| Message ID | 06154a2280a8423af80405825d7201c7aa927696.1488374335.git.jerome.forissier@linaro.org |
|---|---|
| State | New |
| Headers | show |
On Wed, Mar 1, 2017 at 7:29 AM, Jerome Forissier <jerome.forissier@linaro.org> wrote: > Some platforms may use a single device tree to describe two address > spaces, as described in d9f43babb998 ("Documentation: dt: Add bindings > for Secure-only devices"). We extend the use of the secure- prefix to > the stdout-path property, so that the Secure firmware may use a > different console device than the one used by the kernel. > > Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> > --- > Documentation/devicetree/bindings/arm/secure.txt | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt > index e31303f..558c9a1 100644 > --- a/Documentation/devicetree/bindings/arm/secure.txt > +++ b/Documentation/devicetree/bindings/arm/secure.txt > @@ -51,3 +51,8 @@ Valid Secure world properties: > status = "disabled"; secure-status = "okay"; /* S-only */ > status = "disabled"; /* disabled in both */ > status = "disabled"; secure-status = "disabled"; /* disabled in both */ > + > +- secure-stdout-path (/chosen node): specifies the device to be used > +for console output by Secure firmware. The syntax is the same as for > +"stdout-path". If "secure-stdout-path" is not specified it defaults to > +the same value as "stdout-path". I'm not all that enthusiastic about this. This alone is okay, but continued additions of secure-* properties doesn't seem very scalable. Is this it or do you have other needs? What happens when we have 3 modes/address spaces? Maybe we should allow stdout-path to have multiple strings and secure fw grabs the first one and updates the DT removing it (perhaps only if the device is secure only). Might be nice to have multiple ones supported anyway (like we can do on the kernel command line: "console=ttyS0 console=ttyS1"). Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 03/01/2017 03:50 PM, Rob Herring wrote: > On Wed, Mar 1, 2017 at 7:29 AM, Jerome Forissier > <jerome.forissier@linaro.org> wrote: >> Some platforms may use a single device tree to describe two address >> spaces, as described in d9f43babb998 ("Documentation: dt: Add bindings >> for Secure-only devices"). We extend the use of the secure- prefix to >> the stdout-path property, so that the Secure firmware may use a >> different console device than the one used by the kernel. >> >> Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> >> --- >> Documentation/devicetree/bindings/arm/secure.txt | 5 +++++ >> 1 file changed, 5 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt >> index e31303f..558c9a1 100644 >> --- a/Documentation/devicetree/bindings/arm/secure.txt >> +++ b/Documentation/devicetree/bindings/arm/secure.txt >> @@ -51,3 +51,8 @@ Valid Secure world properties: >> status = "disabled"; secure-status = "okay"; /* S-only */ >> status = "disabled"; /* disabled in both */ >> status = "disabled"; secure-status = "disabled"; /* disabled in both */ >> + >> +- secure-stdout-path (/chosen node): specifies the device to be used >> +for console output by Secure firmware. The syntax is the same as for >> +"stdout-path". If "secure-stdout-path" is not specified it defaults to >> +the same value as "stdout-path". > > I'm not all that enthusiastic about this. This alone is okay, but > continued additions of secure-* properties doesn't seem very scalable. > Is this it or do you have other needs? What happens when we have 3 > modes/address spaces? How is this different from status/secure-status? I have no other needs for the moment. I'm experimenting with the introduction of DT in OP-TEE. The secure-status property (or lack thereof) already allows me to know if a device can be used by the secure OS and how it should be mapped (secure vs. non-secure). This extension allows me to reuse the same TEE binary and change the console, which is a simple use case to demonstrate the advantage of using the DT in the secure FW. > Maybe we should allow stdout-path to have multiple strings and secure > fw grabs the first one and updates the DT removing it (perhaps only if > the device is secure only). Might be nice to have multiple ones > supported anyway (like we can do on the kernel command line: > "console=ttyS0 console=ttyS1"). The problem I see with removing entries is that the secure firmware may have multiple stages (say, ARM Trusted Firmware plus a secure OS such as OP-TEE). Thanks, -- Jerome -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 01/03/17 15:04, Jerome Forissier wrote: > > > On 03/01/2017 03:50 PM, Rob Herring wrote: >> On Wed, Mar 1, 2017 at 7:29 AM, Jerome Forissier >> <jerome.forissier@linaro.org> wrote: >>> Some platforms may use a single device tree to describe two address >>> spaces, as described in d9f43babb998 ("Documentation: dt: Add bindings >>> for Secure-only devices"). We extend the use of the secure- prefix to >>> the stdout-path property, so that the Secure firmware may use a >>> different console device than the one used by the kernel. >>> >>> Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> >>> --- >>> Documentation/devicetree/bindings/arm/secure.txt | 5 +++++ >>> 1 file changed, 5 insertions(+) >>> >>> diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt >>> index e31303f..558c9a1 100644 >>> --- a/Documentation/devicetree/bindings/arm/secure.txt >>> +++ b/Documentation/devicetree/bindings/arm/secure.txt >>> @@ -51,3 +51,8 @@ Valid Secure world properties: >>> status = "disabled"; secure-status = "okay"; /* S-only */ >>> status = "disabled"; /* disabled in both */ >>> status = "disabled"; secure-status = "disabled"; /* disabled in both */ >>> + >>> +- secure-stdout-path (/chosen node): specifies the device to be used >>> +for console output by Secure firmware. The syntax is the same as for >>> +"stdout-path". If "secure-stdout-path" is not specified it defaults to >>> +the same value as "stdout-path". >> >> I'm not all that enthusiastic about this. This alone is okay, but >> continued additions of secure-* properties doesn't seem very scalable. >> Is this it or do you have other needs? What happens when we have 3 >> modes/address spaces? > > How is this different from status/secure-status? > I have no other needs for the moment. I'm experimenting with the > introduction of DT in OP-TEE. The secure-status property (or lack > thereof) already allows me to know if a device can be used by the secure > OS and how it should be mapped (secure vs. non-secure). This extension > allows me to reuse the same TEE binary and change the console, which is > a simple use case to demonstrate the advantage of using the DT in the > secure FW. Once you start using DT in the secure OS, it doesn't seem too big a leap for folks to want to start passing arguments, so I'd consider secure-bootargs to be almost inevitable at *some* point down this road. Perhaps we should consider a /secure-chosen node containing standard properties instead... >> Maybe we should allow stdout-path to have multiple strings and secure >> fw grabs the first one and updates the DT removing it (perhaps only if >> the device is secure only). Might be nice to have multiple ones >> supported anyway (like we can do on the kernel command line: >> "console=ttyS0 console=ttyS1"). > > The problem I see with removing entries is that the secure firmware may > have multiple stages (say, ARM Trusted Firmware plus a secure OS such as > OP-TEE). ...which different elements of firmware would in theory have a lot more freedom to mangle between boot stages without the risk of disrupting the regular /chosen properties. Robin. > > Thanks, > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 03/01/2017 04:20 PM, Robin Murphy wrote: > On 01/03/17 15:04, Jerome Forissier wrote: >> >> >> On 03/01/2017 03:50 PM, Rob Herring wrote: >>> On Wed, Mar 1, 2017 at 7:29 AM, Jerome Forissier >>> <jerome.forissier@linaro.org> wrote: >>>> Some platforms may use a single device tree to describe two address >>>> spaces, as described in d9f43babb998 ("Documentation: dt: Add bindings >>>> for Secure-only devices"). We extend the use of the secure- prefix to >>>> the stdout-path property, so that the Secure firmware may use a >>>> different console device than the one used by the kernel. >>>> >>>> Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> >>>> --- >>>> Documentation/devicetree/bindings/arm/secure.txt | 5 +++++ >>>> 1 file changed, 5 insertions(+) >>>> >>>> diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt >>>> index e31303f..558c9a1 100644 >>>> --- a/Documentation/devicetree/bindings/arm/secure.txt >>>> +++ b/Documentation/devicetree/bindings/arm/secure.txt >>>> @@ -51,3 +51,8 @@ Valid Secure world properties: >>>> status = "disabled"; secure-status = "okay"; /* S-only */ >>>> status = "disabled"; /* disabled in both */ >>>> status = "disabled"; secure-status = "disabled"; /* disabled in both */ >>>> + >>>> +- secure-stdout-path (/chosen node): specifies the device to be used >>>> +for console output by Secure firmware. The syntax is the same as for >>>> +"stdout-path". If "secure-stdout-path" is not specified it defaults to >>>> +the same value as "stdout-path". >>> >>> I'm not all that enthusiastic about this. This alone is okay, but >>> continued additions of secure-* properties doesn't seem very scalable. >>> Is this it or do you have other needs? What happens when we have 3 >>> modes/address spaces? >> >> How is this different from status/secure-status? >> I have no other needs for the moment. I'm experimenting with the >> introduction of DT in OP-TEE. The secure-status property (or lack >> thereof) already allows me to know if a device can be used by the secure >> OS and how it should be mapped (secure vs. non-secure). This extension >> allows me to reuse the same TEE binary and change the console, which is >> a simple use case to demonstrate the advantage of using the DT in the >> secure FW. > > Once you start using DT in the secure OS, it doesn't seem too big a leap > for folks to want to start passing arguments, so I'd consider > secure-bootargs to be almost inevitable at *some* point down this road. > > Perhaps we should consider a /secure-chosen node containing standard > properties instead... Fine with me. I'll send a new patch. >>> Maybe we should allow stdout-path to have multiple strings and secure >>> fw grabs the first one and updates the DT removing it (perhaps only if >>> the device is secure only). Might be nice to have multiple ones >>> supported anyway (like we can do on the kernel command line: >>> "console=ttyS0 console=ttyS1"). >> >> The problem I see with removing entries is that the secure firmware may >> have multiple stages (say, ARM Trusted Firmware plus a secure OS such as >> OP-TEE). > > ...which different elements of firmware would in theory have a lot more > freedom to mangle between boot stages without the risk of disrupting the > regular /chosen properties. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt index e31303f..558c9a1 100644 --- a/Documentation/devicetree/bindings/arm/secure.txt +++ b/Documentation/devicetree/bindings/arm/secure.txt @@ -51,3 +51,8 @@ Valid Secure world properties: status = "disabled"; secure-status = "okay"; /* S-only */ status = "disabled"; /* disabled in both */ status = "disabled"; secure-status = "disabled"; /* disabled in both */ + +- secure-stdout-path (/chosen node): specifies the device to be used +for console output by Secure firmware. The syntax is the same as for +"stdout-path". If "secure-stdout-path" is not specified it defaults to +the same value as "stdout-path".
Some platforms may use a single device tree to describe two address spaces, as described in d9f43babb998 ("Documentation: dt: Add bindings for Secure-only devices"). We extend the use of the secure- prefix to the stdout-path property, so that the Secure firmware may use a different console device than the one used by the kernel. Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> --- Documentation/devicetree/bindings/arm/secure.txt | 5 +++++ 1 file changed, 5 insertions(+) -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html