| Message ID | 20210518232858.1535403-6-robh@kernel.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | dt-bindings: Convert mux bindings to schema | expand |
Hi Rob, Thank you for the patch. On Tue, May 18, 2021 at 06:28:57PM -0500, Rob Herring wrote: > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Signed-off-by: Rob Herring <robh@kernel.org> > --- > .../bindings/i2c/i2c-mux-pca954x.txt | 74 ------------ > .../bindings/i2c/i2c-mux-pca954x.yaml | 106 ++++++++++++++++++ > 2 files changed, 106 insertions(+), 74 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > deleted file mode 100644 > index 9f3f3eb67e87..000000000000 > --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > +++ /dev/null > @@ -1,74 +0,0 @@ > -* NXP PCA954x I2C bus switch > - > -The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. > - > -Required Properties: > - > - - compatible: Must contain one of the following. > - "nxp,pca9540", > - "nxp,pca9542", > - "nxp,pca9543", > - "nxp,pca9544", > - "nxp,pca9545", > - "nxp,pca9546", "nxp,pca9846", > - "nxp,pca9547", "nxp,pca9847", > - "nxp,pca9548", "nxp,pca9848", > - "nxp,pca9849" > - > - - reg: The I2C address of the device. > - > - The following required properties are defined externally: > - > - - Standard I2C mux properties. See i2c-mux.txt in this directory. > - - I2C child bus nodes. See i2c-mux.txt in this directory. > - > -Optional Properties: > - > - - reset-gpios: Reference to the GPIO connected to the reset input. > - - idle-state: if present, overrides i2c-mux-idle-disconnect, > - Please refer to Documentation/devicetree/bindings/mux/mux-controller.yaml > - - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all > - children in idle state. This is necessary for example, if there are several > - multiplexers on the bus and the devices behind them use same I2C addresses. > - - interrupts: Interrupt mapping for IRQ. > - - interrupt-controller: Marks the device node as an interrupt controller. > - - #interrupt-cells : Should be two. > - - first cell is the pin number > - - second cell is used to specify flags. > - See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt > - > -Example: > - > - i2c-switch@74 { > - compatible = "nxp,pca9548"; > - #address-cells = <1>; > - #size-cells = <0>; > - reg = <0x74>; > - > - interrupt-parent = <&ipic>; > - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; > - interrupt-controller; > - #interrupt-cells = <2>; > - > - i2c@2 { > - #address-cells = <1>; > - #size-cells = <0>; > - reg = <2>; > - > - eeprom@54 { > - compatible = "atmel,24c08"; > - reg = <0x54>; > - }; > - }; > - > - i2c@4 { > - #address-cells = <1>; > - #size-cells = <0>; > - reg = <4>; > - > - rtc@51 { > - compatible = "nxp,pcf8563"; > - reg = <0x51>; > - }; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > new file mode 100644 > index 000000000000..82d9101098c7 > --- /dev/null > +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > @@ -0,0 +1,106 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: NXP PCA954x I2C bus switch > + > +maintainers: > + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> > + > +description: > + The binding supports NXP PCA954x and PCA984x I2C mux/switch devices. > + > +allOf: > + - $ref: /schemas/i2c/i2c-mux.yaml# > + > +properties: > + compatible: > + enum: > + - nxp,pca9540 > + - nxp,pca9542 > + - nxp,pca9543 > + - nxp,pca9544 > + - nxp,pca9545 > + - nxp,pca9546 > + - nxp,pca9547 > + - nxp,pca9548 > + - nxp,pca9849 I'd put this entry last to keep them alphabetically sorted. While at it, could you add nxp,pca9646 as the driver supports it ? Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > + - nxp,pca9846 > + - nxp,pca9847 > + - nxp,pca9848 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + "#interrupt-cells": > + const: 2 > + > + interrupt-controller: true > + > + reset-gpios: > + maxItems: 1 > + > + i2c-mux-idle-disconnect: > + type: boolean > + description: Forces mux to disconnect all children in idle state. This is > + necessary for example, if there are several multiplexers on the bus and > + the devices behind them use same I2C addresses. > + > + idle-state: > + description: if present, overrides i2c-mux-idle-disconnect > + $ref: /schemas/mux/mux-controller.yaml#/properties/idle-state > + > +required: > + - compatible > + - reg > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + i2c-mux@74 { > + compatible = "nxp,pca9548"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x74>; > + > + interrupt-parent = <&ipic>; > + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <2>; > + > + eeprom@54 { > + compatible = "atmel,24c08"; > + reg = <0x54>; > + }; > + }; > + > + i2c@4 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <4>; > + > + rtc@51 { > + compatible = "nxp,pcf8563"; > + reg = <0x51>; > + }; > + }; > + }; > + }; > +... -- Regards, Laurent Pinchart
On Tue, May 18, 2021 at 8:23 PM Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > > Hi Rob, > > Thank you for the patch. > > On Tue, May 18, 2021 at 06:28:57PM -0500, Rob Herring wrote: > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Signed-off-by: Rob Herring <robh@kernel.org> > > --- > > .../bindings/i2c/i2c-mux-pca954x.txt | 74 ------------ > > .../bindings/i2c/i2c-mux-pca954x.yaml | 106 ++++++++++++++++++ > > 2 files changed, 106 insertions(+), 74 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > > create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > > deleted file mode 100644 > > index 9f3f3eb67e87..000000000000 > > --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt > > +++ /dev/null > > @@ -1,74 +0,0 @@ > > -* NXP PCA954x I2C bus switch > > - > > -The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. > > - > > -Required Properties: > > - > > - - compatible: Must contain one of the following. > > - "nxp,pca9540", > > - "nxp,pca9542", > > - "nxp,pca9543", > > - "nxp,pca9544", > > - "nxp,pca9545", > > - "nxp,pca9546", "nxp,pca9846", > > - "nxp,pca9547", "nxp,pca9847", > > - "nxp,pca9548", "nxp,pca9848", > > - "nxp,pca9849" > > - > > - - reg: The I2C address of the device. > > - > > - The following required properties are defined externally: > > - > > - - Standard I2C mux properties. See i2c-mux.txt in this directory. > > - - I2C child bus nodes. See i2c-mux.txt in this directory. > > - > > -Optional Properties: > > - > > - - reset-gpios: Reference to the GPIO connected to the reset input. > > - - idle-state: if present, overrides i2c-mux-idle-disconnect, > > - Please refer to Documentation/devicetree/bindings/mux/mux-controller.yaml > > - - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all > > - children in idle state. This is necessary for example, if there are several > > - multiplexers on the bus and the devices behind them use same I2C addresses. > > - - interrupts: Interrupt mapping for IRQ. > > - - interrupt-controller: Marks the device node as an interrupt controller. > > - - #interrupt-cells : Should be two. > > - - first cell is the pin number > > - - second cell is used to specify flags. > > - See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt > > - > > -Example: > > - > > - i2c-switch@74 { > > - compatible = "nxp,pca9548"; > > - #address-cells = <1>; > > - #size-cells = <0>; > > - reg = <0x74>; > > - > > - interrupt-parent = <&ipic>; > > - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; > > - interrupt-controller; > > - #interrupt-cells = <2>; > > - > > - i2c@2 { > > - #address-cells = <1>; > > - #size-cells = <0>; > > - reg = <2>; > > - > > - eeprom@54 { > > - compatible = "atmel,24c08"; > > - reg = <0x54>; > > - }; > > - }; > > - > > - i2c@4 { > > - #address-cells = <1>; > > - #size-cells = <0>; > > - reg = <4>; > > - > > - rtc@51 { > > - compatible = "nxp,pcf8563"; > > - reg = <0x51>; > > - }; > > - }; > > - }; > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > new file mode 100644 > > index 000000000000..82d9101098c7 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > @@ -0,0 +1,106 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: NXP PCA954x I2C bus switch > > + > > +maintainers: > > + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > + > > +description: > > + The binding supports NXP PCA954x and PCA984x I2C mux/switch devices. > > + > > +allOf: > > + - $ref: /schemas/i2c/i2c-mux.yaml# > > + > > +properties: > > + compatible: > > + enum: > > + - nxp,pca9540 > > + - nxp,pca9542 > > + - nxp,pca9543 > > + - nxp,pca9544 > > + - nxp,pca9545 > > + - nxp,pca9546 > > + - nxp,pca9547 > > + - nxp,pca9548 > > + - nxp,pca9849 > > I'd put this entry last to keep them alphabetically sorted. Sigh, that was my intent... > While at it, could you add nxp,pca9646 as the driver supports it ? Sure. > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Thanks!
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt deleted file mode 100644 index 9f3f3eb67e87..000000000000 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ /dev/null @@ -1,74 +0,0 @@ -* NXP PCA954x I2C bus switch - -The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. - -Required Properties: - - - compatible: Must contain one of the following. - "nxp,pca9540", - "nxp,pca9542", - "nxp,pca9543", - "nxp,pca9544", - "nxp,pca9545", - "nxp,pca9546", "nxp,pca9846", - "nxp,pca9547", "nxp,pca9847", - "nxp,pca9548", "nxp,pca9848", - "nxp,pca9849" - - - reg: The I2C address of the device. - - The following required properties are defined externally: - - - Standard I2C mux properties. See i2c-mux.txt in this directory. - - I2C child bus nodes. See i2c-mux.txt in this directory. - -Optional Properties: - - - reset-gpios: Reference to the GPIO connected to the reset input. - - idle-state: if present, overrides i2c-mux-idle-disconnect, - Please refer to Documentation/devicetree/bindings/mux/mux-controller.yaml - - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all - children in idle state. This is necessary for example, if there are several - multiplexers on the bus and the devices behind them use same I2C addresses. - - interrupts: Interrupt mapping for IRQ. - - interrupt-controller: Marks the device node as an interrupt controller. - - #interrupt-cells : Should be two. - - first cell is the pin number - - second cell is used to specify flags. - See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - -Example: - - i2c-switch@74 { - compatible = "nxp,pca9548"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x74>; - - interrupt-parent = <&ipic>; - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - interrupt-controller; - #interrupt-cells = <2>; - - i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; - - eeprom@54 { - compatible = "atmel,24c08"; - reg = <0x54>; - }; - }; - - i2c@4 { - #address-cells = <1>; - #size-cells = <0>; - reg = <4>; - - rtc@51 { - compatible = "nxp,pcf8563"; - reg = <0x51>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml new file mode 100644 index 000000000000..82d9101098c7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP PCA954x I2C bus switch + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: + The binding supports NXP PCA954x and PCA984x I2C mux/switch devices. + +allOf: + - $ref: /schemas/i2c/i2c-mux.yaml# + +properties: + compatible: + enum: + - nxp,pca9540 + - nxp,pca9542 + - nxp,pca9543 + - nxp,pca9544 + - nxp,pca9545 + - nxp,pca9546 + - nxp,pca9547 + - nxp,pca9548 + - nxp,pca9849 + - nxp,pca9846 + - nxp,pca9847 + - nxp,pca9848 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + + reset-gpios: + maxItems: 1 + + i2c-mux-idle-disconnect: + type: boolean + description: Forces mux to disconnect all children in idle state. This is + necessary for example, if there are several multiplexers on the bus and + the devices behind them use same I2C addresses. + + idle-state: + description: if present, overrides i2c-mux-idle-disconnect + $ref: /schemas/mux/mux-controller.yaml#/properties/idle-state + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + i2c-mux@74 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + + interrupt-parent = <&ipic>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + eeprom@54 { + compatible = "atmel,24c08"; + reg = <0x54>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; + }; +...
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Rob Herring <robh@kernel.org> --- .../bindings/i2c/i2c-mux-pca954x.txt | 74 ------------ .../bindings/i2c/i2c-mux-pca954x.yaml | 106 ++++++++++++++++++ 2 files changed, 106 insertions(+), 74 deletions(-) delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml -- 2.27.0