| Message ID | 20230117024846.1367794-1-bryan.odonoghue@linaro.org |
|---|---|
| Headers | show |
| Series | Add MSM8939 SoC support with two devices | expand |
On Tue, 17 Jan 2023 02:48:38 +0000, Bryan O'Donoghue wrote: > V3: > - Happily I don't currently depend on any other series to be merged. > Bjorn and Chanwoo picked up everything I need to unblock this series. ＼(^o^)／ > > - Moves xo_board to RPM/PMIC clock gated CXO, not including rpmcc: obvs - Konrad/Bjorn > - qcom,msm-id = <239 0> - left as in V2 valid according to Sony references - bod > - cpu-release-addr - as stated below we rely on lk2nd to take the second cluster > out of reset - bod > - smem child node update - Konrad > - Whitespace updates - Konrad > - gpu no interconnect - Konrad - No bod > - 19.2 MHz dropped from timer@b020000 - Konrad > - Added vreg_dummy comment - Konrad > - sdc_pins grouped - Konrad > - startup-delay-us = <0> - left as is > - bias - added no-bias - Konrad > - :g/msmgpio/s//tlmm/g - Konrad > - mdss/s//display-controller - Konrad > - l11 set-load - Korad > > [...] Applied, thanks! [4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* commit: d03de4179540e9cee6e3f664e1b65178f07bb612 Best regards,
V3: - Happily I don't currently depend on any other series to be merged. Bjorn and Chanwoo picked up everything I need to unblock this series. ＼(^o^)／ - Moves xo_board to RPM/PMIC clock gated CXO, not including rpmcc: obvs - Konrad/Bjorn - qcom,msm-id = <239 0> - left as in V2 valid according to Sony references - bod - cpu-release-addr - as stated below we rely on lk2nd to take the second cluster out of reset - bod - smem child node update - Konrad - Whitespace updates - Konrad - gpu no interconnect - Konrad - No bod - 19.2 MHz dropped from timer@b020000 - Konrad - Added vreg_dummy comment - Konrad - sdc_pins grouped - Konrad - startup-delay-us = <0> - left as is - bias - added no-bias - Konrad - :g/msmgpio/s//tlmm/g - Konrad - mdss/s//display-controller - Konrad - l11 set-load - Korad - l12 upper voltage raised to 3.3v since this is what the downstream kernel says when I boot and interrogate it - bod - sdhc@address - Discussed with Krzysztof and implemented as discussed - snoc-mm fix - Discussed with Krzysztof implemented if:then:else:not - dtc -I dtb -fs apq8039-t2.dtb prodcues /soc@0/i2c@78b5000: duplicate unit-address as does every other component that uses this polymorphic dts node - Renamed type-c i2c port manager IC to "typec" - Krzysztof /smsm/hexagon@1: Missing #address-cells in interrupt provider Same output as other upstream and recently upstreamed SoCs I left these alone for now link: https://lore.kernel.org/lkml/20230103010904.3201835-1-bryan.odonoghue@linaro.org/T/ bootable: https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=linux-next-23-01-16-msm8939-nocpr V2: - Sorts core dtsi node list by address followed by alpahbetical sorting within address sorted nodes - Bjorn - Drops use of 8916-pins - Bjorn - Adds msm8939-pm8916.dtsi - Stephan - Fixes every dts splat from previous submission minus non-converted .txt compat strings [1] and one yaml error in Bjorn's tree not in -next yet - I haven't applied Dmitry's change for tsens since that's not been picked up yet - Picks up a number of suggestions and fixes from Stephan Gerhold and Vincent Knecht - Depends on Applied: [PATCH v4 0/7] remoteproc: qcom_q6v5_mss: Add MSM8909 and MSM8953 https://lore.kernel.org/linux-arm-msm/167216232800.738877.17567287056128563074.b4-ty@kernel.org/ [PATCH v6 0/5] remoteproc: qcom: Add support for pronto-v3 https://lore.kernel.org/linux-arm-msm/167216232801.738877.15895916910585144737.b4-ty@kernel.org/ [PATCH v6 00/18] mdss-dsi-ctrl binding and dts fixes https://lore.kernel.org/linux-arm-msm/167233461766.1099840.17628700245792986354.b4-ty@kernel.org/ Awaiting application: https://lore.kernel.org/linux-arm-msm/20221228133058.213886-1-bryan.odonoghue@linaro.org/ - Previous https://lore.kernel.org/linux-arm-msm/20220419010903.3109514-1-bryan.odonoghue@linaro.org/ - Bootable tree https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=linux-next-23-01-03-msm8939-no-cpr - [1] DTC_CHK arch/arm64/boot/dts/qcom/apq8039-t2.dtb Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt qcom/apq8039-t2.dtb: idle-states: cpu-sleep-0:compatible:0: 'qcom,idle-state-spc' is not one of ['arm,idle-state', 'riscv,idle-state'] From schema: Documentation/devicetree/bindings/cpu/idle-states.yaml qcom/apq8039-t2.dtb: idle-states: cpu-sleep-0:compatible: ['qcom,idle-state-spc', 'arm,idle-state'] is too long From schema: Documentation/devicetree/bindings/cpu/idle-states.yaml arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /cpus/idle-states/cpu-sleep-0: failed to match any schema with compatible: ['qcom,idle-state-spc', 'arm,idle-state'] Documentation/devicetree/bindings/iommu/qcom,iommu.txt arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000: failed to match any schema with compatible: ['qcom,msm8916-iommu', 'qcom,msm-iommu-v1'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000/iommu-ctx@4000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000/iommu-ctx@5000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-sec'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000: failed to match any schema with compatible: ['qcom,msm8916-iommu', 'qcom,msm-iommu-v1'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000/iommu-ctx@1000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000/iommu-ctx@2000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns'] arch/arm64/boot/dts/qcom/pm8916.dtsi f5d7bca55425c8 qcom/apq8039-t2.dtb: pmic@0: 'extcon@1300' does not match any of the regexes: '(.*)?(wled|leds)@[0-9a-f]+$', '^adc-tm@[0-9a-f]+$', '^adc@[0-9a-f]+$', '^audio-codec@[0-9a-f]+$', '^charger@[0-9a-f]+$', '^mpps@[0-9a-f]+$', '^rtc@[0-9a-f]+$', '^temp-alarm@[0-9a-f]+$', '^usb-detect@[0-9a-f]+$', '^usb-vbus-regulator@[0-9a-f]+$', '^vibrator@[0-9a-f]+$', 'gpio@[0-9a-f]+$', 'pinctrl-[0-9]+', 'pon@[0-9a-f]+$' From schema: Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/spmi@200f000/pmic@1/audio-codec@f000: failed to match any schema with compatible: ['qcom,pm8916-wcd-analog-codec'] yaml documentation error not yet in -next arm64/boot/dts/qcom/apq8039-t2.dtb: remoteproc@4080000: qcom,halt-regs:0: [33] is too short From schema: Documentation/devicetree/bindings/remoteproc/qcom,msm8916-mss-pil.yaml Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/usb@78d9000: failed to match any schema with compatible: ['qcom,ci-hdrc'] Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt: compatible = "qcom,kpss-acc-v2"; arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b088000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b098000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b0a8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b0b8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b188000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b198000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b1a8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b1b8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2'] V1: This series adds in MSM8939 SoC support with two supported devices. - CPU MSM8939 is a non-PSCI compliant device. As such in the downstreaming shipped image custom code is used to bring non-boot cores out of reset. This drop specifies the boot-method as spin-table instead and is completely standard. To accomplish this, we rely on lk2nd. https://github.com/msm8916-mainline/lk2nd/pull/142 - Serial - i2c - USB - eMMC - MDP/DSI - WiFi - Bluetooth What's not included - CPR We have CPR working in a 4.19 kernel quite well but for now it feels like putting the cart before the horse to gate the SoC and boards on CPR. - Venus I've been told this works but I haven't tried it myself and right now consider it maybe working but probably not 100%. - Sound We have a copy-exactly from the 4.19 kernel here in the DTS. I haven't run the sound through any sort of reasonable test. Vincent Knecht has some PostmarketOS kernels which use a 5.17 version of this DTS to get sound up so, I think sound is in good shape. - CAMSS There are slight differences between msm8916 and msm8939 for CAMSS. It doesn't feel like tons of work but, right now it is work we haven't even started. - Devices I've booted on the Square device obviously and this is my regular hardware for upstream development. I've also booted on the Sony Xperia M4 Aqua including mutli-core bring-up, WiFi and ADB. Dependencies for this drop: qcom-cpufreq-nvmem: Add msm8939 with some fixups link: https://lore.kernel.org/linux-arm-msm/20220418162226.2983117-1-bryan.odonoghue@linaro.org/T/#t Fix apq8016 compat string link: https://lore.kernel.org/linux-arm-msm/20220418230956.3059563-1-bryan.odonoghue@linaro.org/T/#t dt-bindings: soc: qcom: smd-rpm: Fix missing MSM8936 compatible link: https://lore.kernel.org/linux-arm-msm/20220418231857.3061053-1-bryan.odonoghue@linaro.org/T/#u Bootable tree here: https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=v5.18-rc2%2bapq8039-without-cpr Bryan O'Donoghue (7): dt-bindings: arm: qcom: Document MSM8939 SoC binding dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* arm64: dts: qcom: Add msm8939 SoC arm64: dts: qcom: Add Square apq8039-t2 board arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Stephan Gerhold (1): arm64: dts: qcom: Add msm8939-pm8916.dtsi include .../devicetree/bindings/arm/qcom.yaml | 8 + .../bindings/interconnect/qcom,rpm.yaml | 73 +- .../bindings/soc/qcom/qcom,smd-rpm.yaml | 1 + arch/arm64/boot/dts/qcom/Makefile | 2 + arch/arm64/boot/dts/qcom/apq8039-t2.dts | 555 ++++ arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi | 82 + .../qcom/msm8939-sony-xperia-kanuti-tulip.dts | 466 ++++ arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++ drivers/clk/qcom/clk-smd-rpm.c | 2 + 9 files changed, 3551 insertions(+), 31 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi create mode 100644 arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi