new file mode 100644
@@ -0,0 +1,149 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+//
+// ALSA SoC Texas Instruments TAS2781 Audio Smart Amplifier
+//
+// Copyright (C) 2024 Texas Instruments Incorporated
+// https://www.ti.com
+//
+// The TAS2781 driver implements a flexible and configurable
+// algo coefficient setting for TAS2781 chips.
+//
+// Author: Baojun Xu <baojun.xu@ti.com>
+//
+
+#ifndef __TAS2781_SPI_H__
+#define __TAS2781_SPI_H__
+
+#define TASDEVICE_RATES \
+ (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \
+ SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_88200)
+
+#define TASDEVICE_FORMATS \
+ (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE | \
+ SNDRV_PCM_FMTBIT_S32_LE)
+
+#define TASDEVICE_MAX_BOOK_NUM 256
+#define TASDEVICE_MAX_PAGE 128
+
+#define TASDEVICE_MAX_SIZE (TASDEVICE_MAX_BOOK_NUM * TASDEVICE_MAX_PAGE)
+
+/* PAGE Control Register (available in page0 of each book) */
+#define TASDEVICE_PAGE_SELECT 0x00
+#define TASDEVICE_BOOKCTL_PAGE 0x00
+#define TASDEVICE_BOOKCTL_REG 127
+#define TASDEVICE_BOOK_ID(reg) (reg / TASDEVICE_MAX_SIZE)
+#define TASDEVICE_PAGE_ID(reg) ((reg % TASDEVICE_MAX_SIZE) / \
+ TASDEVICE_MAX_PAGE)
+#define TASDEVICE_PAGE_REG(reg) ((reg % TASDEVICE_MAX_SIZE) % \
+ TASDEVICE_MAX_PAGE)
+#define TASDEVICE_PGRG(reg) (reg % TASDEVICE_MAX_SIZE)
+#define TASDEVICE_REG(book, page, reg) (((book * TASDEVICE_MAX_SIZE) + \
+ (page * TASDEVICE_MAX_PAGE)) + reg)
+
+/* Software Reset */
+#define TAS2781_REG_SWRESET TASDEVICE_REG(0x0, 0X0, 0x01)
+#define TAS2781_REG_SWRESET_RESET BIT(0)
+
+/* I2C Checksum */
+#define TASDEVICE_Checksum TASDEVICE_REG(0x0, 0x0, 0x7E)
+
+/* Volume control */
+#define TAS2781_DVC_LVL TASDEVICE_REG(0x0, 0x0, 0x1A)
+#define TAS2781_AMP_LEVEL TASDEVICE_REG(0x0, 0x0, 0x03)
+#define TAS2781_AMP_LEVEL_MASK GENMASK(5, 1)
+
+#define TASDEVICE_CMD_SING_W 0x1
+#define TASDEVICE_CMD_BURST 0x2
+#define TASDEVICE_CMD_DELAY 0x3
+#define TASDEVICE_CMD_FIELD_W 0x4
+
+#define TAS2781_SPI_MAX_FREQ (4 * HZ_PER_MHZ)
+
+#define TASDEVICE_CRC8_POLYNOMIAL 0x4d
+#define TASDEVICE_SPEAKER_CALIBRATION_SIZE 20
+
+#define TASDEVICE_CALIBRATION_DATA_NAME L"CALI_DATA"
+#define TASDEVICE_CALIBRATION_DATA_SIZE 256
+
+enum calib_data {
+ R0_VAL = 0,
+ INV_R0,
+ R0LOW,
+ POWER,
+ TLIM,
+ CALIB_MAX
+};
+
+struct tasdevice_priv {
+ struct tasdevice_fw *cali_data_fmw;
+ struct tasdevice_rca rcabin;
+ struct tasdevice_fw *fmw;
+ struct gpio_desc *reset;
+ struct mutex codec_lock;
+ struct regmap *regmap;
+ struct device *dev;
+ struct tm tm;
+
+ const char *acpi_subsystem_id;
+ unsigned char crc8_lkp_tbl[CRC8_TABLE_SIZE];
+ unsigned char coef_binaryname[64];
+ unsigned char rca_binaryname[64];
+ unsigned char dev_name[32];
+
+ unsigned int err_code;
+ bool is_loading;
+ bool is_loaderr;
+ int cur_book;
+ int cur_prog;
+ int cur_conf;
+ int fw_state;
+ int index;
+ int irq;
+ void *client;
+ void *codec;
+ bool force_fwload_status;
+ bool playback_started;
+ unsigned int calibration_data[CALIB_MAX];
+
+ int (*fw_parse_variable_header)(struct tasdevice_priv *tas_priv,
+ const struct firmware *fmw, int offset);
+ int (*fw_parse_program_data)(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw,
+ const struct firmware *fmw, int offset);
+ int (*fw_parse_configuration_data)(struct tasdevice_priv *tas_priv,
+ struct tasdevice_fw *tas_fmw,
+ const struct firmware *fmw, int offset);
+ int (*tasdevice_load_block)(struct tasdevice_priv *tas_priv,
+ struct tasdev_blk *block);
+
+ int (*save_calibration)(struct tasdevice_priv *tas_priv);
+ void (*apply_calibration)(struct tasdevice_priv *tas_priv);
+};
+
+int tasdevice_spi_dev_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int *value);
+int tasdevice_spi_dev_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int value);
+int tasdevice_spi_dev_bulk_write(
+ struct tasdevice_priv *tas_priv, unsigned int reg,
+ unsigned char *p_data, unsigned int n_length);
+int tasdevice_spi_dev_bulk_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned char *p_data, unsigned int n_length);
+int tasdevice_spi_dev_update_bits(struct tasdevice_priv *tasdevice,
+ unsigned int reg, unsigned int mask, unsigned int value);
+
+void tasdevice_spi_select_cfg_blk(void *context, int conf_no,
+ unsigned char block_type);
+void tasdevice_spi_config_info_remove(void *context);
+int tasdevice_spi_dsp_parser(void *context);
+int tasdevice_spi_rca_parser(void *context, const struct firmware *fmw);
+void tasdevice_spi_dsp_remove(void *context);
+void tasdevice_spi_calbin_remove(void *context);
+int tasdevice_spi_select_tuningprm_cfg(void *context, int prm,
+ int cfg_no, int rca_conf_no);
+int tasdevice_spi_prmg_load(void *context, int prm_no);
+int tasdevice_spi_prmg_calibdata_load(void *context, int prm_no);
+void tasdevice_spi_tuning_switch(void *context, int state);
+int tas2781_spi_load_calibration(void *context, char *file_name,
+ unsigned short i);
+#endif /* __TAS2781_SPI_H__ */
new file mode 100644
@@ -0,0 +1,1240 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// TAS2781 HDA SPI driver
+//
+// Copyright 2024 Texas Instruments, Inc.
+//
+// Author: Baojun Xu <baojun.xu@ti.com>
+
+#include <linux/acpi.h>
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/cleanup.h>
+#include <linux/crc8.h>
+#include <linux/crc32.h>
+#include <linux/efi.h>
+#include <linux/firmware.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/time.h>
+#include <linux/types.h>
+#include <linux/units.h>
+
+#include <sound/hda_codec.h>
+#include <sound/soc.h>
+#include <sound/tas2781-dsp.h>
+#include <sound/tlv.h>
+#include <sound/tas2781-tlv.h>
+
+#include "tas2781-spi.h"
+
+#include "hda_local.h"
+#include "hda_auto_parser.h"
+#include "hda_component.h"
+#include "hda_jack.h"
+#include "hda_generic.h"
+
+/*
+ * No standard control callbacks for SNDRV_CTL_ELEM_IFACE_CARD
+ * Define two controls, one is Volume control callbacks, the other is
+ * flag setting control callbacks.
+ */
+
+/* Volume control callbacks for tas2781 */
+#define ACARD_SINGLE_RANGE_EXT_TLV(xname, xreg, xshift, xmin, xmax, xinvert, \
+ xhandler_get, xhandler_put, tlv_array) { \
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD, .name = (xname), \
+ .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \
+ SNDRV_CTL_ELEM_ACCESS_READWRITE, \
+ .tlv.p = (tlv_array), \
+ .info = snd_soc_info_volsw_range, \
+ .get = xhandler_get, .put = xhandler_put, \
+ .private_value = (unsigned long)&(struct soc_mixer_control) { \
+ .reg = xreg, .rreg = xreg, \
+ .shift = xshift, .rshift = xshift,\
+ .min = xmin, .max = xmax, .invert = xinvert, \
+ } \
+}
+
+/* Flag control callbacks for tas2781 */
+#define ACARD_SINGLE_BOOL_EXT(xname, xdata, xhandler_get, xhandler_put) { \
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD, \
+ .name = xname, \
+ .info = snd_ctl_boolean_mono_info, \
+ .get = xhandler_get, \
+ .put = xhandler_put, \
+ .private_value = xdata, \
+}
+
+struct tas2781_hda {
+ struct tasdevice_priv *priv;
+ struct acpi_device *dacpi;
+ struct snd_kcontrol *dsp_prog_ctl;
+ struct snd_kcontrol *dsp_conf_ctl;
+ struct snd_kcontrol *snd_ctls[3];
+ struct snd_kcontrol *prof_ctl;
+};
+
+static const struct regmap_range_cfg tasdevice_ranges[] = {
+ {
+ .range_min = 0,
+ .range_max = TASDEVICE_MAX_BOOK_NUM * TASDEVICE_MAX_PAGE,
+ .selector_reg = TASDEVICE_PAGE_SELECT,
+ .selector_mask = GENMASK(7, 0),
+ .selector_shift = 0,
+ .window_start = 0,
+ .window_len = TASDEVICE_MAX_PAGE,
+ },
+};
+
+static const struct regmap_config tasdevice_regmap = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_NONE,
+ .ranges = tasdevice_ranges,
+ .num_ranges = ARRAY_SIZE(tasdevice_ranges),
+ .max_register = TASDEVICE_MAX_BOOK_NUM * TASDEVICE_MAX_PAGE,
+};
+
+static int tasdevice_spi_switch_book(struct tasdevice_priv *tas_priv, int book)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ if (tas_priv->cur_book != book) {
+ /* Change to page 0 before book change. */
+ ret = regmap_write(map, TASDEVICE_PAGE_SELECT, 0);
+ if (ret < 0) {
+ dev_err(tas_priv->dev, "Switch page E=%d\n", ret);
+ return ret;
+ }
+ ret = regmap_write(map, TASDEVICE_BOOKCTL_REG, book);
+ if (ret < 0) {
+ dev_err(tas_priv->dev, "Switch Book E=%d\n", ret);
+ return ret;
+ }
+ tas_priv->cur_book = book;
+ }
+
+ return 0;
+}
+
+int tasdevice_spi_dev_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int *val)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, TASDEVICE_BOOK_ID(reg));
+ if (ret < 0)
+ return ret;
+
+ /*
+ * In our TAS2781 SPI mode, if read from other book (not book 0),
+ * or read from page number larger than 1 in book 0, one more byte
+ * read is needed, and first byte is a dummy byte, need to be ignored.
+ */
+ if ((TASDEVICE_BOOK_ID(reg) > 0) || (TASDEVICE_PAGE_ID(reg) > 1)) {
+ unsigned char data[2];
+
+ ret = regmap_bulk_read(map, TASDEVICE_PGRG(reg), data,
+ sizeof(data));
+ *val = data[1];
+ } else {
+ ret = regmap_read(map, TASDEVICE_PGRG(reg), val);
+ }
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int value)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, TASDEVICE_BOOK_ID(reg));
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_write(map, TASDEVICE_PGRG(reg), value);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_bulk_write(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned char *data, unsigned int len)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, TASDEVICE_BOOK_ID(reg));
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_bulk_write(map, TASDEVICE_PGRG(reg), data, len);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_bulk_read(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned char *data, unsigned int len)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, TASDEVICE_BOOK_ID(reg));
+ if (ret < 0)
+ return ret;
+
+ if (len > TASDEVICE_MAX_PAGE)
+ len = TASDEVICE_MAX_PAGE;
+ /*
+ * In our TAS2781 SPI mode, if read from other book (not book 0),
+ * or read from page number larger than 1 in book 0, one more byte
+ * read is needed, and first byte is a dummy byte, need to be ignored.
+ */
+ if ((TASDEVICE_BOOK_ID(reg) > 0) || (TASDEVICE_PAGE_ID(reg) > 1)) {
+ unsigned char buf[TASDEVICE_MAX_PAGE+1];
+
+ ret = regmap_bulk_read(map, TASDEVICE_PGRG(reg),
+ buf, len + 1);
+ memcpy(data, buf + 1, len);
+ } else {
+ ret = regmap_bulk_read(map, TASDEVICE_PGRG(reg), data, len);
+ }
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+int tasdevice_spi_dev_update_bits(struct tasdevice_priv *tas_priv,
+ unsigned int reg, unsigned int mask, unsigned int value)
+{
+ struct regmap *map = tas_priv->regmap;
+ int ret;
+
+ ret = tasdevice_spi_switch_book(tas_priv, TASDEVICE_BOOK_ID(reg));
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_update_bits(map, TASDEVICE_PGRG(reg), mask, value);
+ if (ret < 0)
+ dev_err(tas_priv->dev, "%s, E=%d\n", __func__, ret);
+
+ return ret;
+}
+
+static void tas2781_spi_reset(struct tasdevice_priv *tas_dev)
+{
+ int ret;
+
+ if (tas_dev->reset) {
+ gpiod_set_value_cansleep(tas_dev->reset, 0);
+ fsleep(800);
+ gpiod_set_value_cansleep(tas_dev->reset, 1);
+ } else {
+ ret = tasdevice_spi_dev_write(tas_dev, TAS2781_REG_SWRESET,
+ TAS2781_REG_SWRESET_RESET);
+ if (ret < 0)
+ dev_err(tas_dev->dev, "dev sw-reset fail, %d\n", ret);
+ }
+ fsleep(1000);
+}
+
+static int tascodec_spi_init(struct tasdevice_priv *tas_priv, void *codec,
+ struct module *module,
+ void (*cont)(const struct firmware *fw, void *context))
+{
+ int ret;
+
+ /*
+ * Codec Lock Hold to ensure that codec_probe and firmware parsing and
+ * loading do not simultaneously execute.
+ */
+ guard(mutex)(&tas_priv->codec_lock);
+
+ ret = scnprintf(tas_priv->rca_binaryname,
+ sizeof(tas_priv->rca_binaryname), "%sRCA%d.bin",
+ tas_priv->dev_name, tas_priv->index);
+ if (ret <= 0) {
+ dev_err(tas_priv->dev, "rca name err:0x%08x\n", ret);
+ return ret;
+ }
+ crc8_populate_msb(tas_priv->crc8_lkp_tbl, TASDEVICE_CRC8_POLYNOMIAL);
+ tas_priv->codec = codec;
+ ret = request_firmware_nowait(module, FW_ACTION_UEVENT,
+ tas_priv->rca_binaryname, tas_priv->dev, GFP_KERNEL, tas_priv,
+ cont);
+ if (ret)
+ dev_err(tas_priv->dev, "request_firmware_nowait err:0x%08x\n",
+ ret);
+
+ return ret;
+}
+
+static void tasdevice_spi_init(struct tasdevice_priv *tas_priv)
+{
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ tas_priv->cur_book = -1;
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ mutex_init(&tas_priv->codec_lock);
+}
+
+static int tasdevice_spi_amp_putvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ unsigned char mask;
+ int max = mc->max;
+ int val, ret;
+
+ mask = rounddown_pow_of_two(max);
+ mask <<= mc->shift;
+ val = clamp(invert ? max - ucontrol->value.integer.value[0] :
+ ucontrol->value.integer.value[0], 0, max);
+ ret = tasdevice_spi_dev_update_bits(tas_priv,
+ mc->reg, mask, (unsigned int)(val << mc->shift));
+ if (ret)
+ dev_err(tas_priv->dev, "set AMP vol error in dev %d\n",
+ tas_priv->index);
+
+ return ret;
+}
+
+static int tasdevice_spi_amp_getvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ unsigned char mask = 0;
+ int max = mc->max;
+ int ret, val;
+
+ /* Read the primary device */
+ ret = tasdevice_spi_dev_read(tas_priv, mc->reg, &val);
+ if (ret) {
+ dev_err(tas_priv->dev, "%s, get AMP vol error\n", __func__);
+ return ret;
+ }
+
+ mask = rounddown_pow_of_two(max);
+ mask <<= mc->shift;
+ val = (val & mask) >> mc->shift;
+ val = clamp(invert ? max - val : val, 0, max);
+ ucontrol->value.integer.value[0] = val;
+
+ return ret;
+}
+
+static int tasdevice_spi_digital_putvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ int max = mc->max;
+ int val, ret;
+
+ val = clamp(invert ? max - ucontrol->value.integer.value[0] :
+ ucontrol->value.integer.value[0], 0, max);
+ ret = tasdevice_spi_dev_write(tas_priv, mc->reg, (unsigned int)val);
+ if (ret)
+ dev_err(tas_priv->dev, "set digital vol err in dev %d\n",
+ tas_priv->index);
+
+ return ret;
+
+}
+
+static int tasdevice_spi_digital_getvol(struct tasdevice_priv *tas_priv,
+ struct snd_ctl_elem_value *ucontrol, struct soc_mixer_control *mc)
+{
+ unsigned int invert = mc->invert;
+ int max = mc->max;
+ int ret, val;
+
+ /* Read the primary device as the whole */
+ ret = tasdevice_spi_dev_read(tas_priv, mc->reg, &val);
+ if (ret) {
+ dev_err(tas_priv->dev, "%s, get digital vol err\n", __func__);
+ return ret;
+ }
+
+ val = clamp(invert ? max - val : val, 0, max);
+ ucontrol->value.integer.value[0] = val;
+
+ return ret;
+}
+
+static int tas2781_read_acpi(struct tas2781_hda *tas_hda, const char *hid,
+ int id)
+{
+ struct tasdevice_priv *p = tas_hda->priv;
+ struct acpi_device *adev;
+ struct device *physdev;
+ u32 values[HDA_MAX_COMPONENTS];
+ const char *property;
+ size_t nval;
+ int ret, i;
+
+ adev = acpi_dev_get_first_match_dev(hid, NULL, -1);
+ if (!adev) {
+ dev_err(p->dev, "Failed to find ACPI device: %s\n", hid);
+ return -ENODEV;
+ }
+
+ strscpy(p->dev_name, hid, sizeof(p->dev_name));
+ tas_hda->dacpi = adev;
+ physdev = get_device(acpi_get_first_physical_node(adev));
+ acpi_dev_put(adev);
+
+ /* No side-effect to the playback even if subsystem_id is NULL */
+ p->acpi_subsystem_id = acpi_get_subsystem_id(ACPI_HANDLE(physdev));
+
+ property = "ti,dev-index";
+ ret = device_property_count_u32(physdev, property);
+ if ((ret <= 0) || (ret > ARRAY_SIZE(values))) {
+ ret = -EINVAL;
+ goto err;
+ }
+ nval = ret;
+
+ ret = device_property_read_u32_array(physdev, property, values, nval);
+ if (ret)
+ goto err;
+
+ p->index = U8_MAX;
+ for (i = 0; i < nval; i++) {
+ if (values[i] == id) {
+ p->index = i;
+ break;
+ }
+ }
+ if (p->index == U8_MAX) {
+ dev_dbg(p->dev, "No index found in %s\n", property);
+ ret = -ENODEV;
+ goto err;
+ }
+
+ if (p->index == 0) {
+ /* All of amps share same RESET pin. */
+ p->reset = devm_gpiod_get_index_optional(physdev, "reset",
+ p->index, GPIOD_OUT_LOW);
+ if (IS_ERR(p->reset)) {
+ dev_err_probe(p->dev, ret, "Failed on reset GPIO\n");
+ goto err;
+ }
+ }
+
+ put_device(physdev);
+
+ return 0;
+
+err:
+ dev_err(p->dev, "read acpi error, ret: %d\n", ret);
+ put_device(physdev);
+ acpi_dev_put(adev);
+
+ return ret;
+}
+
+static void tas2781_hda_playback_hook(struct device *dev, int action)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ switch (action) {
+ case HDA_GEN_PCM_ACT_OPEN:
+ pm_runtime_get_sync(dev);
+ guard(mutex)(&tas_hda->priv->codec_lock);
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+ break;
+ case HDA_GEN_PCM_ACT_CLOSE:
+ guard(mutex)(&tas_hda->priv->codec_lock);
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+ break;
+ default:
+ dev_dbg(tas_hda->priv->dev,
+ "Playback action not supported: %d\n", action);
+ break;
+ }
+}
+
+static int tasdevice_info_profile(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->rcabin.ncfgs - 1;
+
+ return 0;
+}
+
+static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id;
+
+ return 0;
+}
+
+static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int max = tas_priv->rcabin.ncfgs - 1;
+ int val;
+
+ val = clamp(ucontrol->value.integer.value[0], 0, max);
+ if (tas_priv->rcabin.profile_cfg_id != val) {
+ tas_priv->rcabin.profile_cfg_id = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+static int tasdevice_info_programs(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->fmw->nr_programs - 1;
+
+ return 0;
+}
+
+static int tasdevice_info_config(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->fmw->nr_configurations - 1;
+
+ return 0;
+}
+
+static int tasdevice_program_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_prog;
+
+ return 0;
+}
+
+static int tasdevice_program_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int nr_program = ucontrol->value.integer.value[0];
+ int max = tas_priv->fmw->nr_programs - 1;
+ int val;
+
+ val = clamp(nr_program, 0, max);
+
+ if (tas_priv->cur_prog != val) {
+ tas_priv->cur_prog = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+static int tasdevice_config_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_conf;
+
+ return 0;
+}
+
+static int tasdevice_config_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int max = tas_priv->fmw->nr_configurations - 1;
+ int val;
+
+ val = clamp(ucontrol->value.integer.value[0], 0, max);
+
+ if (tas_priv->cur_conf != val) {
+ tas_priv->cur_conf = val;
+ return 1;
+ }
+
+ return 0;
+}
+
+/*
+ * tas2781_digital_getvol - get the volum control
+ * @kcontrol: control pointer
+ * @ucontrol: User data
+ *
+ * Customer Kcontrol for tas2781 is primarily for regmap booking, paging
+ * depends on internal regmap mechanism.
+ * tas2781 contains book and page two-level register map, especially
+ * book switching will set the register BXXP00R7F, after switching to the
+ * correct book, then leverage the mechanism for paging to access the
+ * register.
+ *
+ * Return 0 if succeeded.
+ */
+static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_spi_digital_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_spi_amp_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ /* The check of the given value is in tasdevice_digital_putvol. */
+ return tasdevice_spi_digital_putvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ /* The check of the given value is in tasdevice_amp_putvol. */
+ return tasdevice_spi_amp_putvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_force_fwload_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = (int)tas_priv->force_fwload_status;
+ dev_dbg(tas_priv->dev, "%s : Force FWload %s\n", __func__,
+ str_on_off(tas_priv->force_fwload_status));
+
+ return 0;
+}
+
+static int tas2781_force_fwload_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ bool change, val = (bool)ucontrol->value.integer.value[0];
+
+ if (tas_priv->force_fwload_status == val) {
+ change = false;
+ } else {
+ change = true;
+ tas_priv->force_fwload_status = val;
+ }
+ dev_dbg(tas_priv->dev, "%s : Force FWload %s\n", __func__,
+ str_on_off(tas_priv->force_fwload_status));
+
+ return change;
+}
+
+static const struct snd_kcontrol_new tas2781_snd_controls[] = {
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Analog Gain", TAS2781_AMP_LEVEL,
+ 1, 0, 20, 0, tas2781_amp_getvol,
+ tas2781_amp_putvol, amp_vol_tlv),
+ ACARD_SINGLE_RANGE_EXT_TLV("Speaker Digital Gain", TAS2781_DVC_LVL,
+ 0, 0, 200, 1, tas2781_digital_getvol,
+ tas2781_digital_putvol, dvc_tlv),
+ ACARD_SINGLE_BOOL_EXT("Speaker Force Firmware Load", 0,
+ tas2781_force_fwload_get, tas2781_force_fwload_put),
+};
+
+static const struct snd_kcontrol_new tas2781_prof_ctrl = {
+ .name = "Speaker Profile Id",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_profile,
+ .get = tasdevice_get_profile_id,
+ .put = tasdevice_set_profile_id,
+};
+
+static const struct snd_kcontrol_new tas2781_dsp_prog_ctrl = {
+ .name = "Speaker Program Id",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_programs,
+ .get = tasdevice_program_get,
+ .put = tasdevice_program_put,
+};
+
+static const struct snd_kcontrol_new tas2781_dsp_conf_ctrl = {
+ .name = "Speaker Config Id",
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_config,
+ .get = tasdevice_config_get,
+ .put = tasdevice_config_put,
+};
+
+static void tas2781_apply_calib(struct tasdevice_priv *tas_priv)
+{
+ static const unsigned char page_array[CALIB_MAX] = {
+ 0x17, 0x18, 0x18, 0x13, 0x18,
+ };
+ static const unsigned char rgno_array[CALIB_MAX] = {
+ 0x74, 0x0c, 0x14, 0x70, 0x7c,
+ };
+ int j, rc;
+
+ /*
+ * If no calibration data exist in tasdevice_priv *tas_priv,
+ * calibration apply will be ignored, and use default values
+ * in firmware binary, which was loaded during firmware download.
+ */
+ if (tas_priv->calibration_data[0] == 0)
+ return;
+ /*
+ * Calibration data was saved in tasdevice_priv *tas_priv as:
+ * unsigned int calibration_data[CALIB_MAX];
+ * and every data (in 4 bytes) will be saved in register which in
+ * book 0, and page number in page_array[], offset was saved in
+ * rgno_array[].
+ */
+ for (j = 0; j < CALIB_MAX; j++) {
+ rc = tasdevice_spi_dev_bulk_write(tas_priv,
+ TASDEVICE_REG(0, page_array[j], rgno_array[j]),
+ (unsigned char *)&tas_priv->calibration_data[j], 4);
+ if (rc < 0)
+ dev_err(tas_priv->dev,
+ "chn %d calib %d bulk_wr err = %d\n",
+ tas_priv->index, j, rc);
+ }
+}
+
+/*
+ * Update the calibration data, including speaker impedance, f0, etc,
+ * into algo. Calibrate data is done by manufacturer in the factory.
+ * These data are used by Algo for calculating the speaker temperature,
+ * speaker membrane excursion and f0 in real time during playback.
+ * Calibration data format in EFI is V2, since 2024.
+ */
+static int tas2781_save_calibration(struct tasdevice_priv *tas_priv)
+{
+ /*
+ * GUID was used for data access in BIOS, it was provide by board
+ * manufactory, like HP: "{02f9af02-7734-4233-b43d-93fe5aa35db3}"
+ */
+ efi_guid_t efi_guid =
+ EFI_GUID(0x02f9af02, 0x7734, 0x4233,
+ 0xb4, 0x3d, 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3);
+ static efi_char16_t efi_name[] = TASDEVICE_CALIBRATION_DATA_NAME;
+ struct tm *tm = &tas_priv->tm;
+ unsigned long total_sz = 0;
+ unsigned int attr, crc;
+ unsigned int *tmp_val;
+ efi_status_t status;
+ unsigned char data[TASDEVICE_CALIBRATION_DATA_SIZE];
+
+ tas_priv->calibration_data[0] = 0;
+ status = efi.get_variable(efi_name, &efi_guid, &attr, &total_sz,
+ data);
+ if (status == EFI_BUFFER_TOO_SMALL) {
+ if (total_sz > TASDEVICE_CALIBRATION_DATA_SIZE)
+ return -ENOMEM;
+ /* Get variable contents into buffer */
+ status = efi.get_variable(efi_name, &efi_guid, &attr,
+ &total_sz, data);
+ }
+ if (status != EFI_SUCCESS)
+ return -EINVAL;
+
+ tmp_val = (unsigned int *)data;
+ if (tmp_val[0] == 2781) {
+ /*
+ * New features were added in calibrated Data V2:
+ * 1. Added some the fields to store the link_id and
+ * uniqie_id for multi-link solutions
+ * 2. Support flexible number of devices instead of
+ * fixed one in V1.
+ * Layout of calibrated data V2 in UEFI(total 256 bytes):
+ * ChipID (2781, 4 bytes)
+ * Device-Sum (4 bytes)
+ * TimeStamp of Calibration (4 bytes)
+ * for (i = 0; i < Device-Sum; i++) {
+ * Device #i index_info () {
+ * SDW link id (2bytes)
+ * SDW unique_id (2bytes)
+ * }
+ * Calibrated Data of Device #i (20 bytes)
+ * }
+ * CRC (4 bytes)
+ * Reserved (the rest)
+ */
+ crc = crc32(~0, data, 3 + tmp_val[0] * 6) ^ ~0;
+ dev_dbg(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n",
+ crc, tmp_val[3 + tmp_val[0] * 6]);
+
+ if (crc == tmp_val[3 + tmp_val[0] * 6]) {
+ time64_to_tm(tmp_val[2], 0, tm);
+ dev_dbg(tas_priv->dev, "Calibration date %pt.\n", tm);
+ for (int i = 0; i < CALIB_MAX; i++)
+ tas_priv->calibration_data[i] =
+ tmp_val[3 + tas_priv->index * 6 + i];
+ tas_priv->apply_calibration(tas_priv);
+ }
+ } else {
+ /*
+ * Calibration data is in V1 format.
+ * struct cali_data {
+ * char cali_data[20];
+ * }
+ *
+ * struct {
+ * struct cali_data cali_data[4];
+ * int TimeStamp of Calibration (4 bytes)
+ * int CRC (4 bytes)
+ * } ueft;
+ */
+ crc = crc32(~0, data, 84) ^ ~0;
+ dev_dbg(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n",
+ crc, tmp_val[21]);
+
+ if (crc == tmp_val[21]) {
+ time64_to_tm(tmp_val[20], 0, tm);
+ dev_dbg(tas_priv->dev, "Calibration date %pt.\n", tm);
+ for (int i = 0; i < CALIB_MAX; i++)
+ tas_priv->calibration_data[i] =
+ tmp_val[tas_priv->index * 5 + i];
+ tas_priv->apply_calibration(tas_priv);
+ }
+ }
+
+ return 0;
+}
+
+static void tas2781_hda_remove_controls(struct tas2781_hda *tas_hda)
+{
+ struct hda_codec *codec = tas_hda->priv->codec;
+
+ if (tas_hda->dsp_prog_ctl)
+ snd_ctl_remove(codec->card, tas_hda->dsp_prog_ctl);
+
+ if (tas_hda->dsp_conf_ctl)
+ snd_ctl_remove(codec->card, tas_hda->dsp_conf_ctl);
+
+ for (int i = ARRAY_SIZE(tas_hda->snd_ctls) - 1; i >= 0; i--)
+ if (tas_hda->snd_ctls[i])
+ snd_ctl_remove(codec->card, tas_hda->snd_ctls[i]);
+
+ if (tas_hda->prof_ctl)
+ snd_ctl_remove(codec->card, tas_hda->prof_ctl);
+}
+
+static void tasdev_fw_ready(const struct firmware *fmw, void *context)
+{
+ struct tasdevice_priv *tas_priv = context;
+ struct tas2781_hda *tas_hda = dev_get_drvdata(tas_priv->dev);
+ struct hda_codec *codec = tas_priv->codec;
+ int i, ret;
+
+ pm_runtime_get_sync(tas_priv->dev);
+ guard(mutex)(&tas_priv->codec_lock);
+
+ ret = tasdevice_spi_rca_parser(tas_priv, fmw);
+ if (ret)
+ goto out;
+
+ /* Add control one time only. */
+ if (tas_priv->index == 0) {
+ tas_hda->prof_ctl = snd_ctl_new1(&tas2781_prof_ctrl, tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->prof_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_prof_ctrl.name, ret);
+ goto out;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(tas2781_snd_controls); i++) {
+ tas_hda->snd_ctls[i] =
+ snd_ctl_new1(&tas2781_snd_controls[i],
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->snd_ctls[i]);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_snd_controls[i].name, ret);
+ goto out;
+ }
+ }
+ }
+
+ tasdevice_spi_dsp_remove(tas_priv);
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+ scnprintf(tas_priv->coef_binaryname, 64, "TAS2XXX%08X-%01d.bin",
+ codec->core.subsystem_id, tas_priv->index);
+ ret = tasdevice_spi_dsp_parser(tas_priv);
+ if (ret) {
+ dev_err(tas_priv->dev, "dspfw load %s error\n",
+ tas_priv->coef_binaryname);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ goto out;
+ }
+
+ /* Add control one time only. */
+ if (tas_priv->index == 0) {
+ tas_hda->dsp_prog_ctl = snd_ctl_new1(&tas2781_dsp_prog_ctrl,
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->dsp_prog_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_dsp_prog_ctrl.name, ret);
+ goto out;
+ }
+
+ tas_hda->dsp_conf_ctl = snd_ctl_new1(&tas2781_dsp_conf_ctrl,
+ tas_priv);
+ ret = snd_ctl_add(codec->card, tas_hda->dsp_conf_ctl);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_dsp_conf_ctrl.name, ret);
+ goto out;
+ }
+ }
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK;
+ tasdevice_spi_prmg_load(tas_priv, 0);
+ if (tas_priv->fmw->nr_programs > 0)
+ tas_priv->cur_prog = 0;
+ if (tas_priv->fmw->nr_configurations > 0)
+ tas_priv->cur_conf = 0;
+
+ tasdevice_spi_tuning_switch(tas_hda->priv, 0);
+
+ /*
+ * If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ tas_priv->save_calibration(tas_priv);
+
+out:
+ if (fmw)
+ release_firmware(fmw);
+ pm_runtime_mark_last_busy(tas_hda->priv->dev);
+ pm_runtime_put_autosuspend(tas_hda->priv->dev);
+}
+
+static int tas2781_hda_bind(struct device *dev, struct device *master,
+ void *master_data)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+ struct hda_codec *codec;
+ int ret;
+
+ if (!comps || tas_hda->priv->index < 0 ||
+ tas_hda->priv->index >= HDA_MAX_COMPONENTS)
+ return -EINVAL;
+
+ comps = &comps[tas_hda->priv->index];
+ if (comps->dev)
+ return -EBUSY;
+
+ codec = comps->codec;
+
+ pm_runtime_get_sync(dev);
+
+ comps->dev = dev;
+
+ strscpy(comps->name, dev_name(dev), sizeof(comps->name));
+
+ ret = tascodec_spi_init(tas_hda->priv, codec, THIS_MODULE,
+ tasdev_fw_ready);
+ if (!ret)
+ comps->playback_hook = tas2781_hda_playback_hook;
+
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+
+ return ret;
+}
+
+static void tas2781_hda_unbind(struct device *dev,
+ struct device *master, void *master_data)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+
+ comps = &comps[tas_hda->priv->index];
+
+ if (comps->dev == dev) {
+ comps->dev = NULL;
+ memset(comps->name, 0, sizeof(comps->name));
+ comps->playback_hook = NULL;
+ }
+
+ tas2781_hda_remove_controls(tas_hda);
+
+ tasdevice_spi_config_info_remove(tas_hda->priv);
+ tasdevice_spi_dsp_remove(tas_hda->priv);
+
+ tas_hda->priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+}
+
+static const struct component_ops tas2781_hda_comp_ops = {
+ .bind = tas2781_hda_bind,
+ .unbind = tas2781_hda_unbind,
+};
+
+static void tas2781_hda_remove(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ pm_runtime_get_sync(tas_hda->priv->dev);
+ pm_runtime_disable(tas_hda->priv->dev);
+
+ component_del(tas_hda->priv->dev, &tas2781_hda_comp_ops);
+
+ pm_runtime_put_noidle(tas_hda->priv->dev);
+
+ mutex_destroy(&tas_hda->priv->codec_lock);
+}
+
+static int tas2781_hda_spi_probe(struct spi_device *spi)
+{
+ struct tasdevice_priv *tas_priv;
+ struct tas2781_hda *tas_hda;
+ const char *device_name;
+ int ret = 0;
+
+ tas_hda = devm_kzalloc(&spi->dev, sizeof(*tas_hda), GFP_KERNEL);
+ if (!tas_hda)
+ return -ENOMEM;
+
+ spi->max_speed_hz = TAS2781_SPI_MAX_FREQ;
+
+ tas_priv = devm_kzalloc(&spi->dev, sizeof(*tas_priv), GFP_KERNEL);
+ if (!tas_priv)
+ goto err;
+ tas_priv->dev = &spi->dev;
+ tas_priv->client = spi;
+ tas_hda->priv = tas_priv;
+ tas_priv->regmap = devm_regmap_init_spi(spi, &tasdevice_regmap);
+ if (IS_ERR(tas_priv->regmap)) {
+ ret = PTR_ERR(tas_priv->regmap);
+ dev_err(tas_priv->dev, "Failed to allocate regmap: %d\n",
+ ret);
+ goto err;
+ }
+ if (strstr(dev_name(&spi->dev), "TXNW2781")) {
+ device_name = "TXNW2781";
+ tas_priv->save_calibration = tas2781_save_calibration;
+ tas_priv->apply_calibration = tas2781_apply_calib;
+ } else if (strstr(dev_name(&spi->dev), "TIAS2781")) {
+ device_name = "TIAS2781";
+ tas_priv->save_calibration = tas2781_save_calibration;
+ tas_priv->apply_calibration = tas2781_apply_calib;
+ } else {
+ goto err;
+ }
+
+ tas_priv->irq = spi->irq;
+ dev_set_drvdata(&spi->dev, tas_hda);
+ ret = tas2781_read_acpi(tas_hda, device_name,
+ spi_get_chipselect(spi, 0));
+ if (ret)
+ return dev_err_probe(tas_priv->dev, ret,
+ "Platform not supported\n");
+
+ tasdevice_spi_init(tas_priv);
+
+ pm_runtime_set_autosuspend_delay(tas_priv->dev, 3000);
+ pm_runtime_use_autosuspend(tas_priv->dev);
+ pm_runtime_mark_last_busy(tas_priv->dev);
+ pm_runtime_set_active(tas_priv->dev);
+ pm_runtime_get_noresume(tas_priv->dev);
+ pm_runtime_enable(tas_priv->dev);
+
+ pm_runtime_put_autosuspend(tas_priv->dev);
+
+ tas2781_spi_reset(tas_priv);
+
+ ret = component_add(tas_priv->dev, &tas2781_hda_comp_ops);
+ if (ret) {
+ dev_err(tas_priv->dev, "Register component failed: %d\n", ret);
+ pm_runtime_disable(tas_priv->dev);
+ }
+
+err:
+ if (ret)
+ tas2781_hda_remove(&spi->dev);
+ return ret;
+}
+
+static void tas2781_hda_spi_remove(struct spi_device *spi)
+{
+ tas2781_hda_remove(&spi->dev);
+}
+
+static int tas2781_runtime_suspend(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ dev_dbg(tas_hda->priv->dev, "Runtime Suspend\n");
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ if (tas_hda->priv->playback_started) {
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+ tas_hda->priv->playback_started = false;
+ }
+
+ tas_hda->priv->cur_book = -1;
+ tas_hda->priv->cur_prog = -1;
+ tas_hda->priv->cur_conf = -1;
+
+ return 0;
+}
+
+static int tas2781_runtime_resume(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+
+ dev_dbg(tas_hda->priv->dev, "Runtime Resume\n");
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ tasdevice_spi_prmg_load(tas_hda->priv, tas_hda->priv->cur_prog);
+
+ /*
+ * If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ tas_hda->priv->apply_calibration(tas_hda->priv);
+
+ return 0;
+}
+
+static int tas2781_system_suspend(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ int ret;
+
+ dev_info(tas_hda->priv->dev, "System Suspend %p\n", tas_hda);
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ return ret;
+
+ /* Shutdown chip before system suspend */
+ tasdevice_spi_tuning_switch(tas_hda->priv, 1);
+
+ /*
+ * Reset GPIO may be shared, so cannot reset here.
+ * However beyond this point, amps may be powered down.
+ */
+ return 0;
+}
+
+static int tas2781_system_resume(struct device *dev)
+{
+ struct tas2781_hda *tas_hda = dev_get_drvdata(dev);
+ int ret;
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ guard(mutex)(&tas_hda->priv->codec_lock);
+
+ tas_hda->priv->cur_book = -1;
+ tas_hda->priv->cur_prog = -1;
+ tas_hda->priv->cur_conf = -1;
+
+ tas2781_spi_reset(tas_hda->priv);
+ tasdevice_spi_prmg_load(tas_hda->priv, tas_hda->priv->cur_prog);
+
+ /*
+ * If calibrated data occurs error, dsp will still work with default
+ * calibrated data inside algo.
+ */
+ tas_hda->priv->apply_calibration(tas_hda->priv);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tas2781_hda_pm_ops = {
+ RUNTIME_PM_OPS(tas2781_runtime_suspend, tas2781_runtime_resume, NULL)
+ SYSTEM_SLEEP_PM_OPS(tas2781_system_suspend, tas2781_system_resume)
+};
+
+static const struct spi_device_id tas2781_hda_spi_id[] = {
+ { "tas2781-hda", },
+ {}
+};
+
+static const struct acpi_device_id tas2781_acpi_hda_match[] = {
+ {"TXNW2781", },
+ {"TIAS2781", },
+ {}
+};
+MODULE_DEVICE_TABLE(acpi, tas2781_acpi_hda_match);
+
+static struct spi_driver tas2781_hda_spi_driver = {
+ .driver = {
+ .name = "tas2781-hda",
+ .acpi_match_table = tas2781_acpi_hda_match,
+ .pm = &tas2781_hda_pm_ops,
+ },
+ .id_table = tas2781_hda_spi_id,
+ .probe = tas2781_hda_spi_probe,
+ .remove = tas2781_hda_spi_remove,
+};
+module_spi_driver(tas2781_hda_spi_driver);
+
+MODULE_DESCRIPTION("TAS2781 HDA SPI Driver");
+MODULE_AUTHOR("Baojun, Xu, <baojun.xug@ti.com>");
+MODULE_LICENSE("GPL");
Main source code for tas2781 hda driver for SPI. Signed-off-by: Baojun Xu <baojun.xu@ti.com> --- v4: - Move include of sound/tas2781-dsp.h to c source file tas2781_hda_spi.c, tas2781_spi_fwlib.c, as it's not needed in header file tas2781-spi.h - Use page and book number define in other micro define - Change 4000000 to (4 * HZ_PER_MHZ) - Add define for calibration variable name and size in UEFI. - Remove structure tasdevice & tasdevice_irqinfo, and move variables in to structure tasdevice_priv - Remove some unused variables in sttructure tasdevice_priv - Remove function declare of tascodec_init(), use tascodec_spi_init() - Remove function declare of tasdevice_remove() - Add array_size.h included in tas2781_hda_spi.c - Add cleanup.h included for change mutex to guard - Add units.h included - Include tas2781-dsp.h - Remove unused variables in tas2781_hda structure - Change 0xff to GENMASK(7, 0) - Change 128 to define of max page size - Change code as all variables was moved to tasdevice_priv structure - Change comments for error in book write, or page write - Remove initial of ret, and return 0 directly - Change comments for wrong typo, add space in front and end - Add check for bulk read, max size should be a page size - Change usleep_rang() to fsleep() - Change mutex_lock to guard(mutex), and remove mutex_unlock() - Change tasdevice_spi_init() to void from int as no value return required - Change second parameter to sizeof - Remove tasdevice_clamp(), use clamp() - Add compatible with old hardware id "TIAS2781" - Remove cs_gpio and spi device in tas2781_read_acpi() as use default CS - Change dev-index check, return -EINVAL if it's <= 0 - Change 0xFF to U8_MAX - Remove GPIO get for chip-select, use default from SPI device - Perform RESET in first AMP only as all AMPs share same RESET pin - return 0 directly in some simple routine to avoid variable initial - Change comments for function which was used by system - Change "ON" "OFF" to function str_on_off(...) - Change format of GUID - Add temp buffer for first efi.get_variable() - Free data if it was allocated - Change format of debug message of calibration date time print - Remove total_sz = 0, as it's not needed - Move save_calibration to after tuning_switch to avoid calibration data overwrite - Remove dev from structure tasdevice_hda, use dev in tasdevice_priv - Remove 0 from { "tas2781-hda", 0}, & {"TXNW2781", 0}, v3: - Change format for some define in tas2781-spi.h. - Add define for TASDEVICE_MAX_BOOK_NUM, TASDEVICE_MAX_PAGE. - Move declare of "enum calib_data {" to header file from source file. - Remove "enum device_catlog_id {" as only one platform was supported now. - Remove "struct calidata", as we will save pure calibration data only. - Remove "struct calidata", "enum device_catlog_id" in tasdevice_priv. - Add calibration_data in tasdevice_priv to save pure calibration data. - Remove declare of tasdevice_save_calibration() and tasdevice_apply_calibration(), as it will be used within same c file. - Add below header files included in tas2781_hda_spi.c: bits.h, mutex.h, property.h, time.h, types.h. - Move two micro define to header file tas2781-spi.h. - Change format of some micro define. - Change format of some structure. - Remove irq in tas2781_hda, as have it already in tasdevice_priv. - Remove some local functions declare as not necessarily. - Return error if regmap_write() failed. - Change fixed value 2 to sizeof(data). - Remove all of EXPORT_SYMBOL_GPL, as all of function was called within same module. - Remove empty line after last return in some functions. - Remove some variable initialyzation. - Remove variable sub, store acpi_subsystem_id directly. - Remove wrong comments for device index, it's must, can't be NULL. - Remove some local variables, use elements in structure directly. - Append commas in last element of an array. - Change calibration data process, didn't save all of calibration data in EFI, get in local, and save pure calibration data in tasdevice_priv. - Call tasdevice_save_calibration() from function pointer in tasdevice_priv; - Remove subid as one platform was supported only, needn't check. - Add initialyzation for local variable. - Move regmap initialyzation to before acpi read. - Call tasdevice_apply_calibration() from function pointer in tasdevice_priv; - Remove MODULE_IMPORT_NS(SND_SOC_TAS2781_FMWLIB), as all functions was performed within same module. v2: - Update information in file header of tas2781-spi.h. - Remove useless micro define. - Change TASDEVICE_I2CChecksum to TASDEVICE_Checksum - Remove enum control_bus as current code support SPI only. - Remove device define as current code support TAS2781 only. - Remove spi_device **spi_devs in structure tasdevice_priv. - Remove cal_binaryname in structure tasdevice_priv. - Remove ndev in structure tasdevice_priv. - Change isacpi and isspi, replace by control_bus(I2C or SPI). - Remove void tasdevice_spi_dsp_remove(void *context). - Add acpi_device and irq in structure tas2781_hda in tas2781_hda_spi.c. - Remove parameter chn in all of registers access functions. - Add tascodec_spi_init(). - Add chip select gpio set for SPI device. - Change tasdevice_tuning_switch() to tasdevice_spi_tuning_switch(). - Change device offset from tas_priv->ndev to tas_priv->index. - Change tasdevice_dsp_remove() to tasdevice_spi_dsp_remove(). - tasdevice_prmg_load() to tasdevice_spi_prmg_load(). - Change tasdevice_config_info_remove() to tasdevice_spi_config_info_remove(). - Add one dummy byte shift when read from page 2~127, or not book 0. - Change tasdevice_spi_change_chn_book() to tasdevice_spi_switch_book() - Perform put_device(physdev) before error return. - Change calibration data id to 2781 from 2783 in EFI - Change calibration data structure name in comments. --- sound/pci/hda/tas2781-spi.h | 149 ++++ sound/pci/hda/tas2781_hda_spi.c | 1240 +++++++++++++++++++++++++++++++ 2 files changed, 1389 insertions(+) create mode 100644 sound/pci/hda/tas2781-spi.h create mode 100644 sound/pci/hda/tas2781_hda_spi.c