new file mode 100644
@@ -0,0 +1,160 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8953-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. MSM8953 TLMM block
+
+maintainers:
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+ This binding describes the Top Level Mode Multiplexer block found in the
+ MSM8953 platform.
+
+properties:
+ compatible:
+ const: qcom,msm8953-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description: Specifies the TLMM summary IRQ
+ maxItems: 1
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ description:
+ Specifies the PIN numbers and Flags, as defined in defined in
+ include/dt-bindings/interrupt-controller/irq.h
+ const: 2
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description: Specifying the pin number and flags, as defined in
+ include/dt-bindings/gpio/gpio.h
+ const: 2
+
+ gpio-ranges:
+ maxItems: 1
+
+ wakeup-parent:
+ maxItems: 1
+
+#PIN CONFIGURATION NODES
+patternProperties:
+ '^.*$':
+ if:
+ type: object
+ then:
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$"
+ - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
+ sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0,
+ qdsd_data1, qdsd_data2, qdsd_data3 ]
+ minItems: 1
+ maxItems: 16
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+
+ enum: [ accel_int, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1,
+ atest_char, atest_char0, atest_char1, atest_char2, atest_char3,
+ atest_gpsadc_dtest0_native, atest_gpsadc_dtest1_native, atest_tsens,
+ atest_wlan0, atest_wlan1, bimc_dte0, bimc_dte1, blsp1_spi,
+ blsp3_spi, blsp6_spi, blsp7_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3,
+ blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_spi1,
+ blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
+ blsp_spi8, blsp_uart2, blsp_uart4, blsp_uart5, blsp_uart6, cam0_ldo,
+ cam1_ldo, cam1_rst, cam1_standby, cam2_rst, cam2_standby, cam3_rst,
+ cam3_standby, cam_irq, cam_mclk, cap_int, cci_async, cci_i2c,
+ cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+ cdc_pdm0, codec_int1, codec_int2, codec_reset, cri_trng, cri_trng0,
+ cri_trng1, dac_calib0, dac_calib1, dac_calib10, dac_calib11,
+ dac_calib12, dac_calib13, dac_calib14, dac_calib15, dac_calib16,
+ dac_calib17, dac_calib18, dac_calib19, dac_calib2, dac_calib20,
+ dac_calib21, dac_calib22, dac_calib23, dac_calib24, dac_calib25,
+ dac_calib3, dac_calib4, dac_calib5, dac_calib6, dac_calib7,
+ dac_calib8, dac_calib9, dbg_out, ddr_bist, dmic0_clk, dmic0_data,
+ ebi_cdc, ebi_ch0, ext_lpass, flash_strobe, fp_int, gcc_gp1_clk_a,
+ gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a,
+ gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gpio, gsm0_tx, gsm1_tx,
+ gyro_int, hall_int, hdmi_int, key_focus, key_home, key_snapshot,
+ key_volp, ldo_en, ldo_update, lpass_slimbus, lpass_slimbus0,
+ lpass_slimbus1, m_voc, mag_int, mdp_vsync, mipi_dsi0, modem_tsync,
+ mss_lte, nav_pps, nav_pps_in_a, nav_pps_in_b, nav_tsync,
+ nfc_disable, nfc_dwl, nfc_irq, ois_sync, pa_indicator, pbs0, pbs1,
+ pbs2, pressure_int, pri_mi2s, pri_mi2s_mclk_a, pri_mi2s_mclk_b,
+ pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
+ pwr_down, pwr_modem_enabled_a, pwr_modem_enabled_b,
+ pwr_nav_enabled_a, pwr_nav_enabled_b, qdss_cti_trig_in_a0,
+ qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
+ qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
+ qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b,
+ qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
+ qdss_tracedata_b, sd_write, sdcard_det, sec_mi2s, sec_mi2s_mclk_a,
+ sec_mi2s_mclk_b, smb_int, ss_switch, ssbi_wtr1, ts_resout,
+ ts_sample, ts_xvdd, tsens_max, uim1_clk, uim1_data, uim1_present,
+ uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
+ uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan,
+ wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ]
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+ default: 2
+ description:
+ Selects the drive strength for the specified pins, in mA.
+
+ bias-pull-down: true
+
+ bias-pull-up: true
+
+ bias-disable: true
+
+ output-high: true
+
+ output-low: true
+
+ required:
+ - pins
+ - function
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8953-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 142>;
+ };
Add device tree bindings documentation for Qualcomm MSM8953 pinctrl driver. Signed-off-by: Vladimir Lypak <junak.pub@gmail.com> --- .../pinctrl/qcom,msm8953-pinctrl.yaml | 160 ++++++++++++++++++ 1 file changed, 160 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml