diff mbox series

[v3,12/14] arm64: dts: qcom: Add initial support for MSM8917

Message ID 20241107-msm8917-v3-12-6ddc5acd978b@mainlining.org
State Superseded
Headers show
Series Add MSM8917/PM8937/Redmi 5A | expand

Commit Message

Barnabás Czémán Nov. 7, 2024, 5:02 p.m. UTC
From: Otto Pflüger <otto.pflueger@abscue.de>

Add initial support for MSM8917 SoC.

Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
[reword commit, rebase, fix schema errors]
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
---
 arch/arm64/boot/dts/qcom/msm8917.dtsi | 2007 +++++++++++++++++++++++++++++++++
 1 file changed, 2007 insertions(+)

Comments

Konrad Dybcio Nov. 8, 2024, 5:03 p.m. UTC | #1
On 7.11.2024 6:02 PM, Barnabás Czémán wrote:
> From: Otto Pflüger <otto.pflueger@abscue.de>
> 
> Add initial support for MSM8917 SoC.
> 
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> [reword commit, rebase, fix schema errors]
> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
> ---

[...]

> +		domain-idle-states {
> +			cluster_pwrdn: cluster-gdhs {

Please rename these to cluster-sleep-<n> and sort from shallowest to
deepest sleep state, in this case: ret, pwrdn, pc

[...]

> +
> +		l2_0: l2-cache {
> +			compatible = "cache";
> +			cache-level = <2>;
> +			cache-unified;
> +		};

Please put this under the cpu0 node

[...]

> +		restart@4ab000 {
> +			compatible = "qcom,pshold";
> +			reg = <0x4ab000 0x4>;

Please also pad all address parts to 8 hex digits with leading zeroes

[...]

> +			gpu_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-598000000 {
> +					opp-hz = /bits/ 64 <598000000>;
> +				};
> +
> +				opp-523200000 {
> +					opp-hz = /bits/ 64 <523200000>;
> +				};
> +
> +				opp-484800000 {
> +					opp-hz = /bits/ 64 <484800000>;
> +				};
> +
> +				opp-400000000 {
> +					opp-hz = /bits/ 64 <400000000>;
> +				};
> +
> +				opp-270000000 {
> +					opp-hz = /bits/ 64 <270000000>;
> +				};
> +
> +				opp-19200000 {
> +					opp-hz = /bits/ 64 <19200000>;
> +				};

Does the GPU actually function at 19.2 MHz? You can check this by removing
all other entries and starting some gpu workload

[...]

> +		cpuss1-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;

You can remove polling-delay (not -passive), as we have an interrupt
that fires on threshold crossing

> +
> +			thermal-sensors = <&tsens 4>;
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&cpuss1_alert0>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +
> +			trips {
> +				cpuss1_crit: cpuss1-crit {
> +					temperature = <100000>;
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +
> +				cpuss1_alert0: trip-point0 {
> +					temperature = <75000>;
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +
> +				cpuss1_alert1: trip-point1 {
> +					temperature = <85000>;
> +					hysteresis = <2000>;
> +					type = "hot";
> +				};

Sorting these by temperature, rising would be nice

Konrad
Barnabás Czémán Nov. 9, 2024, 11:36 a.m. UTC | #2
On 2024-11-08 18:03, Konrad Dybcio wrote:
> On 7.11.2024 6:02 PM, Barnabás Czémán wrote:
>> From: Otto Pflüger <otto.pflueger@abscue.de>
>> 
>> Add initial support for MSM8917 SoC.
>> 
>> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
>> [reword commit, rebase, fix schema errors]
>> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>> ---
> 
> [...]
> 
>> +		domain-idle-states {
>> +			cluster_pwrdn: cluster-gdhs {
> 
> Please rename these to cluster-sleep-<n> and sort from shallowest to
> deepest sleep state, in this case: ret, pwrdn, pc
> 
> [...]
> 
>> +
>> +		l2_0: l2-cache {
>> +			compatible = "cache";
>> +			cache-level = <2>;
>> +			cache-unified;
>> +		};
> 
> Please put this under the cpu0 node
> 
> [...]
> 
>> +		restart@4ab000 {
>> +			compatible = "qcom,pshold";
>> +			reg = <0x4ab000 0x4>;
> 
> Please also pad all address parts to 8 hex digits with leading zeroes
> 
> [...]
> 
>> +			gpu_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-598000000 {
>> +					opp-hz = /bits/ 64 <598000000>;
>> +				};
>> +
>> +				opp-523200000 {
>> +					opp-hz = /bits/ 64 <523200000>;
>> +				};
>> +
>> +				opp-484800000 {
>> +					opp-hz = /bits/ 64 <484800000>;
>> +				};
>> +
>> +				opp-400000000 {
>> +					opp-hz = /bits/ 64 <400000000>;
>> +				};
>> +
>> +				opp-270000000 {
>> +					opp-hz = /bits/ 64 <270000000>;
>> +				};
>> +
>> +				opp-19200000 {
>> +					opp-hz = /bits/ 64 <19200000>;
>> +				};
> 
> Does the GPU actually function at 19.2 MHz? You can check this by 
> removing
> all other entries and starting some gpu workload
Yes
> 
> [...]
> 
>> +		cpuss1-thermal {
>> +			polling-delay-passive = <250>;
>> +			polling-delay = <1000>;
> 
> You can remove polling-delay (not -passive), as we have an interrupt
> that fires on threshold crossing
> 
>> +
>> +			thermal-sensors = <&tsens 4>;
>> +
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpuss1_alert0>;
>> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +
>> +			trips {
>> +				cpuss1_crit: cpuss1-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <2000>;
>> +					type = "critical";
>> +				};
>> +
>> +				cpuss1_alert0: trip-point0 {
>> +					temperature = <75000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpuss1_alert1: trip-point1 {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "hot";
>> +				};
> 
> Sorting these by temperature, rising would be nice
> 
> Konrad
Konrad Dybcio Nov. 9, 2024, 11:53 a.m. UTC | #3
On 9.11.2024 12:36 PM, barnabas.czeman@mainlining.org wrote:
> On 2024-11-08 18:03, Konrad Dybcio wrote:
>> On 7.11.2024 6:02 PM, Barnabás Czémán wrote:
>>> From: Otto Pflüger <otto.pflueger@abscue.de>
>>>
>>> Add initial support for MSM8917 SoC.
>>>
>>> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
>>> [reword commit, rebase, fix schema errors]
>>> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
>>> ---

[...]

>>> +                opp-19200000 {
>>> +                    opp-hz = /bits/ 64 <19200000>;
>>> +                };
>>
>> Does the GPU actually function at 19.2 MHz? You can check this by removing
>> all other entries and starting some gpu workload
> Yes

Thanks for confirming, feel free to keep this entry then

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..f7446dd7d44c9f2db6d309a817c0e58cbd143b5c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
@@ -0,0 +1,2007 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <dt-bindings/clock/qcom,gcc-msm8917.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,apr.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	chosen { };
+
+	clocks {
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			next-level-cache = <&l2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&cpu_pd0>;
+			power-domain-names = "psci";
+		};
+
+		cpu1: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			next-level-cache = <&l2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&cpu_pd1>;
+			power-domain-names = "psci";
+		};
+
+		cpu2: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x102>;
+			next-level-cache = <&l2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&cpu_pd2>;
+			power-domain-names = "psci";
+		};
+
+		cpu3: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x103>;
+			next-level-cache = <&l2_0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>;
+			power-domains = <&cpu_pd3>;
+			power-domain-names = "psci";
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		domain-idle-states {
+			cluster_pwrdn: cluster-gdhs {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000043>;
+				entry-latency-us = <240>;
+				exit-latency-us = <280>;
+				min-residency-us = <806>;
+			};
+
+			cluster_pc: cluster-power-collapse {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000053>;
+				entry-latency-us = <700>;
+				exit-latency-us = <1000>;
+				min-residency-us = <6500>;
+			};
+
+			cluster_ret: cluster-retention {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000023>;
+				entry-latency-us = <700>;
+				exit-latency-us = <650>;
+				min-residency-us = <1972>;
+			};
+
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			cpu_sleep_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "standalone-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <125>;
+				exit-latency-us = <180>;
+				min-residency-us = <595>;
+				local-timer-stop;
+			};
+		};
+
+		l2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+
+		cpu_opp_table: opp-table-cpu {
+			compatible = "operating-points-v2";
+			opp-shared;
+
+			opp-960000000 {
+				opp-hz = /bits/ 64 <960000000>;
+			};
+
+			opp-1094400000 {
+				opp-hz = /bits/ 64 <1094400000>;
+			};
+
+			opp-1248000000 {
+				opp-hz = /bits/ 64 <1248000000>;
+			};
+
+			opp-1401600000 {
+				opp-hz = /bits/ 64 <1401600000>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-msm8916", "qcom,scm";
+			clocks = <&gcc GCC_CRYPTO_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
+
+			qcom,dload-mode = <&tcsr 0x6100>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0x80000000 0 0>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		cluster_pd: power-domain-cluster {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&cluster_pwrdn>, <&cluster_ret>, <&cluster_pc>;
+		};
+
+		cpu_pd0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>;
+		};
+
+		cpu_pd1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>;
+		};
+
+		cpu_pd2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>;
+		};
+
+		cpu_pd3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>;
+		};
+	};
+
+	rpm: remoteproc {
+		compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc";
+
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8917", "qcom,smd-rpm";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8917-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION>;
+						};
+
+						rpmpd_opp_ret_plus: opp2 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
+						};
+
+						rpmpd_opp_min_svs: opp3 {
+							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+						};
+
+						rpmpd_opp_low_svs: opp4 {
+							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+						};
+
+						rpmpd_opp_svs: opp5 {
+							opp-level = <RPM_SMD_LEVEL_SVS>;
+						};
+
+						rpmpd_opp_svs_plus: opp6 {
+							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+						};
+
+						rpmpd_opp_nom: opp7 {
+							opp-level = <RPM_SMD_LEVEL_NOM>;
+						};
+
+						rpmpd_opp_nom_plus: opp8 {
+							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+						};
+
+						rpmpd_opp_turbo: opp9 {
+							opp-level = <RPM_SMD_LEVEL_TURBO>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		qseecom_mem: qseecom@85b00000 {
+			reg = <0x0 0x85b00000 0x0 0x800000>;
+			no-map;
+		};
+
+		smem@86300000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x86300000 0x0 0x100000>;
+			no-map;
+
+			hwlocks = <&tcsr_mutex 3>;
+			qcom,rpm-msg-ram = <&rpm_msg_ram>;
+		};
+
+		reserved@86400000 {
+			reg = <0x0 0x86400000 0x0 0x400000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@86800000 {
+			/*
+			 * The memory region for the mpss firmware is generally
+			 * relocatable and could be allocated dynamically.
+			 * However, many firmware versions tend to fail when
+			 * loaded to some special addresses, so it is hard to
+			 * define reliable alloc-ranges.
+			 *
+			 * alignment = <0x0 0x400000>;
+			 * alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			 */
+			reg = <0x0 0x86800000 0x0 0>; /* size is device-specific */
+			no-map;
+			status = "disabled";
+		};
+
+		rmtfs@92100000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0x92100000 0x0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+
+		adsp_mem: adsp {
+			size = <0x0 0x1100000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		mba_mem: mba {
+			size = <0x0 0x100000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		venus_mem: venus {
+			size = <0x0 0x400000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+
+		wcnss_mem: wcnss {
+			size = <0x0 0x700000>;
+			alignment = <0x0 0x100000>;
+			alloc-ranges = <0x0 0x86800000 0x0 0x8000000>;
+			no-map;
+			status = "disabled";
+		};
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-wcnss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mboxes = <0>, <&apcs 13>, <0>, <&apcs 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smsm: hexagon@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@6 {
+			reg = <6>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+		compatible = "simple-bus";
+
+		rpm_msg_ram: sram@60000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0x60000 0x8000>;
+		};
+
+		usb_hs_phy: phy@6c000 {
+			compatible = "qcom,usb-hs-28nm-femtophy";
+			reg = <0x6c000 0x200>;
+			#phy-cells = <0>;
+			clocks = <&xo_board>,
+				 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+			clock-names = "ref", "ahb", "sleep";
+			resets = <&gcc GCC_QUSB2_PHY_BCR>,
+				 <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
+			reset-names = "phy", "por";
+			status = "disabled";
+		};
+
+		qfprom: qfprom@a4000 {
+			compatible = "qcom,msm8917-qfprom", "qcom,qfprom";
+			reg = <0xa4000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@1d8 {
+				reg = <0x1d8 1>;
+				bits = <0 8>;
+			};
+
+			tsens_s5_p1: s5-p1@1d9 {
+				reg = <0x1d9 1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p2: s5-p2@1d9 {
+				reg = <0x1d9 2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@1da {
+				reg = <0x1da 2>;
+				bits = <4 6>;
+			};
+
+			tsens_s6_p2: s6-p2@1db {
+				reg = <0x1db 1>;
+				bits = <2 6>;
+			};
+
+			tsens_s7_p1: s7-p1@1dc {
+				reg = <0x1dc 1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@1dc {
+				reg = <0x1dc 2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p1: s8-p1@1dd {
+				reg = <0x1dd 2>;
+				bits = <4 6>;
+			};
+
+			tsens_s8_p2: s8-p2@1de {
+				reg = <0x1de 1>;
+				bits = <2 6>;
+			};
+
+			tsens_base2: base2@1df {
+				reg = <0x1df 1>;
+				bits = <0 8>;
+			};
+
+			tsens_mode: mode@210 {
+				reg = <0x210 1>;
+				bits = <0 3>;
+			};
+
+			tsens_s0_p1: s0-p1@210 {
+				reg = <0x210 2>;
+				bits = <3 6>;
+			};
+
+			tsens_s0_p2: s0-p2@211 {
+				reg = <0x211 1>;
+				bits = <1 6>;
+			};
+
+			tsens_s1_p1: s1-p1@211 {
+				reg = <0x211 2>;
+				bits = <7 6>;
+			};
+
+			tsens_s1_p2: s1-p2@212 {
+				reg = <0x212 2>;
+				bits = <5 6>;
+			};
+
+			tsens_s2_p1: s2-p1@213 {
+				reg = <0x213 2>;
+				bits = <3 6>;
+			};
+
+			tsens_s2_p2: s2-p2@214 {
+				reg = <0x214 1>;
+				bits = <1 6>;
+			};
+
+			tsens_s3_p1: s3-p1@214 {
+				reg = <0x214 2>;
+				bits = <7 6>;
+			};
+
+			tsens_s3_p2: s3-p2@215 {
+				reg = <0x215 2>;
+				bits = <5 6>;
+			};
+
+			tsens_s4_p1: s4-p1@216 {
+				reg = <0x216 2>;
+				bits = <3 6>;
+			};
+
+			tsens_s4_p2: s4-p2@217 {
+				reg = <0x217 1>;
+				bits = <1 6>;
+			};
+
+			tsens_s9_p1: s9-p1@230{
+				reg = <0x230 1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p2: s9-p2@230 {
+				reg = <0x230 2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1: s10-p1@231 {
+				reg = <0x231 2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10-p2@232 {
+				reg = <0x232 1>;
+				bits = <2 6>;
+			};
+		};
+
+		rng@e3000 {
+			compatible = "qcom,prng";
+			reg = <0xe3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		tsens: thermal-sensor@4a9000 {
+			compatible = "qcom,msm8937-tsens", "qcom,tsens-v1";
+			reg = <0x4a9000 0x1000>,
+			      <0x4a8000 0x1000>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2";
+			#qcom,sensors = <11>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x4ab000 0x4>;
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,msm8917-pinctrl";
+			reg = <0x1000000 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 134>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			blsp1_uart1_default: blsp1-uart1-default-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "blsp_uart1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default-state {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_uart2_sleep: blsp1-uart2-sleep-state {
+				pins = "gpio4", "gpio5";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			i2c2_default: i2c2-default-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c2_sleep: i2c2-sleep-state {
+				pins = "gpio6", "gpio7";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c3_default: i2c3-default-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c3_sleep: i2c3-sleep-state {
+				pins = "gpio10", "gpio11";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c4_default: i2c4-default-state {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c4_sleep: i2c4-sleep-state {
+				pins = "gpio14", "gpio15";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c5_default: i2c5-default-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c5_sleep: i2c5-sleep-state {
+				pins = "gpio18", "gpio19";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdc1_clk_on: sdc1-clk-on-state {
+				pins = "sdc1_clk";
+				bias-disable;
+				drive-strength = <16>;
+			};
+
+			sdc1_clk_off: sdc1-clk-off-state {
+				pins = "sdc1_clk";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc1_cmd_on: sdc1-cmd-on-state {
+				pins = "sdc1_cmd";
+				bias-disable;
+				drive-strength = <10>;
+			};
+
+			sdc1_cmd_off: sdc1-cmd-off-state {
+				pins = "sdc1_cmd";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc1_data_on: sdc1-data-on-state {
+				pins = "sdc1_data";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc1_data_off: sdc1-data-off-state {
+				pins = "sdc1_data";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			sdc1_rclk_on: sdc1-rclk-on-state {
+				pins = "sdc1_rclk";
+				bias-pull-down;
+			};
+
+			sdc1_rclk_off: sdc1-rclk-off-state {
+				pins = "sdc1_rclk";
+				bias-pull-down;
+			};
+
+			sdc2_clk_on: sdc2-clk-on-state {
+				pins = "sdc2_clk";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			sdc2_clk_off: sdc2-clk-off-state {
+				pins = "sdc2_clk";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc2_cmd_on: sdc2-cmd-on-state {
+				pins = "sdc2_cmd";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc2_cmd_off: sdc2-cmd-off-state {
+				pins = "sdc2_cmd";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			sdc2_cd_on: cd-on-state {
+				pins = "gpio67";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			sdc2_cd_off: cd-off-state {
+				pins = "gpio67";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdc2_data_on: sdc2-data-on-state {
+				pins = "sdc2_data";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc2_data_off: sdc2-data-off-state {
+				pins = "sdc2_data";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			spi3_default: spi3-default-state {
+				cs-pins {
+					pins = "gpio10";
+					function = "blsp_spi3";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				spi-pins {
+					pins = "gpio8", "gpio9", "gpio11";
+					function = "blsp_spi3";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			spi3_sleep: spi3-sleep-state {
+				cs-pins {
+					pins = "gpio10";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				spi-pins {
+					pins = "gpio8", "gpio9", "gpio11";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+			};
+
+			spi6_default: spi6-default-state {
+				cs0-pins {
+					pins = "gpio47";
+					function = "blsp_spi6";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cs1-pins {
+					pins = "gpio22";
+					function = "blsp_spi6";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				spi-pins {
+					pins = "gpio20", "gpio21", "gpio23";
+					function = "blsp_spi6";
+					drive-strength = <16>;
+					bias-disable;
+				};
+			};
+
+			spi6_sleep: spi6-sleep-state {
+				cs0-pins {
+					pins = "gpio47";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cs1-pins {
+					pins = "gpio22";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				spi-pins {
+					pins = "gpio20", "gpio21", "gpio23";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+			};
+
+			wcnss_pin_a: wcnss-active-state {
+				wcss-wlan-pins {
+					pins = "gpio79", "gpio80";
+					function = "wcss_wlan";
+					drive-strength = <6>;
+					bias-pull-up;
+
+				};
+
+				wcss-wlan0-pins {
+					pins = "gpio78";
+					function = "wcss_wlan0";
+					drive-strength = <6>;
+					bias-pull-up;
+
+				};
+
+				wcss-wlan1-pins {
+					pins = "gpio77";
+					function = "wcss_wlan1";
+					drive-strength = <6>;
+					bias-pull-up;
+
+				};
+
+				wcss-wlan2-pins {
+					pins = "gpio76";
+					function = "wcss_wlan2";
+					drive-strength = <6>;
+					bias-pull-up;
+
+				};
+			};
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,gcc-msm8917";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0x1800000 0x80000>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>;
+			clock-names = "xo",
+				      "sleep_clk",
+				      "dsi0pll",
+				      "dsi0pllbyte";
+		};
+
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x1905000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8917", "syscon";
+			reg = <0x1937000 0x30000>;
+		};
+
+		mdss: display-subsystem@1a00000 {
+			compatible = "qcom,mdss";
+			reg = <0x1a00000 0x1000>,
+			      <0x1ab0000 0x1040>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdp: display-controller@1a01000 {
+				compatible = "qcom,msm8917-mdp5", "qcom,mdp5";
+				reg = <0x1a01000 0x89000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				power-domains = <&gcc MDSS_GDSC>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				iommus = <&apps_iommu 0x15>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@1a94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0x1a94000 0x300>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+						  <&gcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE0_CLK>,
+					 <&gcc GCC_MDSS_PCLK0_CLK>,
+					 <&gcc GCC_MDSS_ESC0_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core";
+				phys = <&mdss_dsi0_phy>;
+
+				operating-points-v2 = <&mdss_dsi0_opp_table>;
+				power-domains = <&rpmpd MSM8917_VDDCX>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dsi0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-125000000 {
+						opp-hz = /bits/ 64 <125000000>;
+						required-opps = <&rpmpd_opp_svs>;
+					};
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@1a94a00 {
+				compatible = "qcom,dsi-phy-28nm-8937";
+				reg = <0x1a94a00 0xd4>,
+				      <0x1a94400 0x280>,
+				      <0x1a94b80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&xo_board>;
+				clock-names = "iface", "ref";
+			};
+		};
+
+		apps_iommu: iommu@1e20000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
+			ranges = <0 0x1e20000 0x20000>;
+
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_APSS_TCU_CLK>;
+			clock-names = "iface", "bus";
+
+			qcom,iommu-secure-id = <17>;
+
+			/* VFE */
+			iommu-ctx@14000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x14000 0x1000>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* MDP_0 */
+			iommu-ctx@15000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x15000 0x1000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			/* VENUS_NS */
+			iommu-ctx@16000 {
+				compatible = "qcom,msm-iommu-v1-ns";
+				reg = <0x16000 0x1000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		gpu_iommu: iommu@1f08000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#iommu-cells = <1>;
+
+			compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1";
+
+			ranges = <0 0x1f08000 0x10000>;
+			clocks = <&gcc GCC_SMMU_CFG_CLK>,
+				 <&gcc GCC_GFX_TCU_CLK>;
+			clock-names = "iface", "bus";
+			qcom,iommu-secure-id = <18>;
+
+			iommu-ctx@0 {
+				compatible = "qcom,msm-iommu-v2-ns";
+				reg = <0 0x1000>;
+				interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		gpu: gpu@1c00000 {
+			compatible = "qcom,adreno-306.32", "qcom,adreno";
+			reg = <0x1c00000 0x20000>;
+			reg-names = "kgsl_3d0_reg_memory";
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+			clock-names = "core",
+				      "iface",
+				      "mem_iface",
+				      "alt_mem_iface",
+				      "gfx3d";
+			clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
+				 <&gcc GCC_OXILI_AHB_CLK>,
+				 <&gcc GCC_BIMC_GFX_CLK>,
+				 <&gcc GCC_BIMC_GPU_CLK>,
+				 <&gcc GFX3D_CLK_SRC>;
+			power-domains = <&gcc OXILI_GX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+			#cooling-cells = <2>;
+
+			iommus = <&gpu_iommu 0>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-598000000 {
+					opp-hz = /bits/ 64 <598000000>;
+				};
+
+				opp-523200000 {
+					opp-hz = /bits/ 64 <523200000>;
+				};
+
+				opp-484800000 {
+					opp-hz = /bits/ 64 <484800000>;
+				};
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>;
+				};
+
+				opp-270000000 {
+					opp-hz = /bits/ 64 <270000000>;
+				};
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+				};
+			};
+		};
+
+		spmi_bus: spmi@200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x200f000 0x001000>,
+			      <0x2400000 0x800000>,
+			      <0x2c00000 0x800000>,
+			      <0x3800000 0x200000>,
+			      <0x200a000 0x002100>;
+			reg-names = "core",
+				    "chnls",
+				    "obsrvr",
+				    "intr",
+				    "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@4044000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x4044000 0x19000>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+
+			status = "disabled";
+		};
+
+		sdhc_1: mmc@7824900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7824900 0x500>,
+			      <0x7824000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			power-domains = <&rpmpd MSM8917_VDDCX>;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-ddr-1_8v;
+			bus-width = <8>;
+			non-removable;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@7864900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7864900 0x500>,
+			      <0x7864000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			power-domains = <&rpmpd MSM8917_VDDCX>;
+			bus-width = <4>;
+			status = "disabled";
+		};
+
+		blsp1_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x7884000 0x1f000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			qcom,controlled-remotely;
+			#dma-cells = <1>;
+			num-channels = <12>;
+			qcom,num-ees = <4>;
+			qcom,ee = <0>;
+		};
+
+		blsp2_dma: dma-controller@7ac4000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x7ac4000 0x1d000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			qcom,controlled-remotely;
+			#dma-cells = <1>;
+			num-channels = <10>;
+			qcom,num-ees = <4>;
+			qcom,ee = <0>;
+		};
+
+		blsp1_uart1: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x78af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&blsp1_uart1_default>;
+			pinctrl-1 = <&blsp1_uart1_sleep>;
+			pinctrl-names = "default", "sleep";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x78b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
+			pinctrl-names = "default", "sleep";
+			status = "disabled";
+		};
+
+		blsp_i2c2: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c2_default>;
+			pinctrl-1 = <&i2c2_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c3: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c3_default>;
+			pinctrl-1 = <&i2c3_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi3: spi@78b7000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x78b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi3_default>;
+			pinctrl-1 = <&spi3_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c4: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b8000 0x500>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp1_dma 10>, <&blsp1_dma 11>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c4_default>;
+			pinctrl-1 = <&i2c4_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_i2c5: i2c@7af5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x7af5000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&i2c5_default>;
+			pinctrl-1 = <&i2c5_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp_spi6: spi@7af6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x7af6000 0x600>;
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
+			dma-names = "tx", "rx";
+			pinctrl-0 = <&spi6_default>;
+			pinctrl-1 = <&spi6_sleep>;
+			pinctrl-names = "default", "sleep";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb: usb@78db000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x78db000 0x200>,
+			      <0x78db200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <80000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+		};
+
+		wcnss: remoteproc@a204000 {
+			compatible = "qcom,pronto-v3-pil", "qcom,pronto";
+			reg = <0xa204000 0x2000>,
+			      <0xa202000 0x1000>,
+			      <0xa21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_mem>;
+
+			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8917_VDDCX>,
+					<&rpmpd MSM8917_VDDMX>;
+			power-domain-names = "cx", "mx";
+
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			pinctrl-0 = <&wcnss_pin_a>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+
+			wcnss_iris: iris {
+				clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+				clock-names = "xo";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&apcs 17>;
+				qcom,smd-edge = <6>;
+				qcom,remote-pid = <4>;
+
+				label = "pronto";
+
+				wcnss_ctrl: wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+
+					qcom,mmio = <&wcnss>;
+
+					wcnss_bt: bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wcnss_wifi: wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+							     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0xb000000 0x1000>,
+			      <0xb002000 0x1000>;
+		};
+
+		apcs: mailbox@b011000 {
+			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+			reg = <0xb011000 0x1000>;
+			#mbox-cells = <1>;
+			clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "pll", "aux", "ref";
+			#clock-cells = <0>;
+		};
+
+		a53pll: clock@b016000 {
+			compatible = "qcom,msm8939-a53pll";
+			reg = <0xb016000 0x40>;
+			clocks = <&xo_board>;
+			clock-names = "xo";
+			#clock-cells = <0>;
+			operating-points-v2 = <&pll_opp_table>;
+
+			pll_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-960000000 {
+					opp-hz = /bits/ 64 <960000000>;
+				};
+
+				opp-1094400000 {
+					opp-hz = /bits/ 64 <1094400000>;
+				};
+
+				opp-1248000000 {
+					opp-hz = /bits/ 64 <1248000000>;
+				};
+
+				opp-1401600000 {
+				      opp-hz = /bits/ 64 <1401600000>;
+				};
+			};
+		};
+
+		watchdog@b017000 {
+			compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
+			reg = <0xb017000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@b120000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xb120000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@b121000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb121000 0x1000>,
+				      <0xb122000 0x1000>;
+			};
+
+			frame@b123000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb123000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb124000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb125000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb126000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb127000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb128000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+
+	thermal_zones: thermal-zones {
+		aoss-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				aoss_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		camera-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				camera_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		cpuss1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpuss1_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpuss1_crit: cpuss1-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpuss1_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpuss1_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu0_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu0_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu1_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu1_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu1_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu2_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu2_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu2_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu3_crit: cpu-crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu3_alert0: trip-point0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				cpu3_alert1: trip-point1 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+		};
+
+		gpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			cooling-maps {
+				map0 {
+					trip = <&gpu_alert>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				gpu_crit: gpu-crit {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				gpu_alert: trip-point0 {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+			};
+
+		};
+
+		mdm-core-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				mdm_core_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		q6-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				q6_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};