| Message ID | 1701246516-11626-10-git-send-email-quic_cang@quicinc.com |
|---|---|
| State | New |
| Headers | show |
| Series | Enable HS-G5 support on SM8550 | expand |
On Wed, Nov 29, 2023 at 12:28:34AM -0800, Can Guo wrote: > In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext() > and stop proceeding if phy_set_mode_ext() fails. > > Signed-off-by: Can Guo <quic_cang@quicinc.com> > --- > drivers/ufs/host/ufs-qcom.c | 7 ++++++- > 1 file changed, 6 insertions(+), 1 deletion(-) > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c > index 30f4ca6..9c0ebbc 100644 > --- a/drivers/ufs/host/ufs-qcom.c > +++ b/drivers/ufs/host/ufs-qcom.c > @@ -475,7 +475,12 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba) > return ret; > } > > - phy_set_mode_ext(phy, mode, host->phy_gear); > + ret = phy_set_mode_ext(phy, mode, host->phy_gear); > + if (ret) { > + dev_err(hba->dev, "%s: phy set mode failed, ret = %d\n", > + __func__, ret); No need to print the error message here as it is already done in the PHY driver. Also, this patch should come before the PHY patch returning error. - Mani > + goto out_disable_phy; > + } > > /* power on phy - start serdes and phy's power and clocks */ > ret = phy_power_on(phy); > -- > 2.7.4 > >
On 11/30/2023 3:16 PM, Manivannan Sadhasivam wrote: > On Wed, Nov 29, 2023 at 12:28:34AM -0800, Can Guo wrote: >> In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext() >> and stop proceeding if phy_set_mode_ext() fails. >> >> Signed-off-by: Can Guo <quic_cang@quicinc.com> >> --- >> drivers/ufs/host/ufs-qcom.c | 7 ++++++- >> 1 file changed, 6 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c >> index 30f4ca6..9c0ebbc 100644 >> --- a/drivers/ufs/host/ufs-qcom.c >> +++ b/drivers/ufs/host/ufs-qcom.c >> @@ -475,7 +475,12 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba) >> return ret; >> } >> >> - phy_set_mode_ext(phy, mode, host->phy_gear); >> + ret = phy_set_mode_ext(phy, mode, host->phy_gear); >> + if (ret) { >> + dev_err(hba->dev, "%s: phy set mode failed, ret = %d\n", >> + __func__, ret); > > No need to print the error message here as it is already done in the PHY driver. > > Also, this patch should come before the PHY patch returning error. Sure. Thanks, Can Guo. > > - Mani > >> + goto out_disable_phy; >> + } >> >> /* power on phy - start serdes and phy's power and clocks */ >> ret = phy_power_on(phy); >> -- >> 2.7.4 >> >> >
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c index 30f4ca6..9c0ebbc 100644 --- a/drivers/ufs/host/ufs-qcom.c +++ b/drivers/ufs/host/ufs-qcom.c @@ -475,7 +475,12 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba) return ret; } - phy_set_mode_ext(phy, mode, host->phy_gear); + ret = phy_set_mode_ext(phy, mode, host->phy_gear); + if (ret) { + dev_err(hba->dev, "%s: phy set mode failed, ret = %d\n", + __func__, ret); + goto out_disable_phy; + } /* power on phy - start serdes and phy's power and clocks */ ret = phy_power_on(phy);
In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext() and stop proceeding if phy_set_mode_ext() fails. Signed-off-by: Can Guo <quic_cang@quicinc.com> --- drivers/ufs/host/ufs-qcom.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)