similarity index 98%
copy from arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
copy to arch/arm64/boot/dts/renesas/ebisu.dtsi
@@ -1,18 +1,16 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Device Tree Source for the Ebisu board with R-Car E3
+ * Device Tree Source for the Ebisu board
*
* Copyright (C) 2018 Renesas Electronics Corp.
*/
-/dts-v1/;
-#include "r8a77990.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
- model = "Renesas Ebisu board based on r8a77990";
- compatible = "renesas,ebisu", "renesas,r8a77990";
+ model = "Renesas Ebisu board";
+ compatible = "renesas,ebisu";
aliases {
serial0 = &scif2;
@@ -313,7 +311,7 @@ phy0: ethernet-phy@0 {
* TX clock internal delay mode is required for reliable
* 1Gbps communication using the KSZ9031RNX phy present on
* the Ebisu board, however, TX clock internal delay mode
- * isn't supported on r8a77990. Thus, limit speed to
+ * isn't supported on R-Car E3(e). Thus, limit speed to
* 100Mbps for reliable communication.
*/
max-speed = <100>;
@@ -7,795 +7,9 @@
/dts-v1/;
#include "r8a77990.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ebisu.dtsi"
/ {
model = "Renesas Ebisu board based on r8a77990";
compatible = "renesas,ebisu", "renesas,r8a77990";
-
- aliases {
- serial0 = &scif2;
- ethernet0 = &avb;
- mmc0 = &sdhi3;
- mmc1 = &sdhi0;
- mmc2 = &sdhi1;
- };
-
- chosen {
- bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
- stdout-path = "serial0:115200n8";
- };
-
- audio_clkout: audio-clkout {
- /*
- * This is same as <&rcar_sound 0>
- * but needed to avoid cs2000/rcar_sound probe dead-lock
- */
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <11289600>;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm3 0 50000>;
-
- brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
- default-brightness-level = <10>;
-
- power-supply = <®_12p0v>;
- };
-
- cvbs-in {
- compatible = "composite-video-connector";
- label = "CVBS IN";
-
- port {
- cvbs_con: endpoint {
- remote-endpoint = <&adv7482_ain7>;
- };
- };
- };
-
- hdmi-in {
- compatible = "hdmi-connector";
- label = "HDMI IN";
- type = "a";
-
- port {
- hdmi_in_con: endpoint {
- remote-endpoint = <&adv7482_hdmi>;
- };
- };
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con_out: endpoint {
- remote-endpoint = <&adv7511_out>;
- };
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&keys_pins>;
- pinctrl-names = "default";
-
- key-1 {
- gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_1>;
- label = "SW4-1";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-2 {
- gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_2>;
- label = "SW4-2";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-3 {
- gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_3>;
- label = "SW4-3";
- wakeup-source;
- debounce-interval = <20>;
- };
- key-4 {
- gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_4>;
- label = "SW4-4";
- wakeup-source;
- debounce-interval = <20>;
- };
- };
-
- lvds-decoder {
- compatible = "thine,thc63lvd1024";
- vcc-supply = <®_3p3v>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- thc63lvd1024_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
-
- port@2 {
- reg = <2>;
- thc63lvd1024_out: endpoint {
- remote-endpoint = <&adv7511_in>;
- };
- };
- };
- };
-
- memory@48000000 {
- device_type = "memory";
- /* first 128MB is reserved for secure area. */
- reg = <0x0 0x48000000 0x0 0x38000000>;
- };
-
- reg_1p8v: regulator0 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_3p3v: regulator1 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_12p0v: regulator2 {
- compatible = "regulator-fixed";
- regulator-name = "D12.0V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- rsnd_ak4613: sound {
- compatible = "simple-audio-card";
-
- simple-audio-card,name = "rsnd-ak4613";
- simple-audio-card,format = "left_j";
- simple-audio-card,bitclock-master = <&sndcpu>;
- simple-audio-card,frame-master = <&sndcpu>;
-
- sndcodec: simple-audio-card,codec {
- sound-dai = <&ak4613>;
- };
-
- sndcpu: simple-audio-card,cpu {
- sound-dai = <&rcar_sound>;
- };
- };
-
- vbus0_usb2: regulator-vbus0-usb2 {
- compatible = "regulator-fixed";
-
- regulator-name = "USB20_VBUS_CN";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
-
- gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vcc_sdhi0: regulator-vcc-sdhi0 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi0: regulator-vccq-sdhi0 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI0 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1>, <1800000 0>;
- };
-
- vcc_sdhi1: regulator-vcc-sdhi1 {
- compatible = "regulator-fixed";
-
- regulator-name = "SDHI1 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vccq_sdhi1: regulator-vccq-sdhi1 {
- compatible = "regulator-gpio";
-
- regulator-name = "SDHI1 VccQ";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
- gpios-states = <1>;
- states = <3300000 1>, <1800000 0>;
- };
-
- vga {
- compatible = "vga-connector";
-
- port {
- vga_in: endpoint {
- remote-endpoint = <&adv7123_out>;
- };
- };
- };
-
- vga-encoder {
- compatible = "adi,adv7123";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7123_in: endpoint {
- remote-endpoint = <&du_out_rgb>;
- };
- };
- port@1 {
- reg = <1>;
- adv7123_out: endpoint {
- remote-endpoint = <&vga_in>;
- };
- };
- };
- };
-
- x12_clk: x12 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24576000>;
- };
-
- x13_clk: x13 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <74250000>;
- };
-};
-
-&audio_clk_a {
- clock-frequency = <22579200>;
-};
-
-&avb {
- pinctrl-0 = <&avb_pins>;
- pinctrl-names = "default";
- phy-handle = <&phy0>;
- status = "okay";
-
- phy0: ethernet-phy@0 {
- rxc-skew-ps = <1500>;
- reg = <0>;
- interrupt-parent = <&gpio2>;
- interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
- /*
- * TX clock internal delay mode is required for reliable
- * 1Gbps communication using the KSZ9031RNX phy present on
- * the Ebisu board, however, TX clock internal delay mode
- * isn't supported on r8a77990. Thus, limit speed to
- * 100Mbps for reliable communication.
- */
- max-speed = <100>;
- };
-};
-
-&canfd {
- pinctrl-0 = <&canfd0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- channel0 {
- status = "okay";
- };
-};
-
-&csi40 {
- status = "okay";
-
- ports {
- port@0 {
- csi40_in: endpoint {
- clock-lanes = <0>;
- data-lanes = <1 2>;
- remote-endpoint = <&adv7482_txa>;
- };
- };
- };
-};
-
-&du {
- pinctrl-0 = <&du_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- clocks = <&cpg CPG_MOD 724>,
- <&cpg CPG_MOD 723>,
- <&x13_clk>;
- clock-names = "du.0", "du.1", "dclkin.0";
-
- ports {
- port@0 {
- endpoint {
- remote-endpoint = <&adv7123_in>;
- };
- };
- };
-};
-
-&ehci0 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&extal_clk {
- clock-frequency = <48000000>;
-};
-
-&hsusb {
- dr_mode = "otg";
- status = "okay";
-};
-
-&i2c0 {
- status = "okay";
-
- io_expander: gpio@20 {
- compatible = "onnn,pca9654";
- reg = <0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-parent = <&gpio2>;
- interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
- };
-
- hdmi-encoder@39 {
- compatible = "adi,adv7511w";
- reg = <0x39>;
- interrupt-parent = <&gpio1>;
- interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
-
- adi,input-depth = <8>;
- adi,input-colorspace = "rgb";
- adi,input-clock = "1x";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- adv7511_in: endpoint {
- remote-endpoint = <&thc63lvd1024_out>;
- };
- };
-
- port@1 {
- reg = <1>;
- adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con_out>;
- };
- };
- };
- };
-
- video-receiver@70 {
- compatible = "adi,adv7482";
- reg = <0x70>;
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- interrupt-parent = <&gpio0>;
- interrupt-names = "intrq1", "intrq2";
- interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
- <17 IRQ_TYPE_LEVEL_LOW>;
-
- port@7 {
- reg = <7>;
-
- adv7482_ain7: endpoint {
- remote-endpoint = <&cvbs_con>;
- };
- };
-
- port@8 {
- reg = <8>;
-
- adv7482_hdmi: endpoint {
- remote-endpoint = <&hdmi_in_con>;
- };
- };
-
- port@a {
- reg = <10>;
-
- adv7482_txa: endpoint {
- clock-lanes = <0>;
- data-lanes = <1 2>;
- remote-endpoint = <&csi40_in>;
- };
- };
- };
-};
-
-&i2c3 {
- status = "okay";
-
- ak4613: codec@10 {
- compatible = "asahi-kasei,ak4613";
- #sound-dai-cells = <0>;
- reg = <0x10>;
- clocks = <&rcar_sound 3>;
-
- asahi-kasei,in1-single-end;
- asahi-kasei,in2-single-end;
- asahi-kasei,out1-single-end;
- asahi-kasei,out2-single-end;
- asahi-kasei,out3-single-end;
- asahi-kasei,out4-single-end;
- asahi-kasei,out5-single-end;
- asahi-kasei,out6-single-end;
- };
-
- cs2000: clk-multiplier@4f {
- #clock-cells = <0>;
- compatible = "cirrus,cs2000-cp";
- reg = <0x4f>;
- clocks = <&audio_clkout>, <&x12_clk>;
- clock-names = "clk_in", "ref_clk";
-
- assigned-clocks = <&cs2000>;
- assigned-clock-rates = <24576000>; /* 1/1 divide */
- };
-};
-
-&i2c_dvfs {
- status = "okay";
-
- clock-frequency = <400000>;
-
- pmic: pmic@30 {
- pinctrl-0 = <&irq0_pins>;
- pinctrl-names = "default";
-
- compatible = "rohm,bd9571mwv";
- reg = <0x30>;
- interrupt-parent = <&intc_ex>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- rohm,ddr-backup-power = <0x1>;
- rohm,rstbmode-level;
- };
-
- eeprom@50 {
- compatible = "rohm,br24t01", "atmel,24c01";
- reg = <0x50>;
- pagesize = <8>;
- };
-};
-
-&lvds0 {
- status = "okay";
-
- clocks = <&cpg CPG_MOD 727>,
- <&x13_clk>,
- <&extal_clk>;
- clock-names = "fck", "dclkin.0", "extal";
-
- ports {
- port@1 {
- lvds0_out: endpoint {
- remote-endpoint = <&thc63lvd1024_in>;
- };
- };
- };
-};
-
-&lvds1 {
- /*
- * Even though the LVDS1 output is not connected, the encoder must be
- * enabled to supply a pixel clock to the DU for the DPAD output when
- * LVDS0 is in use.
- */
- status = "okay";
-
- clocks = <&cpg CPG_MOD 727>,
- <&x13_clk>,
- <&extal_clk>;
- clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&pcie_bus_clk {
- clock-frequency = <100000000>;
-};
-
-&pciec0 {
- status = "okay";
-};
-
-&pfc {
- avb_pins: avb {
- groups = "avb_link", "avb_mii";
- function = "avb";
- };
-
- canfd0_pins: canfd0 {
- groups = "canfd0_data";
- function = "canfd0";
- };
-
- du_pins: du {
- groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
- function = "du";
- };
-
- irq0_pins: irq0 {
- groups = "intc_ex_irq0";
- function = "intc_ex";
- };
-
- keys_pins: keys {
- pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
- bias-pull-up;
- };
-
- pwm3_pins: pwm3 {
- groups = "pwm3_b";
- function = "pwm3";
- };
-
- pwm5_pins: pwm5 {
- groups = "pwm5_a";
- function = "pwm5";
- };
-
- scif2_pins: scif2 {
- groups = "scif2_data_a";
- function = "scif2";
- };
-
- sdhi0_pins: sd0 {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <3300>;
- };
-
- sdhi0_pins_uhs: sd0_uhs {
- groups = "sdhi0_data4", "sdhi0_ctrl";
- function = "sdhi0";
- power-source = <1800>;
- };
-
- sdhi1_pins: sd1 {
- groups = "sdhi1_data4", "sdhi1_ctrl";
- function = "sdhi1";
- power-source = <3300>;
- };
-
- sdhi1_pins_uhs: sd1_uhs {
- groups = "sdhi1_data4", "sdhi1_ctrl";
- function = "sdhi1";
- power-source = <1800>;
- };
-
- sdhi3_pins: sd3 {
- groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
- function = "sdhi3";
- power-source = <1800>;
- };
-
- sound_clk_pins: sound_clk {
- groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
- "audio_clkout_a", "audio_clkout1_a";
- function = "audio_clk";
- };
-
- sound_pins: sound {
- groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
- function = "ssi";
- };
-
- usb0_pins: usb {
- groups = "usb0_b", "usb0_id";
- function = "usb0";
- };
-
- usb30_pins: usb30 {
- groups = "usb30";
- function = "usb30";
- };
-};
-
-&pwm3 {
- pinctrl-0 = <&pwm3_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&pwm5 {
- pinctrl-0 = <&pwm5_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&rcar_sound {
- pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
- pinctrl-names = "default";
-
- /* Single DAI */
- #sound-dai-cells = <0>;
-
- /* audio_clkout0/1/2/3 */
- #clock-cells = <1>;
- clock-frequency = <12288000 11289600>;
-
- status = "okay";
-
- /* update <audio_clk_b> to <cs2000> */
- clocks = <&cpg CPG_MOD 1005>,
- <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
- <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
- <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
- <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
- <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
- <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
- <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
- <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
- <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
- <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
- <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
- <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
- <&cpg CPG_CORE R8A77990_CLK_ZA2>;
-
- rcar_sound,dai {
- dai0 {
- playback = <&ssi0>, <&src0>, <&dvc0>;
- capture = <&ssi1>, <&src1>, <&dvc1>;
- };
- };
-
-};
-
-&rwdt {
- timeout-sec = <60>;
- status = "okay";
-};
-
-&scif2 {
- pinctrl-0 = <&scif2_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-1 = <&sdhi0_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi0>;
- vqmmc-supply = <&vccq_sdhi0>;
- cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
- bus-width = <4>;
- sd-uhs-sdr50;
- sd-uhs-sdr104;
- status = "okay";
-};
-
-&sdhi1 {
- pinctrl-0 = <&sdhi1_pins>;
- pinctrl-1 = <&sdhi1_pins_uhs>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <&vcc_sdhi1>;
- vqmmc-supply = <&vccq_sdhi1>;
- cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- sd-uhs-sdr50;
- sd-uhs-sdr104;
- status = "okay";
-};
-
-&sdhi3 {
- /* used for on-board 8bit eMMC */
- pinctrl-0 = <&sdhi3_pins>;
- pinctrl-1 = <&sdhi3_pins>;
- pinctrl-names = "default", "state_uhs";
-
- vmmc-supply = <®_3p3v>;
- vqmmc-supply = <®_1p8v>;
- mmc-hs200-1_8v;
- mmc-hs400-1_8v;
- bus-width = <8>;
- no-sd;
- no-sdio;
- non-removable;
- full-pwr-cycle-in-suspend;
- status = "okay";
-};
-
-&ssi1 {
- shared-pin;
-};
-
-&usb2_phy0 {
- pinctrl-0 = <&usb0_pins>;
- pinctrl-names = "default";
-
- vbus-supply = <&vbus0_usb2>;
- status = "okay";
-};
-
-&usb3_peri0 {
- companion = <&xhci0>;
- status = "okay";
-};
-
-&vin4 {
- status = "okay";
-};
-
-&vin5 {
- status = "okay";
-};
-
-&xhci0 {
- pinctrl-0 = <&usb30_pins>;
- pinctrl-names = "default";
-
- status = "okay";
};