ int ret;
+
+ if (!tas_dev->sdw_peripheral) {
+ dev_err(tas_dev->dev, "%s: peripheral doesn't exist.\n",
+ __func__);
+ return;
+ }
+
+ if (calib_info.number_of_devices > TAS2783_MAX_DEV_NUM ||
+ calib_info.number_of_devices == 0) {
+ dev_info(tas_dev->dev,
+ "using default calibration data, wrong data in EFI.");
+ return;
+ }
+ crc = crc32(~0, tmp_val, calib_info.byt_sz) ^ ~0;
+ if (crc != tmp_val[calib_info.crc32_pos]) {
+ dev_info(tas_dev->dev,
+ "using default calibration data, crc not match.");
+ return;
+ }
+
+ dev_indx = tas_dev->sdw_peripheral->bus->link_id |
+ tas_dev->sdw_peripheral->id.unique_id << 16;
+
+ for (i = 0; i < calib_info.number_of_devices; i++) {
+ k = i * (arr_size + 1);
+
+ if (dev_indx != calib_info.cali_data[k])
+ continue;
+
+ /* +1: skip 4 byte dev-indx info */
+ cali_start = (u8 *)&calib_info.cali_data[k + 1];
+
+ for (j = 0; j < arr_size; j++) {
+ k = 4 * j;
+ ret = regmap_bulk_write(map, tas2783_cali_reg[j],
+ &cali_start[k], 4);
+ if (ret) {
+ dev_err(tas_dev->dev,
+ "%s: Cali data writing failed %x:%d\n",
+ __func__, tas2783_cali_reg[j], ret);
+ break;
+ }
+ }
+ return;
+ }
+}
+
+static void tas2783_calibration(struct tasdevice_priv *tas_dev)
+{
+ efi_guid_t efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc,
+ 0x09, 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92);
+ static efi_char16_t efi_name[] = L"CALI_DATA";
+ struct calibration_data cali_data;
+ unsigned int *tmp_val;
+ unsigned int crc;
+ efi_status_t status;
+
+ cali_data.total_sz = 0;
+
+ status = efi.get_variable(efi_name, &efi_guid, NULL,
+ &cali_data.total_sz, NULL);
+ if (status == EFI_BUFFER_TOO_SMALL
+ && cali_data.total_sz < TAS2783_MAX_CALIDATA_SIZE) {
+ status = efi.get_variable(efi_name, &efi_guid, NULL,
+ &cali_data.total_sz,
+ cali_data.data);
+ dev_dbg(tas_dev->dev, "%s: cali get %lx bytes result:%ld\n",
+ __func__, cali_data.total_sz, status);
+ }
+ if (status != 0) {
+ /* Failed got calibration data from EFI. */
+ dev_dbg(tas_dev->dev, "No calibration data in UEFI.");
+ return;
+ }
+
+ tmp_val = (unsigned int *)cali_data.data;
+
+ /* Check Calibrated Data V1 */
+ crc = crc32(~0, cali_data.data, TAS2783_CALIDATAV1_BYTE_SIZE) ^ ~0;
+ if (crc == tmp_val[TAS2783_CALIDATAV1_CRC32_INDX]) {
+ /* Date and time of when calibration was done. */
+ tas2783_apply_calibv1(tas_dev, tmp_val);
+ return;
+ }
+
+ /* Check Calibrated Data V2 */
+ if (tmp_val[0] != 2783) {
+ dev_err(tas_dev->dev, "No tas2783 calibration data\n");
+ return;
+ }
+
+ tas2783_apply_calibv2(tas_dev, tmp_val);
+}
+
+static void tasdevice_dspfw_ready(const struct firmware *fmw,
+ void *context)
+{
+ struct tasdevice_priv *tas_dev = (struct tasdevice_priv *) context;
+ struct regmap *map = tas_dev->regmap;
+ struct tas2783_firmware_node *p;
+ unsigned char *buf;
+ int fw_node_sz = sizeof(struct tas2783_firmware_node);
+ int img_sz, ret;
+ int offset = 0;
+
+ if (!fmw || !fmw->data) {
+ dev_warn(tas_dev->dev,
+ "%s: failed to read fw, work in bypass-dsp mode.\n",
+ __func__);
+ return;
+ }
+ buf = (unsigned char *)fmw->data;
+
+ img_sz = get_unaligned_le32(&buf[offset]);
+ offset += sizeof(img_sz);
+ if (img_sz != fmw->size) {
+ dev_warn(tas_dev->dev, "%s: size not matching, %d %u.",
+ __func__, (int)fmw->size, img_sz);
+ return;
+ }
+
+ while (offset < img_sz) {
+ p = (struct tas2783_firmware_node *)(buf + offset);
+ if (p->length > 1)
+ ret = regmap_bulk_write(map, p->download_addr,
+ buf + offset + fw_node_sz, p->length);
+ else
+ ret = regmap_write(map, p->download_addr,
+ *(buf + offset + fw_node_sz));
+
+ if (ret != 0) {
+ dev_dbg(tas_dev->dev,
+ "%s: load FW fail: %d, work in bypass.\n",
+ __func__, ret);
+ return;
+ }
+ offset += fw_node_sz + p->length;
+ }
+
+ tas2783_calibration(tas_dev);
+}
+
+static const struct snd_soc_dapm_widget tasdevice_dapm_widgets[] = {
+ SND_SOC_DAPM_AIF_IN("ASI", "ASI Playback", 0, SND_SOC_NOPM, 0, 0),
+ SND_SOC_DAPM_AIF_OUT("ASI OUT", "ASI Capture", 0, SND_SOC_NOPM, 0, 0),
+ SND_SOC_DAPM_OUTPUT("OUT"),
+ SND_SOC_DAPM_INPUT("DMIC"),
+};
+
+static const struct snd_soc_dapm_route tasdevice_audio_map[] = {
+ {"OUT", NULL, "ASI"},
+ {"ASI OUT", NULL, "DMIC"},
+};
+
+static int tasdevice_set_sdw_stream(struct snd_soc_dai *dai,
+ void *sdw_stream, int direction)
+{
+ snd_soc_dai_dma_data_set(dai, direction, sdw_stream);
+
+ return 0;
+}
+
+static void tasdevice_sdw_shutdown(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ snd_soc_dai_set_dma_data(dai, substream, NULL);
+}
+
+static int tasdevice_sdw_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct tasdevice_priv *tas_priv =
+ snd_soc_component_get_drvdata(component);
+ struct sdw_stream_config stream_config = {0};
+ struct sdw_port_config port_config = {0};
+ struct sdw_stream_runtime *sdw_stream;
+ int ret;
+
+ dev_dbg(dai->dev, "%s: dai_name %s", __func__, dai->name);
+ sdw_stream = snd_soc_dai_get_dma_data(dai, substream);
+
+ if (!sdw_stream)
+ return -EINVAL;
+
+ if (!tas_priv->sdw_peripheral)
+ return -EINVAL;
+
+ /* SoundWire specific configuration */
+ snd_sdw_params_to_config(substream, params,
+ &stream_config, &port_config);
+
+ /* port 1 for playback */
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ port_config.num = 1;
+ else
+ port_config.num = 2;
+
+ ret = sdw_stream_add_slave(tas_priv->sdw_peripheral,
+ &stream_config, &port_config, 1, sdw_stream);
+ if (ret) {
+ dev_err(dai->dev, "%s: Unable to configure port\n", __func__);
+ return ret;
+ }
+
+ dev_dbg(dai->dev, "%s: format: %i rate: %i\n", __func__,
+ params_format(params), params_rate(params));
+
+ return 0;
+}
+
+static int tasdevice_sdw_pcm_hw_free(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_component *component = dai->component;
+ struct tasdevice_priv *tas_priv =
+ snd_soc_component_get_drvdata(component);
+ struct sdw_stream_runtime *sdw_stream =
+ snd_soc_dai_get_dma_data(dai, substream);
+
+ if (!tas_priv->sdw_peripheral)
+ return -EINVAL;
+
+ sdw_stream_remove_slave(tas_priv->sdw_peripheral, sdw_stream);
+
+ return 0;
+}
+
+/* Capture stream is the echo ref data for voice mode.*/
+static int tasdevice_enable_echo_ref(struct tasdevice_priv *tas_dev,
+ int mute)
+{
+ struct regmap *map = tas_dev->regmap;
+ unsigned int val;
+ int ret;
+
+ if (mute)
+ val = TAS2783_REG_AEF_INACTIVE;
+ else
+ val = TAS2783_REG_AEF_ACTIVE;
+
+ ret = regmap_update_bits(map, TAS2873_REG_PWR_CTRL,
+ TAS2783_REG_AEF_MASK, TAS2783_REG_AEF_INACTIVE);
+ if (ret)
+ dev_err(tas_dev->dev, "%s: Disable AEF failed.\n", __func__);
+
+ return ret;
+}
+
+static int tasdevice_playback(struct tasdevice_priv *tas_dev, int mute)
+{
+ struct regmap *map = tas_dev->regmap;
+ int ret;
+
+ if (mute) {
+ /* FU23 mute (0x40400108) */
+ ret = regmap_write(map,
+ SDW_SDCA_CTL(TAS2783_FUNC_TYPE_SMART_AMP,
+ TAS2783_SDCA_ENT_FU23,
+ TAS2783_SDCA_CTL_FU_MUTE, 0), 1);
+ if (ret) {
+ dev_err(tas_dev->dev, "%s: FU23 mute failed.\n",
+ __func__);
+ goto out;
+ }
+
+ ret = regmap_update_bits(map, TAS2873_REG_PWR_CTRL,
+ TAS2783_REG_PWR_MODE_MASK |
+ TAS2783_REG_AEF_MASK,
+ TAS2783_REG_PWR_MODE_ACTIVE |
+ TAS2783_REG_PWR_MODE_SW_PWD);
+ if (ret) {
+ dev_err(tas_dev->dev, "%s: shutdown failed.\n",
+ __func__);
+ }
+ } else {
+ /* FU23 Unmute, 0x40400108. */
+ ret = regmap_write(map,
+ SDW_SDCA_CTL(TAS2783_FUNC_TYPE_SMART_AMP,
+ TAS2783_SDCA_ENT_FU23,
+ TAS2783_SDCA_CTL_FU_MUTE, 0), 0);
+ if (ret) {
+ dev_err(tas_dev->dev,
+ "%s: FU23 Unmute failed.\n", __func__);
+ goto out;
+ }
+ ret = regmap_update_bits(map, TAS2873_REG_PWR_CTRL,
+ TAS2783_REG_PWR_MODE_MASK,
+ TAS2783_REG_PWR_MODE_ACTIVE);
+ if (ret) {
+ dev_err(tas_dev->dev,
+ "%s: PWR Unmute failed.\n", __func__);
+ }
+ }
+out:
+ return ret;
+}
+
+static int tasdevice_mute(struct snd_soc_dai *dai, int mute,
+ int direction)
+{
+ struct snd_soc_component *component = dai->component;
+ struct tasdevice_priv *tas_dev =
+ snd_soc_component_get_drvdata(component);
+
+ int ret;
+
+ dev_dbg(tas_dev->dev, "%s: %d.\n", __func__, mute);
+
+ if (direction == SNDRV_PCM_STREAM_CAPTURE)
+ ret = tasdevice_enable_echo_ref(tas_dev, mute);
+ else
+ ret = tasdevice_playback(tas_dev, mute);
+
+ if (ret)
+ dev_err(tas_dev->dev, "Mute or unmute %d failed %d.\n",
+ mute, ret);
+
+ return ret;
+}
+
+static const struct snd_soc_dai_ops tasdevice_dai_ops = {
+ .mute_stream = tasdevice_mute,
+ .hw_params = tasdevice_sdw_hw_params,
+ .hw_free = tasdevice_sdw_pcm_hw_free,
+ .set_stream = tasdevice_set_sdw_stream,
+ .shutdown = tasdevice_sdw_shutdown,
+};
+
+static struct snd_soc_dai_driver tasdevice_dai_driver[] = {
+ {
+ .name = "tas2783-codec",
+ .id = 0,
+ .playback = {
+ .stream_name = "Playback",
+ .channels_min = 1,
+ .channels_max = 4,
+ .rates = TAS2783_DEVICE_RATES,
+ .formats = TAS2783_DEVICE_FORMATS,
+ },
+ .capture = {
+ .stream_name = "Capture",
+ .channels_min = 1,
+ .channels_max = 4,
+ .rates = TAS2783_DEVICE_RATES,
+ .formats = TAS2783_DEVICE_FORMATS,
+ },
+ .ops = &tasdevice_dai_ops,
+ .symmetric_rate = 1,
+ },
+};
+
+static int tasdevice_comp_probe(struct snd_soc_component *comp)
+{
+ struct tasdevice_priv *tas_dev = snd_soc_component_get_drvdata(comp);
+ unsigned char dspfw_binaryname[TAS2783_DSPFW_FILENAME_LEN];
+ acpi_handle handle = ACPI_HANDLE(tas_dev->dev);
+ const struct firmware *fw_entry = NULL;
+ const char *sub = NULL;
+ int ret;
+
+ if (handle) {
+ sub = acpi_get_subsystem_id(handle);
+ if (IS_ERR(sub))
+ sub = NULL;
+ }
+
+ /*
+ * Each tas2783 in the system has its own dspfw.
+ */
+ if (comp->name_prefix) {
+ /*
+ * name_prefix.bin stores the dsp firmware including speaker
+ * protection algorithm, audio acoustic algorithm, speaker
+ * characters and algorithm params, it must be copied into
+ * firmware folder.
+ */
+ scnprintf(dspfw_binaryname, TAS2783_DSPFW_FILENAME_LEN,
+ "%s-tas2783.bin", comp->name_prefix);
+ } else {
+ /* Compatible with the previous naming rule */
+ if (sub) {
+ /*
+ * subsys_id-link_id[0,1,...,N]-unique_id
+ * [0x8,...,0xf].bin stores the dsp firmware including
+ * speaker protection algorithm, audio acoustic
+ * algorithm, speaker characters and algorithm params,
+ * it must be copied into firmware folder.
+ */
+ scnprintf(dspfw_binaryname, TAS2783_DSPFW_FILENAME_LEN,
+ "%s-%d-0x%x.bin", sub,
+ tas_dev->sdw_peripheral->bus->link_id,
+ tas_dev->sdw_peripheral->id.unique_id);
+ } else {
+ /*
+ * tas2783-link_id[0,1,...,N]-unique_id
+ * [0x8,...,0xf].bin stores the dsp firmware including
+ * speaker protection algorithm, audio acoustic
+ * algorithm, speaker characters and algorithm params,
+ * it must be copied into firmware folder.
+ */
+ scnprintf(dspfw_binaryname, TAS2783_DSPFW_FILENAME_LEN,
+ "tas2783-%d-0x%x.bin",
+ tas_dev->sdw_peripheral->bus->link_id,
+ tas_dev->sdw_peripheral->id.unique_id);
+ }
+ }
+
+ ret = request_firmware(&fw_entry, dspfw_binaryname, tas_dev->dev);
+ if (ret) {
+ dev_err(tas_dev->dev,
+ "%s: request_firmware %x open status: %d.\n", __func__,
+ tas_dev->sdw_peripheral->id.unique_id, ret);
+ goto out;
+ }
+
+ tasdevice_dspfw_ready(fw_entry, tas_dev);
+
+out:
+ if (fw_entry)
+ release_firmware(fw_entry);
+ return 0;
+}
+
+static const struct snd_soc_component_driver
+ soc_codec_driver_tasdevice = {
+ .probe = tasdevice_comp_probe,
+ .controls = tas2783_snd_controls,
+ .num_controls = ARRAY_SIZE(tas2783_snd_controls),
+ .dapm_widgets = tasdevice_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(tasdevice_dapm_widgets),
+ .dapm_routes = tasdevice_audio_map,
+ .num_dapm_routes = ARRAY_SIZE(tasdevice_audio_map),
+ .idle_bias_on = 1,
+ .endianness = 1,
+};
+
+static int tasdevice_init(struct tasdevice_priv *tas_dev)
+{
+ int ret;
+
+ dev_set_drvdata(tas_dev->dev, tas_dev);
+
+ ret = devm_snd_soc_register_component(tas_dev->dev,
+ &soc_codec_driver_tasdevice, tasdevice_dai_driver,
+ ARRAY_SIZE(tasdevice_dai_driver));
+ if (ret) {
+ dev_err(tas_dev->dev, "%s: codec register error:%d.\n",
+ __func__, ret);
+ return ret;
+ }
+
+ /* set autosuspend parameters */
+ pm_runtime_set_autosuspend_delay(tas_dev->dev, 3000);
+ pm_runtime_use_autosuspend(tas_dev->dev);
+
+ /* make sure the device does not suspend immediately */
+ pm_runtime_mark_last_busy(tas_dev->dev);
+ pm_runtime_enable(tas_dev->dev);
+
+ return 0;
+}
+
+static int tasdevice_read_prop(struct sdw_slave *slave)
+{
+ struct sdw_slave_prop *prop = &slave->prop;
+ struct sdw_dpn_prop *dpn;
+ unsigned long addr;
+ int nval, i;
+ u32 bit;
+
+ prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY;
+ prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY;
+
+ prop->paging_support = true;
+
+ /* first we need to allocate memory for set bits in port lists */
+ prop->source_ports = BIT(2); /* BITMAP: 00000100 */
+ prop->sink_ports = BIT(1); /* BITMAP: 00000010 */
+
+ nval = hweight32(prop->source_ports);
+ prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval,
+ sizeof(*prop->src_dpn_prop), GFP_KERNEL);
+ if (!prop->src_dpn_prop)
+ return -ENOMEM;
+
+ i = 0;
+ dpn = prop->src_dpn_prop;
+ addr = prop->source_ports;
+ for_each_set_bit(bit, &addr, 32) {
+ dpn[i].num = bit;
+ dpn[i].type = SDW_DPN_FULL;
+ dpn[i].simple_ch_prep_sm = true;
+ dpn[i].ch_prep_timeout = 10;
+ i++;
+ }
+
+ /* do this again for sink now */
+ nval = hweight32(prop->sink_ports);
+ prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval,
+ sizeof(*prop->sink_dpn_prop), GFP_KERNEL);
+ if (!prop->sink_dpn_prop)
+ return -ENOMEM;
+
+ i = 0;
+ dpn = prop->sink_dpn_prop;
+ addr = prop->sink_ports;
+ for_each_set_bit(bit, &addr, 32) {
+ dpn[i].num = bit;
+ dpn[i].type = SDW_DPN_FULL;
+ dpn[i].simple_ch_prep_sm = true;
+ dpn[i].ch_prep_timeout = 10;
+ i++;
+ }
+
+ /* set the timeout values */
+ prop->clk_stop_timeout = 20;
+
+ return 0;
+}
+
+static int tasdevice_io_init(struct device *dev,
+ struct sdw_slave *slave)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ int ret;
+
+ regcache_cache_only(tas_priv->regmap, false);
+
+ if (tas_priv->first_hw_init) {
+ regcache_cache_bypass(tas_priv->regmap, true);
+ } else {
+ /*
+ * PM runtime is only enabled when a Slave reports as Attached
+ * Update count of parent 'active' children.
+ */
+ pm_runtime_set_active(&slave->dev);
+ }
+
+ /* sw reset */
+ ret = regmap_write(tas_priv->regmap, TAS2873_REG_SWRESET,
+ TAS2873_REG_SWRESET_RESET);
+ if (ret) {
+ dev_err(tas_priv->dev, "Reset failed.\n");
+ goto out;
+ }
+
+ if (tas_priv->first_hw_init) {
+ regcache_cache_bypass(tas_priv->regmap, false);
+ regcache_mark_dirty(tas_priv->regmap);
+ }
+
+ tas_priv->first_hw_init = true;
+ tas_priv->hw_init = true;
+
+out:
+ return ret;
+}
+
+static int tasdevice_update_status(struct sdw_slave *slave,
+ enum sdw_slave_status status)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(&slave->dev);
+
+ if (status == SDW_SLAVE_UNATTACHED)
+ tas_priv->hw_init = false;
+ /*
+ * Perform initialization only if slave status
+ * is present and hw_init flag is false
+ */
+ if (tas_priv->hw_init || status != SDW_SLAVE_ATTACHED)
+ return 0;
+
+ /* perform I/O transfers required for Slave initialization */
+ return tasdevice_io_init(&slave->dev, slave);
+}
+
+/*
+ * slave_ops: callbacks for get_clock_stop_mode, clock_stop and
+ * port_prep are not defined for now
+ */
+static const struct sdw_slave_ops tasdevice_sdw_ops = {
+ .read_prop = tasdevice_read_prop,
+ .update_status = tasdevice_update_status,
+};
+
+static int tasdevice_sdw_probe(struct sdw_slave *peripheral,
+ const struct sdw_device_id *id)
+{
+ struct device *dev = &peripheral->dev;
+ struct tasdevice_priv *tas_dev;
+
+ tas_dev = devm_kzalloc(dev, sizeof(*tas_dev), GFP_KERNEL);
+ if (!tas_dev)
+ return -ENOMEM;
+
+ tas_dev->dev = dev;
+ tas_dev->sdw_peripheral = peripheral;
+ /*
+ * Mark hw_init to false
+ * HW init will be performed when device reports present
+ */
+ tas_dev->hw_init = false;
+ tas_dev->first_hw_init = false;
+
+ dev_set_drvdata(dev, tas_dev);
+
+ tas_dev->regmap = devm_regmap_init_sdw(peripheral, &tasdevice_regmap);
+ if (IS_ERR(tas_dev->regmap))
+ return dev_err_probe(dev, PTR_ERR(tas_dev->regmap),
+ "Failed devm_regmap_init_sdw.");
+
+ return tasdevice_init(tas_dev);
+}
+
+static int tasdevice_sdw_remove(struct sdw_slave *peripheral)
+{
+ struct tasdevice_priv *tas_dev = dev_get_drvdata(&peripheral->dev);
+
+ if (tas_dev->first_hw_init)
+ pm_runtime_disable(tas_dev->dev);
+
+ return 0;
+}
+
+static const struct sdw_device_id tasdevice_sdw_id[] = {
+ SDW_SLAVE_ENTRY(0x0102, 0x0000, 0),
+ {}
+};
+MODULE_DEVICE_TABLE(sdw, tasdevice_sdw_id);
+
+static int __maybe_unused tas2783_sdca_dev_suspend(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+
+ if (!tas_priv->hw_init)
+ return 0;
+
+ regcache_cache_only(tas_priv->regmap, true);
+
+ return 0;
+}
+
+#define TAS2783_PROBE_TIMEOUT_MS 5000
+
+static int __maybe_unused tas2783_sdca_dev_resume(struct device *dev)
+{
+ struct sdw_slave *slave = dev_to_sdw_dev(dev);
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ unsigned long time;
+
+ if (!tas_priv->first_hw_init)
+ return 0;
+
+ if (!slave->unattach_request)
+ goto regmap_sync;
+
+ time = wait_for_completion_timeout(&slave->initialization_complete,
+ msecs_to_jiffies(TAS2783_PROBE_TIMEOUT_MS));
+ if (!time) {
+ dev_err(&slave->dev, "Init not complete, timed out\n");
+ sdw_show_ping_status(slave->bus, true);
+
+ return -ETIMEDOUT;
+ }
+
+regmap_sync:
+ slave->unattach_request = 0;
+ regcache_cache_only(tas_priv->regmap, false);
+ regcache_sync(tas_priv->regmap);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tas2783_sdca_pm = {
+ SYSTEM_SLEEP_PM_OPS(tas2783_sdca_dev_suspend,
+ tas2783_sdca_dev_resume)
+ RUNTIME_PM_OPS(tas2783_sdca_dev_suspend,
+ tas2783_sdca_dev_resume, NULL)
+};
+
+static struct sdw_driver tasdevice_sdw_driver = {
+ .driver = {
+ .name = "slave-tas2783",
+ .pm = &tas2783_sdca_pm,
+ },
+ .probe = tasdevice_sdw_probe,
+ .remove = tasdevice_sdw_remove,
+ .ops = &tasdevice_sdw_ops,
+ .id_table = tasdevice_sdw_id,
+};
+
+module_sdw_driver(tasdevice_sdw_driver);
+
+MODULE_AUTHOR("Baojun Xu <baojun.xu@ti.com>");
+MODULE_AUTHOR("Shenghao Ding <shenghao-ding@ti.com>");
+MODULE_DESCRIPTION("ASoC TAS2783 SoundWire Driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,106 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * ALSA SoC Texas Instruments TAS2783 Audio Smart Amplifier
+ *
+ * Copyright (C) 2023 - 2024 Texas Instruments Incorporated
+ * https://www.ti.com
+ *
+ * Author: Baojun Xu <baojun.xu@ti.com>
+ * Shenghao Ding <shenghao-ding@ti.com>
+ */
+
+#ifndef __TAS2783_H__
+#define __TAS2783_H__
+
+/* Unique id start */
+#define TAS2783_UNIQUE_ID_BASE 0x08
+#define TAS2783_MAX_DEV_NUM 8
+
+#define TAS2783_DEVICE_RATES (SNDRV_PCM_RATE_44100 | \
+ SNDRV_PCM_RATE_48000 | \
+ SNDRV_PCM_RATE_96000 | \
+ SNDRV_PCM_RATE_88200)
+
+#define TAS2783_DEVICE_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \
+ SNDRV_PCM_FMTBIT_S24_LE | \
+ SNDRV_PCM_FMTBIT_S32_LE)
+
+/* BOOK, PAGE Control Register */
+#define TASDEVICE_REG(book, page, reg) ((book * 256 * 256) + 0x8000 + \
+ (page * 128) + reg)
+
+/*Software Reset */
+#define TAS2873_REG_SWRESET TASDEVICE_REG(0x0, 0x00, 0x01)
+#define TAS2873_REG_SWRESET_MASK BIT(0)
+#define TAS2873_REG_SWRESET_RESET BIT(0)
+
+#define TAS2873_REG_PWR_CTRL TASDEVICE_REG(0x0, 0x00, 0x02)
+#define TAS2783_REG_AEF_MASK GENMASK(4, 3)
+#define TAS2783_REG_AEF_ACTIVE 0
+#define TAS2783_REG_AEF_INACTIVE GENMASK(4, 3)
+#define TAS2783_REG_PWR_MODE_MASK GENMASK(2, 0)
+#define TAS2783_REG_PWR_MODE_ACTIVE 0
+#define TAS2783_REG_PWR_MODE_SW_PWD BIT(1)
+
+#define TAS2783_REG_TDM_RX_CFG TASDEVICE_REG(0x0, 0x00, 0x0a)
+
+/* Volume control */
+#define TAS2783_DVC_LVL TASDEVICE_REG(0x0, 0x00, 0x1a)
+#define TAS2783_AMP_LEVEL TASDEVICE_REG(0x0, 0x00, 0x03)
+#define TAS2783_AMP_LEVEL_MASK GENMASK(5, 1)
+
+/* Calibration data */
+#define TAS2783_CALIBRATION_RE TASDEVICE_REG(0x0, 0x17, 0x74)
+#define TAS2783_CALIBRATION_RE_LOW TASDEVICE_REG(0x0, 0x18, 0x14)
+#define TAS2783_CALIBRATION_INV_RE TASDEVICE_REG(0x0, 0x18, 0x0c)
+#define TAS2783_CALIBRATION_POW TASDEVICE_REG(0x0, 0x13, 0x70)
+#define TAS2783_CALIBRATION_TLIMIT TASDEVICE_REG(0x0, 0x18, 0x7c)
+
+/* TAS2783 SDCA Control - function number */
+#define TAS2783_FUNC_TYPE_SMART_AMP 0x01
+
+/* TAS2783 SDCA entity */
+#define TAS2783_SDCA_ENT_FU21 0x01
+#define TAS2783_SDCA_ENT_FU23 0x02
+
+/* TAS2783 SDCA control */
+#define TAS2783_SDCA_CTL_REQ_POWER_STATE 0x01
+#define TAS2783_SDCA_CTL_FU_MUTE 0x01
+#define TAS2783_SDCA_CTL_FU_VOLUME 0x02
+#define TAS2783_SDCA_CTL_UDMPU_CLUSTER 0x10
+
+#define TAS2783_DEVICE_CHANNEL_LEFT 1
+#define TAS2783_DEVICE_CHANNEL_RIGHT 2
+#define TAS2783_DSPFW_FILENAME_LEN 64
+
+#define TAS2783_MAX_CALIDATA_SIZE 256
+
+#define TAS2783_CALIDATAV1_TIMESTAMP_INDX 40
+#define TAS2783_CALIDATAV1_CRC32_INDX 41
+/* 8 devs * 20 bytes calibrated data/dev + 4 bytes Timestamp */
+#define TAS2783_CALIDATAV1_BYTE_SIZE (8 * 20 + 4)
+
+#define TAS2783_CALIDATAV2_TIMESTAMP_INDX 2
+
+struct tas2783_firmware_node {
+ unsigned int vendor_id;
+ unsigned int file_id;
+ unsigned int version_id;
+ unsigned int length;
+ unsigned int download_addr;
+};
+
+struct calibration_data {
+ unsigned long total_sz;
+ unsigned char data[TAS2783_MAX_CALIDATA_SIZE];
+};
+
+struct tasdevice_priv {
+ struct sdw_slave *sdw_peripheral;
+ struct regmap *regmap;
+ struct device *dev;
+ bool hw_init;
+ bool first_hw_init;
+};
+
+#endif /*__TAS2783_H__ */
The tas2783 is a smart audio amplifier with integrated MIPI SoundWire interface (Version 1.2.1 compliant), I2C, and I2S/TDM interfaces designed for portable applications. An on-chip DSP supports Texas Instruments SmartAmp speaker protection algorithm. The integrated speaker voltage and current sense provides for real-time monitoring of loudspeakers. The ASoC component provides the majority of the functionality of the device, all the audio functions. Signed-off-by: Shenghao Ding <shenghao-ding@ti.com> --- Change in v12: - simplify tasdevice_set_sdw_stream - fixed some Linux coding style - fixed the spelling mistakes - Select left/right channel based on unique id - a longer description has been added - remove unused crc8 in KCONFIG - Invert of RE here means reciprocal of RE - correct indentation - correct the wrong pow calibrated register - correct comment on RESET register - fixed usually lines don't end with an open parenthesis - fixed tasdevice_sdw_shutdown - use defines for function, entity, etc. for readable - remove unnecessary codec_lock in component_probe() - remove struct sdw_stream_data - remove unused macro definitions - use BIT(2) and BIT(1) instead of 0x2 and 0x1 - implement pm_runtime - reg_start is u8, reg_start + i only adds i byte, it should be reg_start + i * 4, because the calibration values - fixed total_sz in tas2783_calibration - add a define for TASDEVICE_REG(0, 0, 0x0a) - rework macro style in header file - Add select CRC32 - rewrite the mute and the return value handling - Add comments on bin file - Add link_id into the fw name to distinguish the same sdw id on different sdw id. - remove unnecessary mutex_lock - use set_active() in tasdevice_io_init and move all other parts in the probe. - move pm_runtime_get_noresume to the probe - fix the return value of putvol function - add put_noidle in tasdevice_sdw_remove - remove unused header file(of.h) - correct the style of the multi-line comment - Set the readable registers in tas2783_readable_register for debugfs - Use new PM macros - Use default put and get inline SOC_SINGLE_RANGE_TLV and SOC_SINGLE_SX_TLV - Use respective %pt to log the calibrated time - Remove unnecessary struct tm - Add trailing comma tasdevice_dapm_widgets and tasdevice_audio_map - Rewrite the return value handling in tasdevice_sdw_probe - use dev_num instead of id.unique_id - rework the log - Add code to check the size of calibrated data in UEFI - Add description of Layout of calibrated Data in UEFI - switch back link_id and unique_id to identify the devcie - unique_id offset as the device index of the calibrated data - update calibrated data layout stored in UEFI, add link_id and unique_id into the calibrated data in case of tas2783 sitting in different SDQW buses. - correct the wrong unique_id - set the unique_id as hex style in dsp bin file name - use __func__ in the dev_err message in two identical logs intas2783_apply_calibv1/v2. - In tas2783_apply_calibv2, the very least move initializations to a different line. - No need for separate j variable, reuse i in tasdevice_read_prop. - remove unused "struct sdw_bus_params params", unsigned char dev_name[32] pstream, and chip_id - define dspfw_binaryname as a local variable in tasdevice_comp_probe. - reduce a lot of indentation in tasdevice_mute and spilte tasdevice_mute into tasdevice_enable_echo_ref and tasdevice_playback - remove tas2783_reg_defaults - use REGCACHE_MAPLE instead of REGCACHE_RBTREE - define fw_node_sz to store the node size - remove "struct snd_soc_component *component" - Add some SDCA registers as readable - remove unnecessary dev_dbg log for timestamp - playback still work without calibrated data stored in UEFI, for example bypass mode. Even if in case of dsp mode, algo can still work with default calibrated data. So, not an error, use dev_info for them --- sound/soc/codecs/Kconfig | 16 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/tas2783-sdw.c | 892 +++++++++++++++++++++++++++++++++ sound/soc/codecs/tas2783.h | 106 ++++ 4 files changed, 1016 insertions(+) create mode 100644 sound/soc/codecs/tas2783-sdw.c create mode 100644 sound/soc/codecs/tas2783.h