| Message ID | 20210414154845.21964-2-srinivas.kandagatla@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | ASoC: codecs: add wcd938x support | expand |
On Wed, Apr 14, 2021 at 04:48:37PM +0100, Srinivas Kandagatla wrote: > Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC > connected over SoundWire. This device has two SoundWire device RX and > TX respectively, supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH, > 7 x TX diff inputs, 8 DMICs, MBHC. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > .../bindings/sound/qcom,wcd938x.yaml | 176 ++++++++++++++++++ > 1 file changed, 176 insertions(+) > create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml > > diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml > new file mode 100644 > index 000000000000..4c8fa8290af0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml > @@ -0,0 +1,176 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/sound/qcom,wcd938x.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Bindings for Qualcomm WCD9380/WCD9385 Audio Codec > + > +maintainers: > + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > + > +description: | > + Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC. > + It has RX and TX Soundwire slave devices. > + > +properties: > + compatible: > + enum: > + - qcom,wcd9380-codec > + - qcom,wcd9385-codec > + > + reset-gpios: > + description: GPIO spec for reset line to use > + maxItems: 1 > + > + vdd-buck-supply: > + description: A reference to the 1.8V buck supply > + > + vdd-rxtx-supply: > + description: A reference to the 1.8V rx supply > + > + vdd-io-supply: > + description: A reference to the 1.8V I/O supply > + > + qcom,tx-device: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + maxItems: 1 > + description: A reference to Soundwire tx device phandle > + > + qcom,rx-device: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + maxItems: 1 > + description: A reference to Soundwire rx device phandle > + > + qcom,micbias1-microvolt: > + description: micbias1 voltage > + minimum: 1800000 > + maximum: 2850000 > + > + qcom,micbias2-microvolt: > + description: micbias2 voltage > + minimum: 1800000 > + maximum: 2850000 > + > + qcom,micbias3-microvolt: > + description: micbias3 voltage > + minimum: 1800000 > + maximum: 2850000 > + > + qcom,micbias4-microvolt: > + description: micbias4 voltage > + minimum: 1800000 > + maximum: 2850000 > + > + qcom,mbhc-hphl-switch: > + description: Indicates that HPHL switch type is normally closed > + type: boolean > + > + qcom,mbhc-ground-switch: > + description: Indicates that Headset Ground switch type is normally closed > + type: boolean > + > + qcom,mbhc-button0-vthreshold-microvolt: > + description: Voltage threshold value headset button0 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button1-vthreshold-microvolt: > + description: Voltage threshold value headset button1 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button2-vthreshold-microvolt: > + description: Voltage threshold value headset button2 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button3-vthreshold-microvolt: > + description: Voltage threshold value headset button3 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button4-vthreshold-microvolt: > + description: Voltage threshold value headset button4 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button5-vthreshold-microvolt: > + description: Voltage threshold value headset button5 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button6-vthreshold-microvolt: > + description: Voltage threshold value headset button6 > + minimum: 0 > + maximum: 500000 > + > + qcom,mbhc-button7-vthreshold-microvolt: > + description: Voltage threshold value headset button7 > + minimum: 0 > + maximum: 500000 > + > + '#sound-dai-cells': > + const: 1 > + > +required: > + - compatible > + - reset-gpios > + - qcom,tx-device > + - qcom,rx-device > + - qcom,micbias1-microvolt > + - qcom,micbias2-microvolt > + - qcom,micbias3-microvolt > + - qcom,micbias4-microvolt > + - qcom,mbhc-hphl-switch > + - qcom,mbhc-ground-switch > + - "#sound-dai-cells" > + > +additionalProperties: false > + > +examples: > + - | > + codec { > + compatible = "qcom,wcd9380-codec"; > + reset-gpios = <&tlmm 32 0>; > + #sound-dai-cells = <1>; > + qcom,tx-device = <&wcd938x_tx>; > + qcom,rx-device = <&wcd938x_rx>; > + qcom,micbias1-microvolt = <1800000>; > + qcom,micbias2-microvolt = <1800000>; > + qcom,micbias3-microvolt = <1800000>; > + qcom,micbias4-microvolt = <1800000>; > + qcom,mbhc-hphl-switch; > + qcom,mbhc-ground-switch; > + qcom,mbhc-button0-vthreshold-microvolt = <75000>; > + qcom,mbhc-button1-vthreshold-microvolt = <150000>; > + qcom,mbhc-button2-vthreshold-microvolt = <237000>; > + qcom,mbhc-button3-vthreshold-microvolt = <500000>; > + qcom,mbhc-button5-vthreshold-microvolt = <500000>; > + qcom,mbhc-button6-vthreshold-microvolt = <500000>; > + qcom,mbhc-button7-vthreshold-microvolt = <500000>; > + }; > + > + /* ... */ > + > + soundwire@3230000 { > + #address-cells = <2>; > + #size-cells = <0>; > + reg = <0x03230000 0x2000>; > + wcd938x_tx: codec@0,3 { > + compatible = "sdw20217010d00"; > + reg = <0 3>; > + qcom,direction = "tx"; > + qcom,port-mapping = <2 3 4 5>; > + }; > + > + wcd938x_rx: codec@0,4 { > + compatible = "sdw20217010d00"; > + reg = <0 4>; > + qcom,direction = "rx"; > + qcom,port-mapping = <1 2 3 4 5>; > + }; This is a single device, right? We shouldn't need 3 nodes to describe it. I think this should all be a single node like this: codec@0,3 { reg = <0 3>, <0 4>; compatible = "sdw20217010d00"; reset-gpios = <&tlmm 32 0>; #sound-dai-cells = <1>; qcom,micbias1-microvolt = <1800000>; qcom,micbias2-microvolt = <1800000>; qcom,micbias3-microvolt = <1800000>; qcom,micbias4-microvolt = <1800000>; qcom,mbhc-hphl-switch; qcom,mbhc-ground-switch; qcom,mbhc-button0-vthreshold-microvolt = <75000>; qcom,mbhc-button1-vthreshold-microvolt = <150000>; qcom,mbhc-button2-vthreshold-microvolt = <237000>; qcom,mbhc-button3-vthreshold-microvolt = <500000>; qcom,mbhc-button5-vthreshold-microvolt = <500000>; qcom,mbhc-button6-vthreshold-microvolt = <500000>; qcom,mbhc-button7-vthreshold-microvolt = <500000>; }; You'll have to figure out the qcom,direction and qcom,port-mapping parts though. Rob
Thanks Rob for quick review, On 15/04/2021 17:29, Rob Herring wrote: > On Wed, Apr 14, 2021 at 04:48:37PM +0100, Srinivas Kandagatla wrote: >> Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC >> connected over SoundWire. This device has two SoundWire device RX and >> TX respectively, supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH, >> 7 x TX diff inputs, 8 DMICs, MBHC. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> --- >> .../bindings/sound/qcom,wcd938x.yaml | 176 ++++++++++++++++++ >> 1 file changed, 176 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >> >> diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >> new file mode 100644 >> index 000000000000..4c8fa8290af0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >> @@ -0,0 +1,176 @@ ... >> +additionalProperties: false >> + >> +examples: >> + - | >> + codec { >> + compatible = "qcom,wcd9380-codec"; >> + reset-gpios = <&tlmm 32 0>; >> + #sound-dai-cells = <1>; >> + qcom,tx-device = <&wcd938x_tx>; >> + qcom,rx-device = <&wcd938x_rx>; >> + qcom,micbias1-microvolt = <1800000>; >> + qcom,micbias2-microvolt = <1800000>; >> + qcom,micbias3-microvolt = <1800000>; >> + qcom,micbias4-microvolt = <1800000>; >> + qcom,mbhc-hphl-switch; >> + qcom,mbhc-ground-switch; >> + qcom,mbhc-button0-vthreshold-microvolt = <75000>; >> + qcom,mbhc-button1-vthreshold-microvolt = <150000>; >> + qcom,mbhc-button2-vthreshold-microvolt = <237000>; >> + qcom,mbhc-button3-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button5-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button6-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button7-vthreshold-microvolt = <500000>; >> + }; >> + >> + /* ... */ >> + >> + soundwire@3230000 { >> + #address-cells = <2>; >> + #size-cells = <0>; >> + reg = <0x03230000 0x2000>; >> + wcd938x_tx: codec@0,3 { >> + compatible = "sdw20217010d00"; >> + reg = <0 3>; >> + qcom,direction = "tx"; >> + qcom,port-mapping = <2 3 4 5>; >> + }; >> + >> + wcd938x_rx: codec@0,4 { >> + compatible = "sdw20217010d00"; >> + reg = <0 4>; >> + qcom,direction = "rx"; >> + qcom,port-mapping = <1 2 3 4 5>; >> + }; > > This is a single device, right? We shouldn't need 3 nodes to describe > it. I think this should all be a single node like this: > No, WCD938x is a Audio Codec which has two SoundWire Slave device (TX and RX). WCD938X reset lines and supplies are common for both TX and RX SoundWire devices. However TX SoundWire device only has register access to codec CSR(Control Status registers). So there are two SoundWire devices and a WCD938X common parts. Now making the common Codec part as a separate device made more sense here. So we ended with total 3 devices. 1 . WCD938x Codec which deals with all the codec side including Common parts. 2. TX SoundWire device to configure TX SoundWire ports/interface and provide CSR access. 3. RX SoundWire device to configure RX Soundwire ports/interface > codec@0,3 { > reg = <0 3>, <0 4>; We can't have this, as these two SoundWire devices hang on different SoundWire bus instances. > compatible = "sdw20217010d00"; > > reset-gpios = <&tlmm 32 0>; > #sound-dai-cells = <1>; > qcom,micbias1-microvolt = <1800000>; > qcom,micbias2-microvolt = <1800000>; > qcom,micbias3-microvolt = <1800000>; > qcom,micbias4-microvolt = <1800000>; > qcom,mbhc-hphl-switch; > qcom,mbhc-ground-switch; > qcom,mbhc-button0-vthreshold-microvolt = <75000>; > qcom,mbhc-button1-vthreshold-microvolt = <150000>; > qcom,mbhc-button2-vthreshold-microvolt = <237000>; > qcom,mbhc-button3-vthreshold-microvolt = <500000>; > qcom,mbhc-button5-vthreshold-microvolt = <500000>; > qcom,mbhc-button6-vthreshold-microvolt = <500000>; > qcom,mbhc-button7-vthreshold-microvolt = <500000>; > }; > > You'll have to figure out the qcom,direction and qcom,port-mapping parts > though. That is the reason why we ended up with 3 devices here. --srini > > Rob >
On 15/04/2021 17:29, Rob Herring wrote: >> + codec { >> + compatible = "qcom,wcd9380-codec"; >> + reset-gpios = <&tlmm 32 0>; >> + #sound-dai-cells = <1>; >> + qcom,tx-device = <&wcd938x_tx>; >> + qcom,rx-device = <&wcd938x_rx>; >> + qcom,micbias1-microvolt = <1800000>; >> + qcom,micbias2-microvolt = <1800000>; >> + qcom,micbias3-microvolt = <1800000>; >> + qcom,micbias4-microvolt = <1800000>; >> + qcom,mbhc-hphl-switch; >> + qcom,mbhc-ground-switch; >> + qcom,mbhc-button0-vthreshold-microvolt = <75000>; >> + qcom,mbhc-button1-vthreshold-microvolt = <150000>; >> + qcom,mbhc-button2-vthreshold-microvolt = <237000>; >> + qcom,mbhc-button3-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button5-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button6-vthreshold-microvolt = <500000>; >> + qcom,mbhc-button7-vthreshold-microvolt = <500000>; >> + }; >> + >> + /* ... */ >> + >> + soundwire@3230000 { >> + #address-cells = <2>; >> + #size-cells = <0>; >> + reg = <0x03230000 0x2000>; >> + wcd938x_tx: codec@0,3 { >> + compatible = "sdw20217010d00"; >> + reg = <0 3>; >> + qcom,direction = "tx"; >> + qcom,port-mapping = <2 3 4 5>; >> + }; >> + >> + wcd938x_rx: codec@0,4 { >> + compatible = "sdw20217010d00"; >> + reg = <0 4>; >> + qcom,direction = "rx"; >> + qcom,port-mapping = <1 2 3 4 5>; >> + }; > This is a single device, right? We shouldn't need 3 nodes to describe Just realized that the example is bit misleading here. It should look like: codec { compatible = "qcom,wcd9380-codec"; reset-gpios = <&tlmm 32 0>; #sound-dai-cells = <1>; qcom,tx-device = <&wcd938x_tx>; qcom,rx-device = <&wcd938x_rx>; qcom,micbias1-microvolt = <1800000>; qcom,micbias2-microvolt = <1800000>; qcom,micbias3-microvolt = <1800000>; qcom,micbias4-microvolt = <1800000>; qcom,mbhc-hphl-switch; qcom,mbhc-ground-switch; qcom,mbhc-button0-vthreshold-microvolt = <75000>; qcom,mbhc-button1-vthreshold-microvolt = <150000>; qcom,mbhc-button2-vthreshold-microvolt = <237000>; qcom,mbhc-button3-vthreshold-microvolt = <500000>; qcom,mbhc-button5-vthreshold-microvolt = <500000>; qcom,mbhc-button6-vthreshold-microvolt = <500000>; qcom,mbhc-button7-vthreshold-microvolt = <500000>; }; soundwire-controller@3230000 { reg = <0 0x3230000 0 0x2000>; compatible = "qcom,soundwire-v1.5.1"; wcd938x_tx: codec@0,3 { compatible = "sdw20217010d00"; reg = <0 3>; qcom,direction = "tx"; qcom,port-mapping = <2 3 4 5>; }; }; soundwire-controller@3210000 { reg = <0 0x3210000 0 0x2000>; compatible = "qcom,soundwire-v1.5.1"; wcd938x_rx: codec@0,4 { compatible = "sdw20217010d00"; reg = <0 4>; qcom,direction = "rx"; qcom,port-mapping = <1 2 3 4 5>; }; }; --srini
Hi Rob, On 15/04/2021 17:53, Srinivas Kandagatla wrote: > Thanks Rob for quick review, > > On 15/04/2021 17:29, Rob Herring wrote: >> On Wed, Apr 14, 2021 at 04:48:37PM +0100, Srinivas Kandagatla wrote: >>> Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC >>> connected over SoundWire. This device has two SoundWire device RX and >>> TX respectively, supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH, >>> 7 x TX diff inputs, 8 DMICs, MBHC. >>> >>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >>> --- >>> .../bindings/sound/qcom,wcd938x.yaml | 176 ++++++++++++++++++ >>> 1 file changed, 176 insertions(+) >>> create mode 100644 >>> Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >>> >>> diff --git >>> a/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >>> b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >>> new file mode 100644 >>> index 000000000000..4c8fa8290af0 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml >>> @@ -0,0 +1,176 @@ > > ... > >>> +additionalProperties: false >>> + >>> +examples: >>> + - | >>> + codec { >>> + compatible = "qcom,wcd9380-codec"; >>> + reset-gpios = <&tlmm 32 0>; >>> + #sound-dai-cells = <1>; >>> + qcom,tx-device = <&wcd938x_tx>; >>> + qcom,rx-device = <&wcd938x_rx>; >>> + qcom,micbias1-microvolt = <1800000>; >>> + qcom,micbias2-microvolt = <1800000>; >>> + qcom,micbias3-microvolt = <1800000>; >>> + qcom,micbias4-microvolt = <1800000>; >>> + qcom,mbhc-hphl-switch; >>> + qcom,mbhc-ground-switch; >>> + qcom,mbhc-button0-vthreshold-microvolt = <75000>; >>> + qcom,mbhc-button1-vthreshold-microvolt = <150000>; >>> + qcom,mbhc-button2-vthreshold-microvolt = <237000>; >>> + qcom,mbhc-button3-vthreshold-microvolt = <500000>; >>> + qcom,mbhc-button5-vthreshold-microvolt = <500000>; >>> + qcom,mbhc-button6-vthreshold-microvolt = <500000>; >>> + qcom,mbhc-button7-vthreshold-microvolt = <500000>; >>> + }; >>> + >>> + /* ... */ >>> + >>> + soundwire@3230000 { >>> + #address-cells = <2>; >>> + #size-cells = <0>; >>> + reg = <0x03230000 0x2000>; >>> + wcd938x_tx: codec@0,3 { >>> + compatible = "sdw20217010d00"; >>> + reg = <0 3>; >>> + qcom,direction = "tx"; >>> + qcom,port-mapping = <2 3 4 5>; >>> + }; >>> + >>> + wcd938x_rx: codec@0,4 { >>> + compatible = "sdw20217010d00"; >>> + reg = <0 4>; >>> + qcom,direction = "rx"; >>> + qcom,port-mapping = <1 2 3 4 5>; >>> + }; >> >> This is a single device, right? We shouldn't need 3 nodes to describe >> it. I think this should all be a single node like this: >> > No, WCD938x is a Audio Codec which has two SoundWire Slave device (TX > and RX). WCD938X reset lines and supplies are common for both TX and RX > SoundWire devices. > > However TX SoundWire device only has register access to codec > CSR(Control Status registers). > > So there are two SoundWire devices and a WCD938X common parts. Now > making the common Codec part as a separate device made more sense here. > So we ended with total 3 devices. > > 1 . WCD938x Codec which deals with all the codec side including Common > parts. > 2. TX SoundWire device to configure TX SoundWire ports/interface and > provide CSR access. > 3. RX SoundWire device to configure RX Soundwire ports/interface > Are you okay with the existing device layout after providing the above information? codec { compatible = "qcom,wcd9380-codec"; reset-gpios = <&tlmm 32 0>; #sound-dai-cells = <1>; qcom,tx-device = <&wcd938x_tx>; qcom,rx-device = <&wcd938x_rx>; qcom,micbias1-microvolt = <1800000>; qcom,micbias2-microvolt = <1800000>; qcom,micbias3-microvolt = <1800000>; qcom,micbias4-microvolt = <1800000>; qcom,mbhc-hphl-switch; qcom,mbhc-ground-switch; qcom,mbhc-button0-vthreshold-microvolt = <75000>; qcom,mbhc-button1-vthreshold-microvolt = <150000>; qcom,mbhc-button2-vthreshold-microvolt = <237000>; qcom,mbhc-button3-vthreshold-microvolt = <500000>; qcom,mbhc-button5-vthreshold-microvolt = <500000>; qcom,mbhc-button6-vthreshold-microvolt = <500000>; qcom,mbhc-button7-vthreshold-microvolt = <500000>; }; soundwire-controller@3230000 { reg = <0 0x3230000 0 0x2000>; compatible = "qcom,soundwire-v1.5.1"; wcd938x_tx: codec@0,3 { compatible = "sdw20217010d00"; reg = <0 3>; qcom,direction = "tx"; qcom,port-mapping = <2 3 4 5>; }; }; soundwire-controller@3210000 { reg = <0 0x3210000 0 0x2000>; compatible = "qcom,soundwire-v1.5.1"; wcd938x_rx: codec@0,4 { compatible = "sdw20217010d00"; reg = <0 4>; qcom,direction = "rx"; qcom,port-mapping = <1 2 3 4 5>; }; }; thanks, srini > >> codec@0,3 { >> reg = <0 3>, <0 4>; > > We can't have this, as these two SoundWire devices hang on different > SoundWire bus instances. > >> compatible = "sdw20217010d00"; >> >> reset-gpios = <&tlmm 32 0>; >> #sound-dai-cells = <1>; >> qcom,micbias1-microvolt = <1800000>; >> qcom,micbias2-microvolt = <1800000>; >> qcom,micbias3-microvolt = <1800000>; >> qcom,micbias4-microvolt = <1800000>; >> qcom,mbhc-hphl-switch; >> qcom,mbhc-ground-switch; >> qcom,mbhc-button0-vthreshold-microvolt = <75000>; >> qcom,mbhc-button1-vthreshold-microvolt = <150000>; >> qcom,mbhc-button2-vthreshold-microvolt = <237000>; >> qcom,mbhc-button3-vthreshold-microvolt = <500000>; >> qcom,mbhc-button5-vthreshold-microvolt = <500000>; >> qcom,mbhc-button6-vthreshold-microvolt = <500000>; >> qcom,mbhc-button7-vthreshold-microvolt = <500000>; >> }; >> >> You'll have to figure out the qcom,direction and qcom,port-mapping parts >> though. > > That is the reason why we ended up with 3 devices here. > > --srini >> >> Rob >>
diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml new file mode 100644 index 000000000000..4c8fa8290af0 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml @@ -0,0 +1,176 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/qcom,wcd938x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for Qualcomm WCD9380/WCD9385 Audio Codec + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC. + It has RX and TX Soundwire slave devices. + +properties: + compatible: + enum: + - qcom,wcd9380-codec + - qcom,wcd9385-codec + + reset-gpios: + description: GPIO spec for reset line to use + maxItems: 1 + + vdd-buck-supply: + description: A reference to the 1.8V buck supply + + vdd-rxtx-supply: + description: A reference to the 1.8V rx supply + + vdd-io-supply: + description: A reference to the 1.8V I/O supply + + qcom,tx-device: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: A reference to Soundwire tx device phandle + + qcom,rx-device: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: A reference to Soundwire rx device phandle + + qcom,micbias1-microvolt: + description: micbias1 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias2-microvolt: + description: micbias2 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias3-microvolt: + description: micbias3 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias4-microvolt: + description: micbias4 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,mbhc-hphl-switch: + description: Indicates that HPHL switch type is normally closed + type: boolean + + qcom,mbhc-ground-switch: + description: Indicates that Headset Ground switch type is normally closed + type: boolean + + qcom,mbhc-button0-vthreshold-microvolt: + description: Voltage threshold value headset button0 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button1-vthreshold-microvolt: + description: Voltage threshold value headset button1 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button2-vthreshold-microvolt: + description: Voltage threshold value headset button2 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button3-vthreshold-microvolt: + description: Voltage threshold value headset button3 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button4-vthreshold-microvolt: + description: Voltage threshold value headset button4 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button5-vthreshold-microvolt: + description: Voltage threshold value headset button5 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button6-vthreshold-microvolt: + description: Voltage threshold value headset button6 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button7-vthreshold-microvolt: + description: Voltage threshold value headset button7 + minimum: 0 + maximum: 500000 + + '#sound-dai-cells': + const: 1 + +required: + - compatible + - reset-gpios + - qcom,tx-device + - qcom,rx-device + - qcom,micbias1-microvolt + - qcom,micbias2-microvolt + - qcom,micbias3-microvolt + - qcom,micbias4-microvolt + - qcom,mbhc-hphl-switch + - qcom,mbhc-ground-switch + - "#sound-dai-cells" + +additionalProperties: false + +examples: + - | + codec { + compatible = "qcom,wcd9380-codec"; + reset-gpios = <&tlmm 32 0>; + #sound-dai-cells = <1>; + qcom,tx-device = <&wcd938x_tx>; + qcom,rx-device = <&wcd938x_rx>; + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + qcom,mbhc-hphl-switch; + qcom,mbhc-ground-switch; + qcom,mbhc-button0-vthreshold-microvolt = <75000>; + qcom,mbhc-button1-vthreshold-microvolt = <150000>; + qcom,mbhc-button2-vthreshold-microvolt = <237000>; + qcom,mbhc-button3-vthreshold-microvolt = <500000>; + qcom,mbhc-button5-vthreshold-microvolt = <500000>; + qcom,mbhc-button6-vthreshold-microvolt = <500000>; + qcom,mbhc-button7-vthreshold-microvolt = <500000>; + }; + + /* ... */ + + soundwire@3230000 { + #address-cells = <2>; + #size-cells = <0>; + reg = <0x03230000 0x2000>; + wcd938x_tx: codec@0,3 { + compatible = "sdw20217010d00"; + reg = <0 3>; + qcom,direction = "tx"; + qcom,port-mapping = <2 3 4 5>; + }; + + wcd938x_rx: codec@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + qcom,direction = "rx"; + qcom,port-mapping = <1 2 3 4 5>; + }; + + }; + +...
Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC connected over SoundWire. This device has two SoundWire device RX and TX respectively, supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH, 7 x TX diff inputs, 8 DMICs, MBHC. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- .../bindings/sound/qcom,wcd938x.yaml | 176 ++++++++++++++++++ 1 file changed, 176 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml -- 2.21.0