@@ -32,14 +32,12 @@
/**
* struct plat_max3100 - MAX3100 SPI UART platform data
- * @loopback: force MAX3100 in loopback
* @crystal: 1 for 3.6864 Mhz, 0 for 1.8432
*
* You should use this structure in your machine description to specify
* how the MAX3100 is connected.
*/
struct plat_max3100 {
- int loopback;
int crystal;
};
@@ -109,6 +107,7 @@ struct max3100_port {
int minor; /* minor number */
int crystal; /* 1 if 3.6864Mhz crystal 0 for 1.8432 */
+ int loopback_commit; /* need to change loopback */
int loopback; /* 1 if we are in loopback mode */
/* for handling irqs: need workqueue since we do spi_sync */
@@ -257,7 +256,7 @@ static void max3100_work(struct work_struct *w)
struct max3100_port *s = container_of(w, struct max3100_port, work);
int rxchars;
u16 tx, rx;
- int conf, cconf, crts;
+ int conf, cconf, cloopback, crts;
struct circ_buf *xmit = &s->port.state->xmit;
dev_dbg(&s->spi->dev, "%s\n", __func__);
@@ -268,11 +267,15 @@ static void max3100_work(struct work_struct *w)
conf = s->conf;
cconf = s->conf_commit;
s->conf_commit = 0;
+ cloopback = s->loopback_commit;
+ s->loopback_commit = 0;
crts = s->rts_commit;
s->rts_commit = 0;
spin_unlock(&s->conf_lock);
if (cconf)
max3100_sr(s, MAX3100_WC | conf, &rx);
+ if (cloopback)
+ max3100_sr(s, 0x4001, &rx);
if (crts) {
max3100_sr(s, MAX3100_WD | MAX3100_TE |
(s->rts ? MAX3100_RTS : 0), &rx);
@@ -397,18 +400,24 @@ static void max3100_set_mctrl(struct uart_port *port, unsigned int mctrl)
struct max3100_port *s = container_of(port,
struct max3100_port,
port);
- int rts;
+ int loopback, rts;
dev_dbg(&s->spi->dev, "%s\n", __func__);
+ loopback = (mctrl & TIOCM_LOOP) > 0;
rts = (mctrl & TIOCM_RTS) > 0;
spin_lock(&s->conf_lock);
+ if (s->loopback != loopback) {
+ s->loopback = loopback;
+ s->loopback_commit = 1;
+ }
if (s->rts != rts) {
s->rts = rts;
s->rts_commit = 1;
- max3100_dowork(s);
}
+ if (s->loopback_commit || s->rts_commit)
+ max3100_dowork(s);
spin_unlock(&s->conf_lock);
}
@@ -595,12 +604,6 @@ static int max3100_startup(struct uart_port *port)
return -EBUSY;
}
- if (s->loopback) {
- u16 tx, rx;
- tx = 0x4001;
- max3100_sr(s, tx, &rx);
- }
-
s->conf_commit = 1;
max3100_dowork(s);
/* wait for clock to settle */
@@ -755,7 +758,6 @@ static int max3100_probe(struct spi_device *spi)
spi_set_drvdata(spi, max3100s[i]);
pdata = dev_get_platdata(&spi->dev);
max3100s[i]->crystal = pdata->crystal;
- max3100s[i]->loopback = pdata->loopback;
max3100s[i]->minor = i;
timer_setup(&max3100s[i]->timer, max3100_timeout, 0);
Enable or disable loopback at run-time. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> --- drivers/tty/serial/max3100.c | 26 ++++++++++++++------------ 1 file changed, 14 insertions(+), 12 deletions(-)