new file mode 100644
@@ -0,0 +1,543 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/adi,ad4170.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD4170 and similar Analog to Digital Converters
+
+maintainers:
+ - Marcelo Schmitt <marcelo.schmitt@analog.com>
+
+description: |
+ Analog Devices AD4170 series of Sigma-delta Analog to Digital Converters.
+ Specifications can be found at:
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4170-4.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4190-4.pdf
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad4195-4.pdf
+
+$ref: /schemas/spi/spi-peripheral-props.yaml#
+
+$defs:
+ reference-buffer:
+ description: |
+ Enable precharge buffer, full buffer, or skip reference buffering of
+ the positive/negative voltage reference. Because the output impedance
+ of the source driving the voltage reference inputs may be dynamic, RC
+ combinations of those inputs can cause DC gain errors if the reference
+ inputs go unbuffered into the ADC. Enable reference buffering if the
+ provided reference source has dynamic high impedance output. Note the
+ absolute voltage allowed on REFINn+ and REFINn- inputs is from
+ AVSS - 50 mV to AVDD + 50 mV when the reference buffers are disabled
+ but narrows to AVSS to AVDD when reference buffering is enabled or in
+ precharge mode. The valid options for this property are:
+ 0: Reference precharge buffer.
+ 1: Full reference buffering.
+ 2: Bypass reference buffers (buffering disabled).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+ default: 1
+
+ excitation-pin:
+ description: |
+ Analog input to apply excitation current to while the channel
+ is active.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 20
+
+properties:
+ compatible:
+ enum:
+ - adi,ad4170
+ - adi,ad4190
+ - adi,ad4195
+
+ avss-supply:
+ description:
+ Reference voltage supply for AVSS. If provided, describes the magnitude
+ (absolute value) of the negative voltage supplied to the AVSS pin. Since
+ AVSS must be −2.625V minimum and 0V maximum, the declared supply voltage
+ must be between 0 and 2.65V. If not provided, AVSS is assumed to be at
+ system ground (0V).
+
+ avdd-supply:
+ description:
+ A supply of 4.75V to 5.25V relative to AVSS that powers the chip (AVDD).
+
+ iovdd-supply:
+ description: 1.7V to 5.25V reference supply to the serial interface (IOVDD).
+
+ refin1p-supply:
+ description: REFIN+ supply that can be used as reference for conversion.
+
+ refin1n-supply:
+ description: REFIN- supply that can be used as reference for conversion. If
+ provided, describes the magnitude (absolute value) of the negative voltage
+ supplied to the REFIN- pin.
+
+ refin2p-supply:
+ description: REFIN2+ supply that can be used as reference for conversion.
+
+ refin2n-supply:
+ description: REFIN2- supply that can be used as reference for conversion. If
+ provided, describes the magnitude (absolute value) of the negative voltage
+ supplied to the REFIN2- pin.
+
+ spi-cpol: true
+
+ spi-cpha: true
+
+ interrupts:
+ description:
+ Interrupt for signaling the completion of conversion results. The data
+ ready signal (RDY) used as interrupt is by default provided on the SDO
+ pin. Alternatively, it can be provided on the DIG_AUX1 pin in which case
+ the chip disables the RDY function on SDO. Thus, there can be only one
+ data ready interrupt enabled at a time.
+ maxItems: 1
+
+ interrupt-names:
+ description:
+ Specify which pin should be configured as Data Ready interrupt.
+ enum:
+ - sdo
+ - dig_aux1
+ maxItems: 1
+ default: sdo
+
+ clocks:
+ maxItems: 1
+ description:
+ Optional external clock source. Can specify either an external clock or
+ external crystal.
+
+ clock-names:
+ enum:
+ - ext-clk
+ - xtal
+ default: ext-clk
+
+ '#clock-cells':
+ const: 0
+
+ clock-output-names:
+ maxItems: 1
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ The first cell is for the GPIO number: 0 to 3.
+ The second cell takes standard GPIO flags.
+
+ ldac-gpios:
+ description:
+ GPIO connected to DIG_AUX2 pin to be used as LDAC toggle to control the
+ transfer of data from the DAC_INPUT_A register to the DAC.
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ adi,vbias-pins:
+ description: Analog inputs to apply a voltage bias of (AVDD − AVSS) / 2 to.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 9
+ items:
+ minimum: 0
+ maximum: 8
+
+allOf:
+ # Some devices don't have integrated DAC
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - adi,ad4190
+ - adi,ad4195
+ then:
+ properties:
+ ldac-gpios: false
+
+ # If an external clock is set, the internal clock cannot go out and vice versa
+ - oneOf:
+ - required: [clocks]
+ properties:
+ '#clock-cells': false
+ - required: ['#clock-cells']
+ properties:
+ clocks: false
+
+patternProperties:
+ "^channel@[0-9a-f]$":
+ $ref: /schemas/iio/adc/adc.yaml#
+ unevaluatedProperties: false
+ description:
+ Represents the external channels which are connected to the ADC.
+
+ properties:
+ reg:
+ description:
+ The channel number.
+ minimum: 0
+ maximum: 15
+
+ diff-channels:
+ description: |
+ This property is used for defining the inputs of a differential
+ voltage channel. The first value is the positive input and the second
+ value is the negative input of the channel.
+
+ Besides the analog input pins AIN0 to AIN8, there are special inputs
+ that can be selected with the following values:
+ 17: Internal temperature sensor
+ 18: (AVDD-AVSS)/5
+ 19: (IOVDD-DGND)/5
+ 20: DAC output
+ 21: ALDO
+ 22: DLDO
+ 23: AVSS
+ 24: DGND
+ 25: REFIN+
+ 26: REFIN-
+ 27: REFIN2+
+ 28: REFIN2-
+ 29: REFOUT
+ For the internal temperature sensor, use the input number for both
+ inputs (i.e. diff-channels = <17 17>).
+ items:
+ enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 17, 18, 19, 20, 21, 22, 23, 24, 25,
+ 26, 27, 28, 29]
+
+ adi,reference-select:
+ description: |
+ Select the reference source to use when converting on the
+ specific channel. Valid values are:
+ 0: REFIN+/REFIN-
+ 1: REFIN2+/REFIN2−
+ 2: REFOUT/AVSS (internal reference)
+ 3: AVDD/AVSS
+ If not specified, REFOUT/AVSS is used.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 1
+
+ adi,positive-reference-buffer:
+ $ref: '#/$defs/reference-buffer'
+
+ adi,negative-reference-buffer:
+ $ref: '#/$defs/reference-buffer'
+
+ adi,sensor-type:
+ description:
+ The AD4170 and similar designs have features to aid interfacing with
+ load cell weigh scale, RTD, and thermocouple sensors. Each of those
+ sensor types requires either distinct wiring configuration or
+ external circuitry for proper sensor operation and can use different
+ ADC chip functionality on their setups. A key characteristic of those
+ external sensors is that they must be excited either by voltage supply
+ or by ADC chip excitation signals. The sensor can then be read through
+ a pair of analog inputs. This property specifies which particular
+ sensor type is connected to the ADC so it can be properly setup and
+ handled. Omit this property for conventional (not weigh scale, RTD, or
+ thermocouple) ADC channel setups.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [ weighscale, rtd, thermocouple ]
+
+ adi,excitation-pin-0:
+ $ref: '#/$defs/excitation-pin'
+
+ adi,excitation-pin-1:
+ $ref: '#/$defs/excitation-pin'
+
+ adi,excitation-pin-2:
+ $ref: '#/$defs/excitation-pin'
+
+ adi,excitation-pin-3:
+ $ref: '#/$defs/excitation-pin'
+
+ adi,excitation-current-0-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-0 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-1-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-1 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-2-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-2 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-current-3-microamp:
+ description:
+ Excitation current in microamperes to be applied to pin specified in
+ adi,excitation-pin-3 while this channel is active.
+ enum: [0, 10, 50, 100, 250, 500, 1000, 1500]
+ default: 0
+
+ adi,excitation-ac:
+ type: boolean
+ description:
+ Whether the external sensor has to be AC or DC excited. When omitted,
+ it is DC excited.
+
+ allOf:
+ - oneOf:
+ - required: [single-channel, common-mode-channel]
+ properties:
+ diff-channels: false
+ - required: [diff-channels]
+ properties:
+ single-channel: false
+ common-mode-channel: false
+ # Usual ADC channels don't need external circuitry excitation.
+ - if:
+ not:
+ required:
+ - adi,sensor-type
+ then:
+ properties:
+ adi,excitation-pin-0: false
+ adi,excitation-pin-1: false
+ adi,excitation-pin-2: false
+ adi,excitation-pin-3: false
+ adi,excitation-current-0-microamp: false
+ adi,excitation-current-1-microamp: false
+ adi,excitation-current-2-microamp: false
+ adi,excitation-current-3-microamp: false
+ adi,excitation-ac: false
+ # Weigh scale bridge AC excited with one pair of predefined signals.
+ - if:
+ allOf:
+ - properties:
+ adi,sensor-type:
+ contains:
+ const: weighscale
+ - required:
+ - adi,excitation-ac
+ - adi,excitation-pin-2
+ - adi,excitation-pin-3
+ - not:
+ required:
+ - adi,excitation-current-2-microamp
+ - adi,excitation-current-3-microamp
+ then:
+ properties:
+ adi,excitation-pin-2:
+ const: 19
+ adi,excitation-pin-3:
+ const: 20
+ # Weigh scale bridge AC excited with two pairs of predefined signals.
+ - if:
+ allOf:
+ - properties:
+ adi,sensor-type:
+ contains:
+ const: weighscale
+ - required:
+ - adi,excitation-ac
+ - adi,excitation-pin-0
+ - adi,excitation-pin-1
+ - adi,excitation-pin-2
+ - adi,excitation-pin-3
+ - not:
+ required:
+ - adi,excitation-current-0-microamp
+ - adi,excitation-current-1-microamp
+ - adi,excitation-current-2-microamp
+ - adi,excitation-current-3-microamp
+ then:
+ properties:
+ adi,excitation-pin-0:
+ const: 17
+ adi,excitation-pin-1:
+ const: 18
+ adi,excitation-pin-2:
+ const: 19
+ adi,excitation-pin-3:
+ const: 20
+
+required:
+ - compatible
+ - reg
+ - avdd-supply
+ - iovdd-supply
+ - spi-cpol
+ - spi-cpha
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4170";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpol;
+ spi-cpha;
+ avdd-supply = <&avdd>;
+ iovdd-supply = <&iovdd>;
+ clocks = <&clk>;
+ clock-names = "xtal";
+ interrupt-parent = <&gpio_in>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ adi,vbias-pins = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // Sample AIN0 with respect to DGND throughout AVDD/DGND input range
+ // Pseudo-differential unipolar
+ channel@0 {
+ reg = <0>;
+ single-channel = <0>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Weigh scale sensor
+ channel@1 {
+ reg = <1>;
+ bipolar;
+ diff-channels = <1 2>;
+ adi,reference-select = <0>;
+ adi,positive-reference-buffer = <0>;
+ adi,negative-reference-buffer = <0>;
+ adi,sensor-type = "weighscale";
+ adi,excitation-pin-2 = <19>;
+ adi,excitation-pin-3 = <20>;
+ adi,excitation-ac;
+ };
+ // RTD sensor
+ channel@2 {
+ reg = <2>;
+ bipolar;
+ diff-channels = <3 4>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "rtd";
+ adi,excitation-pin-0 = <5>;
+ adi,excitation-pin-1 = <6>;
+ adi,excitation-current-0-microamp = <500>;
+ adi,excitation-current-1-microamp = <500>;
+ adi,excitation-ac;
+ };
+ // Thermocouple sensor
+ channel@3 {
+ reg = <3>;
+ bipolar;
+ diff-channels = <7 8>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "thermocouple";
+ adi,excitation-pin-0 = <18>;
+ adi,excitation-current-0-microamp = <500>;
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "adi,ad4170";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpol;
+ spi-cpha;
+ avdd-supply = <&avdd>;
+ iovdd-supply = <&iovdd>;
+ #clock-cells = <0>;
+ clock-output-names = "ad4170-clk16mhz";
+ interrupt-parent = <&gpio_in>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ // Sample AIN0 with respect to AIN1 throughout AVDD/AVSS input range
+ // Differential bipolar. If AVSS < 0V, differential true bipolar
+ channel@0 {
+ reg = <0>;
+ bipolar;
+ diff-channels = <0 1>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN2 with respect to DGND throughout AVDD/DGND input range
+ // Pseudo-differential unipolar
+ channel@1 {
+ reg = <1>;
+ single-channel = <2>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN3 with respect to 2.5V throughout AVDD/AVSS input range
+ // Pseudo-differential bipolar
+ channel@2 {
+ reg = <2>;
+ bipolar;
+ single-channel = <3>;
+ common-mode-channel = <29>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN4 with respect to DGND throughout AVDD/AVSS input range
+ // Pseudo-differential bipolar
+ channel@3 {
+ reg = <3>;
+ bipolar;
+ single-channel = <4>;
+ common-mode-channel = <24>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN5 with respect to 2.5V throughout AVDD/AVSS input range
+ // Pseudo-differential unipolar (AD4170 datasheet page 46 example)
+ channel@4 {
+ reg = <4>;
+ single-channel = <5>;
+ common-mode-channel = <29>;
+ adi,reference-select = <3>;
+ };
+ // Sample AIN6 with respect to 2.5V throughout REFIN+/REFIN- input range
+ // Pseudo-differential bipolar
+ channel@5 {
+ reg = <5>;
+ bipolar;
+ single-channel = <6>;
+ common-mode-channel = <29>;
+ adi,reference-select = <0>;
+ };
+ // Weigh scale sensor
+ channel@6 {
+ reg = <6>;
+ bipolar;
+ diff-channels = <7 8>;
+ adi,reference-select = <0>;
+ adi,sensor-type = "weighscale";
+ adi,excitation-pin-0 = <17>;
+ adi,excitation-pin-1 = <18>;
+ adi,excitation-pin-2 = <19>;
+ adi,excitation-pin-3 = <20>;
+ adi,excitation-ac;
+ };
+ };
+ };
+...
+
@@ -1354,6 +1354,13 @@ F: Documentation/ABI/testing/sysfs-bus-iio-adc-ad4130
F: Documentation/devicetree/bindings/iio/adc/adi,ad4130.yaml
F: drivers/iio/adc/ad4130.c
+ANALOG DEVICES INC AD4170 DRIVER
+M: Marcelo Schmitt <marcelo.schmitt@analog.com>
+L: linux-iio@vger.kernel.org
+S: Supported
+W: https://ez.analog.com/linux-software-drivers
+F: Documentation/devicetree/bindings/iio/adc/adi,ad4170.yaml
+
ANALOG DEVICES INC AD4695 DRIVER
M: Michael Hennerich <michael.hennerich@analog.com>
M: Nuno Sá <nuno.sa@analog.com>
Add device tree documentation for AD4170 and similar sigma-delta ADCs. The AD4170 is a 24-bit, multichannel, sigma-delta ADC. Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com> --- Change log v3 -> v4 - Dropped sensor-node and most of defs. - Updated external sensor props to have similar name and type of adi,ad4130 ones. - Added constraints to properties related to external bridge sensor excitation. Some explanation about the constraints to weigh scale sensor types. The predefined ACX1, ACX1 negated, ACX2, and ACX2 negated signals are used to AC excite external bridge circuits and are output on GPIO2, GPIO0, GPIO3, and GPIO1, respectively. If only two pins are specified for AC excitation, only ACX1 and ACX2 (GPIO2 and GPIO3) are used. Because of that, if AC excitation is specified/requested, then those specific GPIO pins must be used with the bridge. Otherwise, the bridge won't get properly excited and we also cannot guarantee to avoid short-circuit conditions since the level set to GPIOs to DC excite the bridge depends on the GPIO number. See AD4170 datasheet Figure 113 Weigh Scale (AC Excitation) for the reference circuit diagram. Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad4170-4.pdf#unique_149_Connect_42_ID10354 .../bindings/iio/adc/adi,ad4170.yaml | 543 ++++++++++++++++++ MAINTAINERS | 7 + 2 files changed, 550 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad4170.yaml