new file mode 100644
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
+
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+&spmi_bus {
+ pmic@0 {
+ compatible = "qcom,pmp8074", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmp8074_adc: adc@3100 {
+ compatible = "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ ref-gnd@0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vref-1p25@1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vref-vadc@2 {
+ reg = <ADC5_VREF_VADC>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pmic_die: die-temp@6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ xo_therm: xo-temp@76 {
+ reg = <ADC5_XO_THERM_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm1: thermistor1@77 {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm2: thermistor2@78 {
+ reg = <ADC5_AMUX_THM2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ pa_therm3: thermistor3@79 {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ };
+
+ vph-pwr@131 {
+ reg = <ADC5_VPH_PWR>;
+ qcom,pre-scaling = <1 3>;
+ };
+ };
+
+ pmp8074_rtc: rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ allow-set-time;
+ status = "disabled";
+ };
+
+ pmp8074_gpios: gpio@c000 {
+ compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmp8074_gpios 0 0 12>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmic@1 {
+ compatible = "qcom,pmp8074", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+
+ regulators {
+ compatible = "qcom,pmp8074-regulators";
+
+ s3: s3 {
+ regulator-name = "vdd_s3";
+ regulator-min-microvolt = <592000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s4: s4 {
+ regulator-name = "vdd_s4";
+ regulator-min-microvolt = <712000>;
+ regulator-max-microvolt = <992000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l11: l11 {
+ regulator-name = "l11";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
PMP8074 is a companion PMIC to the Qualcomm IPQ8074 series that is controlled via SPMI. Add DTSI for it providing GPIO, regulator, RTC and VADC support. RTC is disabled by default as there is no built-in battery so it will loose time unless board vendor added a battery, so make it optional. Signed-off-by: Robert Marko <robimarko@gmail.com> --- Changes in v7: * Dual license with BSD-3-Clause * Use "-" instead of underscores in node names Changes in v6: * Add RTC and GPIO nodes Changes in v5: * Remove #address-cells and #size-cells as they are not required for regulator subnodes --- arch/arm64/boot/dts/qcom/pmp8074.dtsi | 125 ++++++++++++++++++++++++++ 1 file changed, 125 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmp8074.dtsi