@@ -306,6 +306,10 @@
};
};
};
+
+ wcnss@a21b000 {
+ status = "okay";
+ };
};
usb2513 {
@@ -720,4 +720,17 @@
};
};
};
+
+ wcnss_pin_a: wcnss-active {
+ pinmux {
+ pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "wcss_wlan";
+ };
+
+ pinconf {
+ pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
};
@@ -14,6 +14,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8916.h>
#include <dt-bindings/reset/qcom,gcc-msm8916.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
/ {
model = "Qualcomm Technologies, Inc. MSM8916";
@@ -82,7 +83,7 @@
no-map;
};
- wcnss@89300000 {
+ wcnss_mem: wcnss@89300000 {
reg = <0x0 0x89300000 0x0 0x600000>;
no-map;
};
@@ -853,6 +854,76 @@
memory-region = <&mpss_mem>;
};
};
+
+ pronto: wcnss@a21b000 {
+ compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+ reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+
+ memory-region = <&wcnss_mem>;
+
+ interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+ vddmx-supply = <&pm8916_l3>;
+ vddpx-supply = <&pm8916_l7>;
+
+ qcom,state = <&wcnss_smp2p_out 0>;
+ qcom,state-names = "stop";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+
+ status = "disabled";
+
+ iris {
+ compatible = "qcom,wcn3620";
+
+ clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+ clock-names = "xo";
+
+ vddxo-supply = <&pm8916_l7>;
+ vddrfa-supply = <&pm8916_s3>;
+ vddpa-supply = <&pm8916_l9>;
+ vdddig-supply = <&pm8916_l5>;
+ };
+
+ smd-edge {
+ interrupts = <0 142 1>;
+
+ qcom,ipc = <&apcs 8 17>;
+ qcom,smd-edge = <6>;
+ qcom,remote-pid = <4>;
+
+ label = "pronto";
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ qcom,mmio = <&pronto>;
+
+ bt {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wifi {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>,
+ <0 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+ };
+ };
+ };
+ };
};
smd {
Add the wcnss remoteproc node the SMD edge and the wcnss ctrl, bluetooth and wifi nodes specified and enable this on db410c. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> --- This still require the last wcn36xx and scm-interrupted patches to land, but as those won't affect the dts I'm posting this anyway. arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 4 ++ arch/arm64/boot/dts/qcom/msm8916-pins.dtsi | 13 ++++++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 73 +++++++++++++++++++++++++++++- 3 files changed, 89 insertions(+), 1 deletion(-) -- 2.5.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html