@@ -1136,13 +1136,15 @@ static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
reg |= LINKCTRL_BUS_FILTER_BYPASS(0xf);
writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
- reg = readl(regs_base + EXYNOS850_DRD_UTMI);
- reg |= UTMI_FORCE_BVALID | UTMI_FORCE_VBUSVALID;
- writel(reg, regs_base + EXYNOS850_DRD_UTMI);
-
- reg = readl(regs_base + EXYNOS850_DRD_HSP);
- reg |= HSP_VBUSVLDEXT | HSP_VBUSVLDEXTSEL;
- writel(reg, regs_base + EXYNOS850_DRD_HSP);
+ if (!phy_drd->sw) {
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg |= UTMI_FORCE_BVALID | UTMI_FORCE_VBUSVALID;
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg |= HSP_VBUSVLDEXT | HSP_VBUSVLDEXTSEL;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+ }
reg = readl(regs_base + EXYNOS850_DRD_SSPPLLCTL);
reg &= ~SSPPLLCTL_FSEL;
@@ -1407,9 +1409,44 @@ static int exynos5_usbdrd_orien_sw_set(struct typec_switch_dev *sw,
enum typec_orientation orientation)
{
struct exynos5_usbdrd_phy *phy_drd = typec_switch_get_drvdata(sw);
+ int ret;
+
+ if (phy_drd->orientation == orientation)
+ return 0;
+
+ ret = clk_bulk_prepare_enable(phy_drd->drv_data->n_clks, phy_drd->clks);
+ if (ret) {
+ dev_err(phy_drd->dev, "Failed to enable PHY clocks(s)\n");
+ return ret;
+ }
+
+ scoped_guard(mutex, &phy_drd->phy_mutex) {
+ void __iomem * const regs_base = phy_drd->reg_phy;
+ unsigned int reg;
+
+ if (orientation == TYPEC_ORIENTATION_NONE) {
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg &= ~(UTMI_FORCE_VBUSVALID | UTMI_FORCE_BVALID);
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg |= HSP_VBUSVLDEXTSEL;
+ reg &= ~HSP_VBUSVLDEXT;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+ } else {
+ reg = readl(regs_base + EXYNOS850_DRD_UTMI);
+ reg |= UTMI_FORCE_VBUSVALID | UTMI_FORCE_BVALID;
+ writel(reg, regs_base + EXYNOS850_DRD_UTMI);
+
+ reg = readl(regs_base + EXYNOS850_DRD_HSP);
+ reg |= HSP_VBUSVLDEXTSEL | HSP_VBUSVLDEXT;
+ writel(reg, regs_base + EXYNOS850_DRD_HSP);
+ }
- scoped_guard(mutex, &phy_drd->phy_mutex)
phy_drd->orientation = orientation;
+ }
+
+ clk_bulk_disable(phy_drd->drv_data->n_clks, phy_drd->clks);
return 0;
}
To make USB runtime suspend work when a UDC has been bound, the phy needs to inform the USBDRD controller (DWC3) that Vbus and bvalid are gone, so that it can in turn raise the respective gadget interrupt with event == DWC3_DEVICE_EVENT_DISCONNECT, which will cause the USB stack to clean up, allowing DWC3 to enter runtime suspend. On e850 and gs101 this isn't working, as the respective signals are not directly connected, and instead this driver uses override bits in the PHY IP to set those signals. It currently forcefully sets them to 'on', so the above mentioned interrupt will not be raised, preventing runtime suspend. To detect that state, update this driver to act on the TCPC's orientation signal - when orientation == NONE, Vbus is gone and we can clear the respective bits. Similarly, for other orientation values we re-enable them. This makes runtime suspend work on platforms with a TCPC (like Pixel6), while keeping compatibility with platforms without (e850-96). With runtime suspend working, USB-C cable orientation detection now also fully works on such platforms, and the link comes up as Superspeed as expected irrespective of the cable orientation and whether UDC / gadget are configured and active. Signed-off-by: André Draszik <andre.draszik@linaro.org> --- drivers/phy/samsung/phy-exynos5-usbdrd.c | 53 +++++++++++++++++++++++++++----- 1 file changed, 45 insertions(+), 8 deletions(-)