@@ -33,14 +33,14 @@
Some more general comments about what we are doing:
The i2c bus is a 2 wire serial bus, with clock (SCL) and data (SDA)
- lines. To communicate on the bus (as a master, we don't act as a slave),
+ lines. To communicate on the bus (as a host, we don't act as a client),
we first initiate a start condition (ivtv_start). We then write the
address of the device that we want to communicate with, along with a flag
- that indicates whether this is a read or a write. The slave then issues
+ that indicates whether this is a read or a write. The client then issues
an ACK signal (ivtv_ack), which tells us that it is ready for reading /
writing. We then proceed with reading or writing (ivtv_read/ivtv_write),
and finally issue a stop condition (ivtv_stop) to make the bus available
- to other masters.
+ to other hosts.
There is an additional form of transaction where a write may be
immediately followed by a read. In this case, there is no intervening
@@ -379,7 +379,7 @@ static int ivtv_waitsda(struct ivtv *itv, int val)
return 0;
}
-/* Wait for the slave to issue an ACK */
+/* Wait for the client to issue an ACK */
static int ivtv_ack(struct ivtv *itv)
{
int ret = 0;
@@ -407,7 +407,7 @@ static int ivtv_ack(struct ivtv *itv)
return ret;
}
-/* Write a single byte to the i2c bus and wait for the slave to ACK */
+/* Write a single byte to the i2c bus and wait for the client to ACK */
static int ivtv_sendbyte(struct ivtv *itv, unsigned char byte)
{
int i, bit;
@@ -471,7 +471,7 @@ static int ivtv_readbyte(struct ivtv *itv, unsigned char *byte, int nack)
return 0;
}
-/* Issue a start condition on the i2c bus to alert slaves to prepare for
+/* Issue a start condition on the i2c bus to alert clients to prepare for
an address write */
static int ivtv_start(struct ivtv *itv)
{
@@ -534,7 +534,7 @@ static int ivtv_stop(struct ivtv *itv)
return 0;
}
-/* Write a message to the given i2c slave. do_stop may be 0 to prevent
+/* Write a message to the given i2c client. do_stop may be 0 to prevent
issuing the i2c stop condition (when following with a read) */
static int ivtv_write(struct ivtv *itv, unsigned char addr, unsigned char *data, u32 len, int do_stop)
{
@@ -558,7 +558,7 @@ static int ivtv_write(struct ivtv *itv, unsigned char addr, unsigned char *data,
return ret;
}
-/* Read data from the given i2c slave. A stop condition is always issued. */
+/* Read data from the given i2c client. A stop condition is always issued. */
static int ivtv_read(struct ivtv *itv, unsigned char addr, unsigned char *data, u32 len)
{
int retry, ret = -EREMOTEIO;
I2C v7, SMBus 3.2, and I3C 1.1.1 specifications have replaced "master/slave" with more appropriate terms. Inspired by and following on to Wolfram's series to fix drivers/i2c/[1], fix the terminology for users of I2C_ALGOBIT bitbanging interface, now that the approved verbiage exists in the specification. Compile tested, no functionality changes intended [1]: https://lore.kernel.org/all/20240322132619.6389-1-wsa+renesas@sang-engineering.com/ Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> --- drivers/media/pci/ivtv/ivtv-i2c.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)