| Message ID | 1481032253-27019-1-git-send-email-linus.walleij@linaro.org |
|---|---|
| State | New |
| Headers | show |
> This adds the device tree bindings for the Qualcomm PM8xxx > ADCs. This is based on the existing DT bindings for the > SPMI ADC so there are hopefully no controversial features. nitpicking below > Cc: devicetree@vger.kernel.org > Cc: linux-arm-kernel@lists.infradead.org > Cc: linux-arm-msm@vger.kernel.org > Cc: Ivan T. Ivanov <iivanov.xz@gmail.com> > Cc: Andy Gross <andy.gross@linaro.org> > Cc: Bjorn Andersson <bjorn.andersson@linaro.org> > Cc: Stephen Boyd <sboyd@codeaurora.org> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > .../bindings/iio/adc/qcom,pm8xxx-xoadc.txt | 160 +++++++++++++++++++++ > 1 file changed, 160 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt > > diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt > new file mode 100644 > index 000000000000..6e51e3e74b88 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt > @@ -0,0 +1,160 @@ > +Qualcomm's PM8xxx voltage XOADC > + > +The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Chrystal crystal > +oscillator ADC) encompass PM8018, PM8038, PM8058, PM8917 and PM8921. encompassing > + > +Required properties: > + > +- compatible: should be one of: > + "qcom,pm8018-adc" > + "qcom,pm8038-adc" > + "qcom,pm8058-adc" > + "qcom,pm8917-adc" > + "qcom,pm8921-adc" > + > +- reg: should contain the ADC base address in the PMIC, typically > + 0x197. > + > +The following required properties are standard for IO channels, see > +iio-bindings.txt for more details: > + > +- #address-cells: should be set to <1> > + > +- #size-cells: should be set to <0> > + > +- #io-channel-cells: should be set to <1> > + > +- interrupts: should refer to the parent PMIC interrupt controller > + and reference the proper ADC interrupt. > + > +Required subnodes: > + > +The ADC channels are configured as subnodes of the ADC. Since some of > +them are used for calibrating the ADC, these nodes are compulsory: > + > +ref_625mv { > + reg = <0x0c>; > +}; > + > +ref_1250mv { > + reg = <0x0d>; > +}; > + > +ref_muxoff { > + reg = <0x0f>; > +}; > + > +These three nodes are used for absolute and ratiometric calibration > +and only need to have these reg values: they are by hardware defined they are by hardware definition 1:1 ratio converters that sample ... > +to be 1:1 ratio converters that sample 625, 1250 and 0 V and create milliV or 0.625, 1.250 V > +an interpolation calibration for all other ADCs. > + > +Optional subnodes: any channels other than channel 0x0c, 0x0d and > +0x0f are optional. > + > +Required channel node properties: > + > +- reg: should contain the hardware channel number in the range > + 0 .. 0x0f (4 bits). The hardware only supports 16 channels. > + > +Optional channel node properties: > + > +- qcom,decimation: > + Value type: <u32> > + Definition: This parameter is used to decrease ADC sampling rate. > + Quicker measurements can be made by reducing decimation ratio. > + Valid values are 512, 1024, 2048, 4096. > + If property is not found, default value of 512 will be used. > + > +- qcom,ratiometric: > + Value type: <empty> > + Definition: Channel calibration type. If this property is specified > + VADC will use the VDD reference (1.8V) and GND for channel > + calibration. If property is not found, channel will be > + calibrated with 0.625V and 1.25V reference channels, also > + known as absolute calibration. > + > +- qcom,ratiometric-ref: > + Value type: <u32> > + Definition: The reference voltage pair when using ratiometric > + calibration: > + 0 = XO_IN/XOADC_GND > + 1 = PMIC_IN/XOADC_GND > + 2 = PMIC_IN/BMS_CSP > + 3 (invalid) > + 4 = XOADC_GND/XOADC_GND > + 5 = XOADC_VREF/XOADC_GND > + > +Example: > + > +xoadc: xoadc@197 { > + compatible = "qcom,pm8058-adc"; > + reg = <0x197>; > + interrupt-parent = <&pm8058>; > + interrupts = <76 1>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + > + vcoin { > + reg = <0x00>; > + }; > + vbat { > + reg = <0x01>; > + }; > + dcin { > + reg = <0x02>; > + }; > + ichg { > + reg = <0x03>; > + }; > + vph_pwr { > + reg = <0x04>; > + }; > + mpp5 { > + reg = <0x05>; > + }; > + mpp6 { > + reg = <0x06>; > + }; > + mpp7 { > + reg = <0x07>; > + }; > + mpp8 { > + reg = <0x08>; > + }; > + mpp9 { > + reg = <0x09>; > + }; > + usb_vbus { > + reg = <0x0a>; > + }; > + die_temp { > + reg = <0x0b>; > + }; > + ref_625mv { > + reg = <0x0c>; > + }; > + ref_1250mv { > + reg = <0x0d>; > + }; > + ref_325mv { > + reg = <0x0e>; > + }; > + ref_muxoff { > + reg = <0x0f>; > + }; > +}; > + > + > +/* IIO client node */ > +iio-hwmon { > + compatible = "iio-hwmon"; > + io-channels = <&xoadc 0x01>, /* Battery */ > + <&xoadc 0x02>, /* DC in (charger) */ > + <&xoadc 0x04>, /* VPH the main system voltage */ > + <&xoadc 0x0b>, /* Die temperature */ > + <&xoadc 0x0c>, /* Reference voltage 1.25V */ > + <&xoadc 0x0d>, /* Reference voltage 0.625V */ > + <&xoadc 0x0e>; /* Reference voltage 0.325V */ > +}; > -- Peter Meerwald-Stadler +43-664-2444418 (mobile) -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt new file mode 100644 index 000000000000..6e51e3e74b88 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt @@ -0,0 +1,160 @@ +Qualcomm's PM8xxx voltage XOADC + +The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Chrystal +oscillator ADC) encompass PM8018, PM8038, PM8058, PM8917 and PM8921. + +Required properties: + +- compatible: should be one of: + "qcom,pm8018-adc" + "qcom,pm8038-adc" + "qcom,pm8058-adc" + "qcom,pm8917-adc" + "qcom,pm8921-adc" + +- reg: should contain the ADC base address in the PMIC, typically + 0x197. + +The following required properties are standard for IO channels, see +iio-bindings.txt for more details: + +- #address-cells: should be set to <1> + +- #size-cells: should be set to <0> + +- #io-channel-cells: should be set to <1> + +- interrupts: should refer to the parent PMIC interrupt controller + and reference the proper ADC interrupt. + +Required subnodes: + +The ADC channels are configured as subnodes of the ADC. Since some of +them are used for calibrating the ADC, these nodes are compulsory: + +ref_625mv { + reg = <0x0c>; +}; + +ref_1250mv { + reg = <0x0d>; +}; + +ref_muxoff { + reg = <0x0f>; +}; + +These three nodes are used for absolute and ratiometric calibration +and only need to have these reg values: they are by hardware defined +to be 1:1 ratio converters that sample 625, 1250 and 0 V and create +an interpolation calibration for all other ADCs. + +Optional subnodes: any channels other than channel 0x0c, 0x0d and +0x0f are optional. + +Required channel node properties: + +- reg: should contain the hardware channel number in the range + 0 .. 0x0f (4 bits). The hardware only supports 16 channels. + +Optional channel node properties: + +- qcom,decimation: + Value type: <u32> + Definition: This parameter is used to decrease ADC sampling rate. + Quicker measurements can be made by reducing decimation ratio. + Valid values are 512, 1024, 2048, 4096. + If property is not found, default value of 512 will be used. + +- qcom,ratiometric: + Value type: <empty> + Definition: Channel calibration type. If this property is specified + VADC will use the VDD reference (1.8V) and GND for channel + calibration. If property is not found, channel will be + calibrated with 0.625V and 1.25V reference channels, also + known as absolute calibration. + +- qcom,ratiometric-ref: + Value type: <u32> + Definition: The reference voltage pair when using ratiometric + calibration: + 0 = XO_IN/XOADC_GND + 1 = PMIC_IN/XOADC_GND + 2 = PMIC_IN/BMS_CSP + 3 (invalid) + 4 = XOADC_GND/XOADC_GND + 5 = XOADC_VREF/XOADC_GND + +Example: + +xoadc: xoadc@197 { + compatible = "qcom,pm8058-adc"; + reg = <0x197>; + interrupt-parent = <&pm8058>; + interrupts = <76 1>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + vcoin { + reg = <0x00>; + }; + vbat { + reg = <0x01>; + }; + dcin { + reg = <0x02>; + }; + ichg { + reg = <0x03>; + }; + vph_pwr { + reg = <0x04>; + }; + mpp5 { + reg = <0x05>; + }; + mpp6 { + reg = <0x06>; + }; + mpp7 { + reg = <0x07>; + }; + mpp8 { + reg = <0x08>; + }; + mpp9 { + reg = <0x09>; + }; + usb_vbus { + reg = <0x0a>; + }; + die_temp { + reg = <0x0b>; + }; + ref_625mv { + reg = <0x0c>; + }; + ref_1250mv { + reg = <0x0d>; + }; + ref_325mv { + reg = <0x0e>; + }; + ref_muxoff { + reg = <0x0f>; + }; +}; + + +/* IIO client node */ +iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&xoadc 0x01>, /* Battery */ + <&xoadc 0x02>, /* DC in (charger) */ + <&xoadc 0x04>, /* VPH the main system voltage */ + <&xoadc 0x0b>, /* Die temperature */ + <&xoadc 0x0c>, /* Reference voltage 1.25V */ + <&xoadc 0x0d>, /* Reference voltage 0.625V */ + <&xoadc 0x0e>; /* Reference voltage 0.325V */ +};
This adds the device tree bindings for the Qualcomm PM8xxx ADCs. This is based on the existing DT bindings for the SPMI ADC so there are hopefully no controversial features. Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: Ivan T. Ivanov <iivanov.xz@gmail.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- .../bindings/iio/adc/qcom,pm8xxx-xoadc.txt | 160 +++++++++++++++++++++ 1 file changed, 160 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,pm8xxx-xoadc.txt -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html