| Message ID | 20230104-topic-sm8550-upstream-dts-display-v3-3-46f0d4e57752@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: sm8550-mtp: enable DSI panel | expand |
On 18/01/2023 09:55, Neil Armstrong wrote: > Add nodes for the Visionox VTDR6130 found on the SM8550-MTP > device. > > TLMM states are also added for the Panel reset GPIO and > Tearing Effect signal for when the panel is running in > DSI Command mode. > > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 56 +++++++++++++++++++++++++++++++++ > 1 file changed, 56 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts > index 0dfd1d3db86c..2de387aa2c2d 100644 > --- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts > +++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts > @@ -370,6 +370,34 @@ &mdss { > &mdss_dsi0 { > vdda-supply = <&vreg_l3e_1p2>; > status = "okay"; > + > + panel@0 { > + compatible = "visionox,vtdr6130"; > + reg = <0>; > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>; > + pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>; > + > + vddio-supply = <&vreg_l12b_1p8>; > + vci-supply = <&vreg_l13b_3p0>; > + vdd-supply = <&vreg_l11b_1p2>; > + > + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; > + > + status = "okay"; No need unless you override existing device node. > + > + port { > + panel0_in: endpoint { > + remote-endpoint = <&mdss_dsi0_out>; > + }; > + }; > + }; > +}; Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts index 0dfd1d3db86c..2de387aa2c2d 100644 --- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts @@ -370,6 +370,34 @@ &mdss { &mdss_dsi0 { vdda-supply = <&vreg_l3e_1p2>; status = "okay"; + + panel@0 { + compatible = "visionox,vtdr6130"; + reg = <0>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>; + pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>; + + vddio-supply = <&vreg_l12b_1p8>; + vci-supply = <&vreg_l13b_3p0>; + vdd-supply = <&vreg_l11b_1p2>; + + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; + + status = "okay"; + + port { + panel0_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + remote-endpoint = <&panel0_in>; + data-lanes = <0 1 2 3>; }; &mdss_dsi0_phy { @@ -415,6 +443,34 @@ &sleep_clk { &tlmm { gpio-reserved-ranges = <32 8>; + + sde_dsi_active: sde-dsi-active-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + sde_dsi_suspend: sde-dsi-suspend-state { + pins = "gpio133"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + sde_te_active: sde-te-active-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; + + sde_te_suspend: sde-te-suspend-state { + pins = "gpio86"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; }; &uart7 {
Add nodes for the Visionox VTDR6130 found on the SM8550-MTP device. TLMM states are also added for the Panel reset GPIO and Tearing Effect signal for when the panel is running in DSI Command mode. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 56 +++++++++++++++++++++++++++++++++ 1 file changed, 56 insertions(+)