@@ -10,4 +10,5 @@ MMC/SD/SDIO card support
mmc-dev-attrs
mmc-dev-parts
mmc-async-req
+ mmc-test
mmc-tools
new file mode 100644
@@ -0,0 +1,287 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================
+MMC Test Framework
+========================
+
+Overview
+========
+
+The MMC Test Framework (`mmc_test`) is designed to facilitate testing of MMC (MultiMediaCard) devices. It provides a set of tests and utilities to verify the functionality and performance of MMC devices.
+
+Initialization
+==============
+
+To use the ``mmc_test`` framework, follow these steps:
+
+1. **Enable the MMC Test Framework**:
+
+ Ensure that the ``CONFIG_MMC_TEST`` kernel configuration option is enabled. This can be done by configuring the kernel:
+
+ .. code-block:: none
+
+ make menuconfig
+
+ Navigate to:
+
+ Device Drivers --->
+ <*> MMC/SD/SDIO card support --->
+ [*] MMC host test driver
+
+ Alternatively, you can enable it directly in the kernel configuration file:
+
+ .. code-block:: none
+
+ echo "CONFIG_MMC_TEST=y" >> .config
+
+ Rebuild and install the kernel if necessary.
+
+2. **Load the MMC Test Module**:
+
+ If the ``mmc_test`` framework is built as a module, you need to load it using ``modprobe``:
+
+ .. code-block:: none
+
+ modprobe mmc_test
+
+Binding the MMC Card for Testing
+================================
+
+To enable MMC testing, you need to unbind the MMC card from the ``mmcblk`` driver and bind it to the ``mmc_test`` driver. This allows the ``mmc_test`` framework to take control of the MMC card for testing purposes.
+
+1. Identify the MMC card:
+
+ .. code-block:: sh
+
+ ls /sys/bus/mmc/devices/
+
+ This will list the MMC devices, such as ``mmc0:0001``.
+
+2. Unbind the MMC card from the ``mmcblk`` driver:
+
+ .. code-block:: sh
+
+ echo 'mmc0:0001' > /sys/bus/mmc/drivers/mmcblk/unbind
+
+3. Bind the MMC card to the ``mmc_test`` driver:
+
+ .. code-block:: sh
+
+ echo 'mmc0:0001' > /sys/bus/mmc/drivers/mmc_test/bind
+
+After binding, you should see a line in the kernel log indicating that the card has been claimed for testing:
+
+.. code-block:: none
+
+ mmc_test mmc0:0001: Card claimed for testing.
+
+
+Usage - Debugfs Entries
+=======================
+
+Once the ``mmc_test`` framework is enabled, you can interact with the following debugfs entries located in ``/sys/kernel/debug/mmc0/mmc0:0001``:
+
+1. **test**:
+
+ This file is used to run specific tests. Write the test number to this file to execute a test.
+
+ .. code-block:: sh
+
+ echo <test_number> > /sys/kernel/debug/mmc0/mmc0:0001/test
+
+ The test result is indicated in the kernel log info. You can view the kernel log using the `dmesg` command or by checking the log file in `/var/log/`.
+
+ .. code-block:: sh
+
+ dmesg | grep mmc0
+
+ Example:
+
+ To run test number 4 (Basic read with data verification):
+
+ .. code-block:: sh
+
+ echo 4 > /sys/kernel/debug/mmc0/mmc0:0001/test
+
+ Check the kernel log for the result:
+
+ .. code-block:: sh
+
+ dmesg | grep mmc0
+
+2. **testlist**:
+
+ This file lists all available tests. You can read this file to see the list of tests and their corresponding numbers.
+
+ .. code-block:: sh
+
+ cat /sys/kernel/debug/mmc0/mmc0:0001/testlist
+
+ The available tests are listed in the table below:
+
++------+--------------------------------+---------------------------------------------+
+| Test | Test Name | Test Description |
++======+================================+=============================================+
+| 0 | Run all tests | Runs all available tests |
++------+--------------------------------+---------------------------------------------+
+| 1 | Basic write | Performs a basic write operation of a |
+| | | single 512-Byte block to the MMC card |
+| | | without data verification. |
++------+--------------------------------+---------------------------------------------+
+| 2 | Basic read | Same for read |
++------+--------------------------------+---------------------------------------------+
+| 3 | Basic write | Performs a basic write operation of a |
+| | (with data verification) | single 512-Byte block to the MMC card |
+| | | with data verification by reading back |
+| | | the written data and comparing it. |
++------+--------------------------------+---------------------------------------------+
+| 4 | Basic read | Same for read |
+| | (with data verification) | |
++------+--------------------------------+---------------------------------------------+
+| 5 | Multi-block write | Performs a multi-block write operation of |
+| | | 8 blocks (each 512 bytes) to the MMC card. |
++------+--------------------------------+---------------------------------------------+
+| 6 | Multi-block read | Same for read |
++------+--------------------------------+---------------------------------------------+
+| 7 | Power of two block writes | Performs write operations with block sizes |
+| | | that are powers of two, starting from 1 |
+| | | byte up to 256 bytes, to the MMC card. |
++------+--------------------------------+---------------------------------------------+
+| 8 | Power of two block reads | Same for read |
++------+--------------------------------+---------------------------------------------+
+| 9 | Weird sized block writes | Performs write operations with varying |
+| | | block sizes starting from 3 bytes and |
+| | | increasing by 7 bytes each iteration, up |
+| | | to 511 bytes, to the MMC card. |
++------+--------------------------------+---------------------------------------------+
+| 10 | Weird sized block reads | same for read |
++------+--------------------------------+---------------------------------------------+
+| 11 | Badly aligned write | Performs write operations with buffers |
+| | | starting at different alignments (0 to 7 |
+| | | bytes offset) to test how the MMC card |
+| | | handles unaligned data transfers. |
++------+--------------------------------+---------------------------------------------+
+| 12 | Badly aligned read | same for read |
++------+--------------------------------+---------------------------------------------+
+| 13 | Badly aligned multi-block write| same for multi-write |
++------+--------------------------------+---------------------------------------------+
+| 14 | Badly aligned multi-block read | same for multi-read |
++------+--------------------------------+---------------------------------------------+
+| 15 | Proper xfer_size at write | intentionally create a broken transfer by |
+| | (Start failure) | modifying the MMC request in a way that it |
+| | | will not perform as expected, e.g. use |
+| | | MMC_WRITE_BLOCK for a multi-block transfer |
++------+--------------------------------+---------------------------------------------+
+| 16 | Proper xfer_size at read | same for read |
+| | (Start failure) | |
++------+--------------------------------+---------------------------------------------+
+| 17 | Proper xfer_size at write | same for 2 blocks |
+| | (Midway failure) | |
++------+--------------------------------+---------------------------------------------+
+| 18 | Proper xfer_size at read | same for read |
+| | (Midway failure) | |
++------+--------------------------------+---------------------------------------------+
+| 19 | Highmem write | use a high memory page |
++------+--------------------------------+---------------------------------------------+
+| 20 | Highmem read | same for read |
++------+--------------------------------+---------------------------------------------+
+| 21 | Multi-block highmem write | same for multi-write |
++------+--------------------------------+---------------------------------------------+
+| 22 | Multi-block highmem read | same for mult-read |
++------+--------------------------------+---------------------------------------------+
+| 23 | Best-case read performance | Performs 512K sequential read (non sg) |
++------+--------------------------------+---------------------------------------------+
+| 24 | Best-case write performance | same for write |
++------+--------------------------------+---------------------------------------------+
+| 25 | Best-case read performance | Same using sg |
+| | (Into scattered pages) | |
++------+--------------------------------+---------------------------------------------+
+| 26 | Best-case write performance | same for write |
+| | (From scattered pages) | |
++------+--------------------------------+---------------------------------------------+
+| 27 | Single read performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 28 | Single write performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 29 | Single trim performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 30 | Consecutive read performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 31 | Consecutive write performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 32 | Consecutive trim performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 33 | Random read performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 34 | Random write performance | By transfer size |
++------+--------------------------------+---------------------------------------------+
+| 35 | Large sequential read | Into scattered pages |
++------+--------------------------------+---------------------------------------------+
+| 36 | Large sequential write | From scattered pages |
++------+--------------------------------+---------------------------------------------+
+| 37 | Write performance | With blocking req 4k to 4MB |
++------+--------------------------------+---------------------------------------------+
+| 38 | Write performance | With non-blocking req 4k to 4MB |
++------+--------------------------------+---------------------------------------------+
+| 39 | Read performance | With blocking req 4k to 4MB |
++------+--------------------------------+---------------------------------------------+
+| 40 | Read performance | With non-blocking req 4k to 4MB |
++------+--------------------------------+---------------------------------------------+
+| 41 | Write performance | Blocking req 1 to 512 sg elems |
++------+--------------------------------+---------------------------------------------+
+| 42 | Write performance | Non-blocking req 1 to 512 sg elems |
++------+--------------------------------+---------------------------------------------+
+| 43 | Read performance | Blocking req 1 to 512 sg elems |
++------+--------------------------------+---------------------------------------------+
+| 44 | Read performance | Non-blocking req 1 to 512 sg elems |
++------+--------------------------------+---------------------------------------------+
+| 45 | Reset test | |
++------+--------------------------------+---------------------------------------------+
+| 46 | Commands during read | No Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+| 47 | Commands during write | No Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+| 48 | Commands during read | Use Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+| 49 | Commands during write | Use Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+| 50 | Commands during non-blocking | Read - use Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+| 51 | Commands during non-blocking | Write - use Set Block Count (CMD23) |
++------+--------------------------------+---------------------------------------------+
+
+Test Results
+============
+
+The results of the tests are logged in the kernel log. Each test logs the start, end, and result of the test. The possible results are:
+
+- **OK**: The test completed successfully.
+- **FAILED**: The test failed.
+- **UNSUPPORTED (by host)**: The test is unsupported by the host.
+- **UNSUPPORTED (by card)**: The test is unsupported by the card.
+- **ERROR**: An error occurred during the test.
+
+Example Kernel Log Output
+=========================
+
+When running a test, you will see log entries similar to the following in the kernel log:
+
+.. code-block:: none
+
+ [ 1234.567890] mmc0: Starting tests of card mmc0:0001...
+ [ 1234.567891] mmc0: Test case 4. Basic read (with data verification)...
+ [ 1234.567892] mmc0: Result: OK
+ [ 1234.567893] mmc0: Tests completed.
+
+In this example, test case 4 (Basic read with data verification) was executed, and the result was OK.
+
+
+Contributing
+============
+
+Contributions to the `mmc_test` framework are welcome. Please follow the standard Linux kernel contribution guidelines and submit patches to the appropriate maintainers.
+
+Contact
+=======
+
+For more information or to report issues, please contact the MMC subsystem maintainers.
Add missing documentation for mmc-test. Signed-off-by: Avri Altman <avri.altman@wdc.com> --- Documentation/driver-api/mmc/index.rst | 1 + Documentation/driver-api/mmc/mmc-test.rst | 287 ++++++++++++++++++++++ 2 files changed, 288 insertions(+) create mode 100644 Documentation/driver-api/mmc/mmc-test.rst