| Message ID | 20180801180232.23680-1-manivannan.sadhasivam@linaro.org |
|---|---|
| Headers | show |
| Series | Add Actions Semiconductor Owl S900 I2C support | expand |
On Wed, Aug 01, 2018 at 11:32:28PM +0530, Manivannan Sadhasivam wrote: > Add pinctrl definition for Actions Semiconductor S900 I2C controller. > Pinctrl definitions are only available for I2C0, I2C1, and I2C2. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Note that I don't take DTS patches, so skipping patches 2-4.
On Sat, Aug 04, 2018 at 11:04:40PM +0200, Wolfram Sang wrote: > On Wed, Aug 01, 2018 at 11:32:28PM +0530, Manivannan Sadhasivam wrote: > > Add pinctrl definition for Actions Semiconductor S900 I2C controller. > > Pinctrl definitions are only available for I2C0, I2C1, and I2C2. > > > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > > Note that I don't take DTS patches, so skipping patches 2-4. > Hi Andreas, Can you please take the DTS patches through Actions tree? Thanks, Mani -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
This patchset adds I2C controller support for Actions Semiconductor S900 SoC. This driver has been structured in a way such that there will be only one controller driver for the whole Owl family series (S500, S700 and S900 SoCs). There are 6 I2C controllers with separate memory mapped register space. The I2C controller can handle atmost two messages concatenated by a repeated start via its internal address feature. Hence the driver uses this feature for messages of length greater than 1. In those cases, the first message of the combined message should be a `write` with maximum message length 6 and the second message's maximum length should be 240 bytes. As far as the bus speed is concerned, this driver only supports Standard (100KHz) and High speed (400KHz) for now. The pinctrl definitions are only available for I2C0, I2C1 and I2C2. With the mux option available only for I2C0. For Bubblegum-96 board utilizing the S900 SoC, only I2C1 and I2C2 which are exposed on the Low speed expansion connector are enabled. This series depends on the pinctrl patch [1] is still not merged by the platform maintainer Andreas but it has been reviewed by the pinctrl maintainer Linus Walleij. For the reference, I have queued up all reviewed dts patches in my tree [2] from which Andreas is picking them for 4.19. For this series, since the dts patches will go through the ARM SoC tree, Andreas will pick it up once it is reviewed. Thanks, Mani [1] https://patchwork.kernel.org/patch/10322937/ [2] https://git.linaro.org/people/manivannan.sadhasivam/linux.git/log/?h=s900-for-next Changes in v8: * Modified the NACK and Bus error handling as per Wolfram's review Changes in v7: * Fixed a multi line misalignment spotted by Peter Changes in v6: As per Peter's review: * Added missing newlines for error and debug outputs * Fixed further multi-line misalignments Changes in v5: * Cleaned up the multi-line codes and reordered the error paths as per Peter's review * Added Acked-by tag from Peter for driver patch * Added Reviewed-by tag from Rob for bindings patch Changes in v4: As per Andy and Peter review: * Used spinlock for accessing most of the register access (only parts involved sleep/long-busy-wait has been excluded) * Removed returning 0 and added -ENXIO if the msg_ptr not equals to message length * Added DIV_ROUND_UP for setting clock frequency * Changed one non-atomic mdelay instance to usleep_range * Moved pinctrl definition patch before dts patch * Fixed the driver to support only 100KHz and 400KHz frequencies Changes in v3: As per Peter, Andy and Andreas review: * Removed owl_i2c_reset function from interrupt handler since it involves the use of delays. * Fixed the return path in owl_i2c_master_xfer and added a note * Changed "base" parameter to "reg" in owl_i2c_update_reg for better understandability * Ordered the includes in alphabetical order * Small changes to defines and added comma at the end of struct members * Removed rendundant 0 assignment in owl_i2c_master_xfer * Changed all OWL naming convention to Owl and also changed Actions Semi naming to Actions Semiconductor Changes in v2: As per Andy's review: * Modified infinite loops to fixed number of retries * Used i2c_8bit_addr_from_msg for constructing the slave address * Removed unnecessary parenthesis around defines * Modified certain dev_warn to dev_dbg * Modified the error handling to more generic pattern * Fixed the return value in owl_i2c_master_xfer * Added MAINTAINERS patch for I2C driver and its binding Manivannan Sadhasivam (6): dt-bindings: i2c: Add binding for Actions Semiconductor Owl I2C controller arm64: dts: actions: Add pinctrl definition for S900 I2C controller arm64: dts: actions: Add Actions Semiconductor S900 I2C controller nodes arm64: dts: actions: Enable I2C1 and I2C2 in Bubblegum-96 board i2c: Add Actions Semiconductor Owl family S900 I2C driver MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver .../devicetree/bindings/i2c/i2c-owl.txt | 27 + MAINTAINERS | 2 + .../dts/actions/s900-bubblegum-96-pins.dtsi | 29 + .../boot/dts/actions/s900-bubblegum-96.dts | 11 + arch/arm64/boot/dts/actions/s900.dtsi | 60 +++ drivers/i2c/busses/Kconfig | 7 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-owl.c | 495 ++++++++++++++++++ 8 files changed, 632 insertions(+) create mode 100644 Documentation/devicetree/bindings/i2c/i2c-owl.txt create mode 100644 arch/arm64/boot/dts/actions/s900-bubblegum-96-pins.dtsi create mode 100644 drivers/i2c/busses/i2c-owl.c -- 2.17.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html