diff mbox series

[v5] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port

Message ID 20250221144941.2844333-1-macpaul.lin@mediatek.com
State New
Headers show
Series [v5] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port | expand

Commit Message

Macpaul Lin (ζž—ζ™Ίζ–Œ) Feb. 21, 2025, 2:49 p.m. UTC 
From: Fabien Parent <fparent@baylibre.com>

Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding
configuration for TCPC Port, USB-C connector, MUX IT5205 and related
settings.

Configure dual role switch capability, set up PD (Power Delivery) profiles,
and establish endpoints for SS (SuperSpeed) and HS (HighSpeed) USB.

Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode
to "otg" for OTG (On-The-Go) mode operation.

Add ITE IT5205 (TYPEC MUX) under I2C2 bus and configure its properties;
also add references and configurations to 'typec-mux' node.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Yow-Shin Liou <yow-shin.liou@mediatek.com>
Signed-off-by: Simon Sun <simon.sun@yunjingtech.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
---
 .../dts/mediatek/mt8395-genio-1200-evk.dts    | 100 ++++++++++++++++++
 1 file changed, 100 insertions(+)

Changes for v2:
 - Drop the no need '1/2' DT Schema update patch in the 1st version.  
 - Fix indent for 'ports' node, it should under the 'connector' node.
 - Correct the index for 'port@0' and 'port@1' node.

Changes for v3:
 - Correct the order between new added nodes.

Changes for v4:
 - Reorder for property 'op-sink-microwatt'.
 - Fix indentation for 'source-pdos' and 'sink-pdos' nodes.
 - Correct node 'pin-cmd-dat' with 'pins-vbus'.
 - Add both Highspeed and Superspeed ports to ssusb0 port.
 - Set 'role-switch-default-mode' = "peripheral" for ssusb0 port.
 - Rename endpoint of USB data port to 'mtu3_hs0_role_sw' and
   'mtu3_ss0_role_sw'.
 - Drop it5205fn phandle for node typec-mux@48.
 - Reorder properties of typec-mux@48
 - Add "Reviewed-by:" tag. Thanks!

Changes for v5:
 - Squash two patches into one patch and refine commit messages:
   suggested by reviewer.
 - Drop 'role-switch-default-mode'
 - Add altmodes settings
 - Drop 'Reviewed-by:' tag since the two sub patches has been combined
   into a new patch.
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
index 1ef6262b65c9..6d139d40f8b3 100644
--- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
@@ -224,6 +224,21 @@  &i2c2 {
 	pinctrl-0 = <&i2c2_pins>;
 	pinctrl-names = "default";
 	status = "okay";
+
+	typec-mux@48 {
+		compatible = "ite,it5205";
+		reg = <0x48>;
+		vcc-supply = <&mt6359_vibr_ldo_reg>;
+		mode-switch;
+		orientation-switch;
+		status = "okay";
+
+		port {
+			it5205_sbu_ep: endpoint {
+				remote-endpoint = <&mt6360_ssusb_sbu_ep>;
+			};
+		};
+	};
 };
 
 &i2c6 {
@@ -330,6 +345,61 @@  mt6360_ldo7: ldo7 {
 				regulator-always-on;
 			};
 		};
+
+		tcpc {
+			compatible = "mediatek,mt6360-tcpc";
+			interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "PD_IRQB";
+
+			connector {
+				compatible = "usb-c-connector";
+				label = "USB-C";
+				data-role = "dual";
+				op-sink-microwatt = <10000000>;
+				power-role = "dual";
+				try-power-role = "sink";
+
+				source-pdos = <PDO_FIXED(5000, 1000,
+							 PDO_FIXED_DUAL_ROLE |
+							 PDO_FIXED_DATA_SWAP)>;
+				sink-pdos = <PDO_FIXED(5000, 2000,
+						       PDO_FIXED_DUAL_ROLE |
+						       PDO_FIXED_DATA_SWAP)>;
+
+				altmodes {
+					displayport {
+						svid = /bits/ 16 <0xff01>;
+						vdo = <0x00001c46>;
+					};
+				};
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						typec_con_hs: endpoint {
+							remote-endpoint = <&mtu3_hs0_role_sw>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						typec_con_ss: endpoint {
+							remote-endpoint = <&mtu3_ss0_role_sw>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+						mt6360_ssusb_sbu_ep: endpoint {
+							remote-endpoint = <&it5205_sbu_ep>;
+						};
+					};
+				};
+			};
+		};
 	};
 };
 
@@ -755,6 +825,13 @@  pins-reset {
 		};
 	};
 
+	u3_p0_vbus: u3-p0-vbus-default-pins {
+		pins-vbus {
+			pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>;
+			input-enable;
+		};
+	};
+
 	uart0_pins: uart0-pins {
 		pins {
 			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
@@ -885,8 +962,31 @@  &ufsphy {
 };
 
 &ssusb0 {
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&u3_p0_vbus>;
+	usb-role-switch;
 	vusb33-supply = <&mt6359_vusb_ldo_reg>;
 	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			mtu3_hs0_role_sw: endpoint {
+				remote-endpoint = <&typec_con_hs>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			mtu3_ss0_role_sw: endpoint {
+				remote-endpoint = <&typec_con_ss>;
+			};
+		};
+	};
 };
 
 &ssusb2 {