diff --git a/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt
new file mode 100644
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt
@@ -0,0 +1,47 @@
+* Pin configuration for TI IODELAY controller
+
+TI dra7 based SoCs such as am57xx have a controller for setting the IO delay
+for each pin. For most part the IO delay values are programmed by the bootloader,
+but some pins need to be configured dynamically by the kernel such as the
+MMC pins.
+
+Required Properties:
+
+  - compatible: Must be "ti,dra7-iodelay"
+  - reg: Base address and length of the memory resource used
+  - #address-cells: Number of address cells
+  - #size-cells: Size of cells
+  - #pinctrl-cells: Number of pinctrl cells, must be 2. See also
+    Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example
+-------
+
+In the SoC specific dtsi file:
+
+	dra7_iodelay_core: padconf@4844a000 {
+		compatible = "ti,dra7-iodelay";
+		reg = <0x4844a000 0x0d1c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#pinctrl-cells = <2>;
+	};
+
+In board-specific file:
+
+&dra7_iodelay_core {
+	mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf {
+		pinctrl-pin-array = <
+		0x18c A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A19_IN */
+		0x1a4 A_DELAY_PS(265) G_DELAY_PS(360)	/* CFG_GPMC_A20_IN */
+		0x1b0 A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A21_IN */
+		0x1bc A_DELAY_PS(0) G_DELAY_PS(120)	/* CFG_GPMC_A22_IN */
+		0x1c8 A_DELAY_PS(287) G_DELAY_PS(420)	/* CFG_GPMC_A23_IN */
+		0x1d4 A_DELAY_PS(144) G_DELAY_PS(240)	/* CFG_GPMC_A24_IN */
+		0x1e0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_A25_IN */
+		0x1ec A_DELAY_PS(120) G_DELAY_PS(0)	/* CFG_GPMC_A26_IN */
+		0x1f8 A_DELAY_PS(120) G_DELAY_PS(180)	/* CFG_GPMC_A27_IN */
+		0x360 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_GPMC_CS1_IN */
+		>;
+	};
+};
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -300,6 +300,7 @@ source "drivers/pinctrl/spear/Kconfig"
 source "drivers/pinctrl/stm32/Kconfig"
 source "drivers/pinctrl/sunxi/Kconfig"
 source "drivers/pinctrl/tegra/Kconfig"
+source "drivers/pinctrl/ti/Kconfig"
 source "drivers/pinctrl/uniphier/Kconfig"
 source "drivers/pinctrl/vt8500/Kconfig"
 source "drivers/pinctrl/mediatek/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_PINCTRL_SH_PFC)	+= sh-pfc/
 obj-$(CONFIG_PINCTRL_SPEAR)	+= spear/
 obj-$(CONFIG_PINCTRL_STM32)	+= stm32/
 obj-$(CONFIG_PINCTRL_SUNXI)	+= sunxi/
+obj-y				+= ti/
 obj-$(CONFIG_PINCTRL_UNIPHIER)	+= uniphier/
 obj-$(CONFIG_ARCH_VT8500)	+= vt8500/
 obj-$(CONFIG_PINCTRL_MTK)	+= mediatek/
diff --git a/drivers/pinctrl/ti/Kconfig b/drivers/pinctrl/ti/Kconfig
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/Kconfig
@@ -0,0 +1,10 @@
+config PINCTRL_TI_IODELAY
+	tristate "TI IODelay Module pinconf driver"
+	depends on OF
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GENERIC_PINCONF
+	select REGMAP_MMIO
+	help
+	  Say Y here to support Texas Instruments' IO delay pinconf driver.
+	  IO delay module is used for the DRA7 SoC family.
diff --git a/drivers/pinctrl/ti/Makefile b/drivers/pinctrl/ti/Makefile
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_PINCTRL_TI_IODELAY)	+= pinctrl-ti-iodelay.o
diff --git a/drivers/pinctrl/ti/pinctrl-ti-iodelay.c b/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
@@ -0,0 +1,945 @@
+/*
+ * Support for configuration of IO Delay module found on Texas Instruments SoCs
+ * such as DRA7
+ *
+ * Copyright (C) 2015 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "../core.h"
+#include "../devicetree.h"
+
+#define DRIVER_NAME	"ti-iodelay"
+
+/**
+ * struct ti_iodelay_reg_data - Describes the registers for the iodelay instance
+ * @signature_mask: CONFIG_REG mask for the signature bits (see TRM)
+ * @signature_value: CONFIG_REG signature value to be written (see TRM)
+ * @lock_mask: CONFIG_REG mask for the lock bits (see TRM)
+ * @lock_val: CONFIG_REG lock value for the lock bits (see TRM)
+ * @unlock_val:CONFIG_REG unlock value for the lock bits (see TRM)
+ * @binary_data_coarse_mask: CONFIG_REG coarse mask (see TRM)
+ * @binary_data_fine_mask: CONFIG_REG fine mask (see TRM)
+ * @reg_refclk_offset: Refclk register offset
+ * @refclk_period_mask: Refclk mask
+ * @reg_coarse_offset: Coarse register configuration offset
+ * @coarse_delay_count_mask: Coarse delay count mask
+ * @coarse_ref_count_mask: Coarse ref count mask
+ * @reg_fine_offset: Fine register configuration offset
+ * @fine_delay_count_mask: Fine delay count mask
+ * @fine_ref_count_mask: Fine ref count mask
+ * @reg_global_lock_offset: Global iodelay module lock register offset
+ * @global_lock_mask: Lock mask
+ * @global_unlock_val: Unlock value
+ * @global_lock_val: Lock value
+ * @reg_start_offset: Offset to iodelay registers after the CONFIG_REG_0 to 8
+ * @reg_nr_per_pin: Number of iodelay registers for each pin
+ * @regmap_config: Regmap configuration for the IODelay region
+ */
+struct ti_iodelay_reg_data {
+	u32 signature_mask;
+	u32 signature_value;
+	u32 lock_mask;
+	u32 lock_val;
+	u32 unlock_val;
+	u32 binary_data_coarse_mask;
+	u32 binary_data_fine_mask;
+
+	u32 reg_refclk_offset;
+	u32 refclk_period_mask;
+
+	u32 reg_coarse_offset;
+	u32 coarse_delay_count_mask;
+	u32 coarse_ref_count_mask;
+
+	u32 reg_fine_offset;
+	u32 fine_delay_count_mask;
+	u32 fine_ref_count_mask;
+
+	u32 reg_global_lock_offset;
+	u32 global_lock_mask;
+	u32 global_unlock_val;
+	u32 global_lock_val;
+
+	u32 reg_start_offset;
+	u32 reg_nr_per_pin;
+
+	struct regmap_config *regmap_config;
+};
+
+/**
+ * struct ti_iodelay_reg_values - Computed io_reg configuration values (see TRM)
+ * @coarse_ref_count: Coarse reference count
+ * @coarse_delay_count: Coarse delay count
+ * @fine_ref_count: Fine reference count
+ * @fine_delay_count: Fine Delay count
+ * @ref_clk_period: Reference Clock period
+ * @cdpe: Coarse delay parameter
+ * @fdpe: Fine delay parameter
+ */
+struct ti_iodelay_reg_values {
+	u16 coarse_ref_count;
+	u16 coarse_delay_count;
+
+	u16 fine_ref_count;
+	u16 fine_delay_count;
+
+	u16 ref_clk_period;
+
+	u32 cdpe;
+	u32 fdpe;
+};
+
+/**
+ * struct ti_iodelay_cfg - Description of each configuration parameters
+ * @offset: Configuration register offset
+ * @a_delay: Agnostic Delay (in ps)
+ * @g_delay: Gnostic Delay (in ps)
+ */
+struct ti_iodelay_cfg {
+	u16 offset;
+	u16 a_delay;
+	u16 g_delay;
+};
+
+/**
+ * struct ti_iodelay_pingroup - Structure that describes one group
+ * @name: Name of the group
+ * @map: pinctrl map allocated for the group
+ * @cfg: configuration array for the pin (from dt)
+ * @ncfg: number of configuration values allocated
+ * @config: pinconf "Config" - currently a dummy value
+ */
+struct ti_iodelay_pingroup {
+	struct ti_iodelay_cfg *cfg;
+	int ncfg;
+	unsigned long config;
+};
+
+/**
+ * struct ti_iodelay_device - Represents information for a iodelay instance
+ * @dev: Device pointer
+ * @phys_base: Physical address base of the iodelay device
+ * @reg_base: Virtual address base of the iodelay device
+ * @regmap: Regmap for this iodelay instance
+ * @pctl: Pinctrl device
+ * @desc: pinctrl descriptor for pctl
+ * @pa: pinctrl pin wise description
+ * @names: names of the pins
+ * @reg_data: Register definition data for the IODelay instance
+ * @reg_init_conf_values: Initial configuration values.
+ */
+struct ti_iodelay_device {
+	struct device *dev;
+	unsigned long phys_base;
+	void __iomem *reg_base;
+	struct regmap *regmap;
+
+	struct pinctrl_dev *pctl;
+	struct pinctrl_desc desc;
+	struct pinctrl_pin_desc *pa;
+
+	const struct ti_iodelay_reg_data *reg_data;
+	struct ti_iodelay_reg_values reg_init_conf_values;
+};
+
+/**
+ * ti_iodelay_extract() - extract bits for a field
+ * @val: Register value
+ * @mask: Mask
+ *
+ * Return: extracted value which is appropriately shifted
+ */
+static inline u32 ti_iodelay_extract(u32 val, u32 mask)
+{
+	return (val & mask) >> __ffs(mask);
+}
+
+/**
+ * ti_iodelay_compute_dpe() - Compute equation for delay parameter
+ * @period: Period to use
+ * @ref: Reference Count
+ * @delay: Delay count
+ * @delay_m: Delay multiplier
+ *
+ * Return: Computed delay parameter
+ */
+static inline u32 ti_iodelay_compute_dpe(u16 period, u16 ref, u16 delay,
+					 u16 delay_m)
+{
+	u64 m, d;
+
+	/* Handle overflow conditions */
+	m = 10 * (u64)period * (u64)ref;
+	d = 2 * (u64)delay * (u64)delay_m;
+
+	/* Truncate result back to 32 bits */
+	return div64_u64(m, d);
+}
+
+/**
+ * ti_iodelay_pinconf_set() - Configure the pin configuration
+ * @iod: iodelay device
+ * @val: Configuration value
+ *
+ * Update the configuration register as per TRM and lockup once done.
+ * *IMPORTANT NOTE* SoC TRM does recommend doing iodelay programmation only
+ * while in Isolation. But, then, isolation also implies that every pin
+ * on the SoC (including DDR) will be isolated out. The only benefit being
+ * a glitchless configuration, However, the intent of this driver is purely
+ * to support a "glitchy" configuration where applicable.
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_pinconf_set(struct ti_iodelay_device *iod,
+				  struct ti_iodelay_cfg *cfg)
+{
+	const struct ti_iodelay_reg_data *reg = iod->reg_data;
+	struct ti_iodelay_reg_values *ival = &iod->reg_init_conf_values;
+	struct device *dev = iod->dev;
+	u32 g_delay_coarse, g_delay_fine;
+	u32 a_delay_coarse, a_delay_fine;
+	u32 c_elements, f_elements;
+	u32 total_delay;
+	u32 reg_mask, reg_val, tmp_val;
+	int r;
+
+	/* NOTE: Truncation is expected in all division below */
+	g_delay_coarse = cfg->g_delay / 920;
+	g_delay_fine = ((cfg->g_delay % 920) * 10) / 60;
+
+	a_delay_coarse = cfg->a_delay / ival->cdpe;
+	a_delay_fine = ((cfg->a_delay % ival->cdpe) * 10) / ival->fdpe;
+
+	c_elements = g_delay_coarse + a_delay_coarse;
+	f_elements = (g_delay_fine + a_delay_fine) / 10;
+
+	if (f_elements > 22) {
+		total_delay = c_elements * ival->cdpe + f_elements * ival->fdpe;
+		c_elements = total_delay / ival->cdpe;
+		f_elements = (total_delay % ival->cdpe) / ival->fdpe;
+	}
+
+	reg_mask = reg->signature_mask;
+	reg_val = reg->signature_value << __ffs(reg->signature_mask);
+
+	reg_mask |= reg->binary_data_coarse_mask;
+	tmp_val = c_elements << __ffs(reg->binary_data_coarse_mask);
+	if (tmp_val & ~reg->binary_data_coarse_mask) {
+		dev_err(dev, "Masking overflow of coarse elements %08x\n",
+			tmp_val);
+		tmp_val &= reg->binary_data_coarse_mask;
+	}
+	reg_val |= tmp_val;
+
+	reg_mask |= reg->binary_data_fine_mask;
+	tmp_val = f_elements << __ffs(reg->binary_data_fine_mask);
+	if (tmp_val & ~reg->binary_data_fine_mask) {
+		dev_err(dev, "Masking overflow of fine elements %08x\n",
+			tmp_val);
+		tmp_val &= reg->binary_data_fine_mask;
+	}
+	reg_val |= tmp_val;
+
+	/*
+	 * NOTE: we leave the iodelay values unlocked - this is to work around
+	 * situations such as those found with mmc mode change.
+	 * However, this leaves open any unwarranted changes to padconf register
+	 * impacting iodelay configuration. Use with care!
+	 */
+	reg_mask |= reg->lock_mask;
+	reg_val |= reg->unlock_val << __ffs(reg->lock_mask);
+	r = regmap_update_bits(iod->regmap, cfg->offset, reg_mask, reg_val);
+
+	dev_info(dev, "Set reg 0x%x Delay(a: %d g: %d), Elements(C=%d F=%d)0x%x\n",
+		 cfg->offset, cfg->a_delay, cfg->g_delay, c_elements,
+		 f_elements, reg_val);
+
+	return r;
+}
+
+/**
+ * ti_iodelay_pinconf_init_dev() - Initialize IODelay device
+ * @iod: iodelay device
+ *
+ * Unlocks the iodelay region, computes the common parameters
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_pinconf_init_dev(struct ti_iodelay_device *iod)
+{
+	const struct ti_iodelay_reg_data *reg = iod->reg_data;
+	struct device *dev = iod->dev;
+	struct ti_iodelay_reg_values *ival = &iod->reg_init_conf_values;
+	u32 val;
+	int r;
+
+	/* unlock the iodelay region */
+	r = regmap_update_bits(iod->regmap, reg->reg_global_lock_offset,
+			       reg->global_lock_mask, reg->global_unlock_val);
+	if (r)
+		return r;
+
+	/* Read up Recalibration sequence done by bootloader */
+	r = regmap_read(iod->regmap, reg->reg_refclk_offset, &val);
+	if (r)
+		return r;
+	ival->ref_clk_period = ti_iodelay_extract(val, reg->refclk_period_mask);
+	dev_dbg(dev, "refclk_period=0x%04x\n", ival->ref_clk_period);
+
+	r = regmap_read(iod->regmap, reg->reg_coarse_offset, &val);
+	if (r)
+		return r;
+	ival->coarse_ref_count =
+	    ti_iodelay_extract(val, reg->coarse_ref_count_mask);
+	ival->coarse_delay_count =
+	    ti_iodelay_extract(val, reg->coarse_delay_count_mask);
+	if (!ival->coarse_delay_count) {
+		dev_err(dev, "Invalid Coarse delay count (0) (reg=0x%08x)\n",
+			val);
+		return -EINVAL;
+	}
+	ival->cdpe = ti_iodelay_compute_dpe(ival->ref_clk_period,
+					    ival->coarse_ref_count,
+					    ival->coarse_delay_count, 88);
+	if (!ival->cdpe) {
+		dev_err(dev, "Invalid cdpe computed params = %d %d %d\n",
+			ival->ref_clk_period, ival->coarse_ref_count,
+			ival->coarse_delay_count);
+		return -EINVAL;
+	}
+	dev_dbg(iod->dev, "coarse: ref=0x%04x delay=0x%04x cdpe=0x%08x\n",
+		ival->coarse_ref_count, ival->coarse_delay_count, ival->cdpe);
+
+	r = regmap_read(iod->regmap, reg->reg_fine_offset, &val);
+	if (r)
+		return r;
+	ival->fine_ref_count =
+	    ti_iodelay_extract(val, reg->fine_ref_count_mask);
+	ival->fine_delay_count =
+	    ti_iodelay_extract(val, reg->fine_delay_count_mask);
+	if (!ival->fine_delay_count) {
+		dev_err(dev, "Invalid Fine delay count (0) (reg=0x%08x)\n",
+			val);
+		return -EINVAL;
+	}
+	ival->fdpe = ti_iodelay_compute_dpe(ival->ref_clk_period,
+					    ival->fine_ref_count,
+					    ival->fine_delay_count, 264);
+	if (!ival->fdpe) {
+		dev_err(dev, "Invalid fdpe(0) computed params = %d %d %d\n",
+			ival->ref_clk_period, ival->fine_ref_count,
+			ival->fine_delay_count);
+		return -EINVAL;
+	}
+	dev_dbg(iod->dev, "fine: ref=0x%04x delay=0x%04x fdpe=0x%08x\n",
+		ival->fine_ref_count, ival->fine_delay_count, ival->fdpe);
+
+	return 0;
+}
+
+/**
+ * ti_iodelay_pinconf_deinit_dev() - deinit the iodelay device
+ * @iod:	IODelay device
+ *
+ * Deinitialize the IODelay device (basically just lock the region back up.
+ */
+static void ti_iodelay_pinconf_deinit_dev(struct ti_iodelay_device *iod)
+{
+	const struct ti_iodelay_reg_data *reg = iod->reg_data;
+
+	/* lock the iodelay region back again */
+	regmap_update_bits(iod->regmap, reg->reg_global_lock_offset,
+			   reg->global_lock_mask, reg->global_lock_val);
+}
+
+/**
+ * ti_iodelay_get_pingroup() - Find the group mapped by a group selector
+ * @iod: iodelay device
+ * @selector: Group Selector
+ *
+ * Return: Corresponding group representing group selector
+ */
+static struct ti_iodelay_pingroup *
+ti_iodelay_get_pingroup(struct ti_iodelay_device *iod, unsigned int selector)
+{
+	struct group_desc *g;
+
+	g = pinctrl_generic_get_group(iod->pctl, selector);
+	if (!g) {
+		dev_err(iod->dev, "%s could not find pingroup %i\n", __func__,
+			selector);
+
+		return NULL;
+	}
+
+	return g->data;
+}
+
+/**
+ * ti_iodelay_pin_to_offset() - get pin register offset based on the pin index
+ * @iod: iodelay driver instance
+ * @selector: Pin index
+ */
+static unsigned int ti_iodelay_pin_to_offset(struct ti_iodelay_device *iod,
+					     unsigned int selector)
+{
+	const struct ti_iodelay_reg_data *r = iod->reg_data;
+	unsigned int offset;
+
+	offset = selector * r->regmap_config->reg_stride;
+	offset *= r->reg_nr_per_pin;
+	offset += r->reg_start_offset;
+
+	return offset;
+}
+
+/**
+ * ti_iodelay_offset_to_pin() - get a pin index based on the register offset
+ * @iod: iodelay driver instance
+ * @offset: register offset from the base
+ */
+static int ti_iodelay_offset_to_pin(struct ti_iodelay_device *iod,
+				    unsigned int offset)
+{
+	const struct ti_iodelay_reg_data *r = iod->reg_data;
+	unsigned int index;
+
+	if (offset > r->regmap_config->max_register) {
+		dev_err(iod->dev, "mux offset out of range: 0x%x (0x%x)\n",
+			offset, r->regmap_config->max_register);
+		return -EINVAL;
+	}
+
+	index = (offset - r->reg_start_offset) / r->regmap_config->reg_stride;
+	index /= r->reg_nr_per_pin;
+
+	return index;
+}
+
+/**
+ *
+ * @pctldev: Pin controller driver
+ * @np: Device node
+ * @pinctrl_spec: Parsed arguments from device tree
+ * @pins: Array of pins in the pin group
+ * @pin_index: Pin index in the pin array
+ * @data: Pin controller driver specific data
+ *
+ */
+static int ti_iodelay_node_iterator(struct pinctrl_dev *pctldev,
+				    struct device_node *np,
+				    const struct of_phandle_args *pinctrl_spec,
+				    int *pins, int pin_index, void *data)
+{
+	struct ti_iodelay_device *iod;
+	struct ti_iodelay_cfg *cfg = data;
+	const struct ti_iodelay_reg_data *r;
+	struct pinctrl_pin_desc *pd;
+	int pin;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	if (!iod)
+		return -EINVAL;
+
+	r = iod->reg_data;
+
+	if (pinctrl_spec->args_count < r->reg_nr_per_pin) {
+		dev_err(iod->dev, "invalid args_count for spec: %i\n",
+			pinctrl_spec->args_count);
+
+		return -EINVAL;
+	}
+
+	/* Index plus two value cells */
+	cfg[pin_index].offset = pinctrl_spec->args[0];
+	cfg[pin_index].a_delay = pinctrl_spec->args[1] & 0xffff;
+	cfg[pin_index].g_delay = pinctrl_spec->args[2] & 0xffff;
+
+	pin = ti_iodelay_offset_to_pin(iod, cfg[pin_index].offset);
+	if (pin < 0) {
+		dev_err(iod->dev, "could not add functions for %s %ux\n",
+			np->name, cfg[pin_index].offset);
+		return -ENODEV;
+	}
+	pins[pin_index] = pin;
+
+	pd = &iod->pa[pin];
+	pd->drv_data = &cfg[pin_index];
+
+	dev_dbg(iod->dev, "%s offset=%x a_delay = %d g_delay = %d\n",
+		np->name, cfg[pin_index].offset, cfg[pin_index].a_delay,
+		cfg[pin_index].g_delay);
+
+	return 0;
+}
+
+/**
+ * ti_iodelay_dt_node_to_map() - Map a device tree node to appropriate group
+ * @pctldev: pinctrl device representing IODelay device
+ * @np: Node Pointer (device tree)
+ * @map: Pinctrl Map returned back to pinctrl framework
+ * @num_maps: Number of maps (1)
+ *
+ * Maps the device tree description into a group of configuration parameters
+ * for iodelay block entry.
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_dt_node_to_map(struct pinctrl_dev *pctldev,
+				     struct device_node *np,
+				     struct pinctrl_map **map,
+				     unsigned int *num_maps)
+{
+	struct ti_iodelay_device *iod;
+	struct ti_iodelay_cfg *cfg;
+	struct ti_iodelay_pingroup *g;
+	const char *name = "pinctrl-pin-array";
+	int rows, *pins, error = -EINVAL, i;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	if (!iod)
+		return -EINVAL;
+
+	rows = pinctrl_count_index_with_args(np, name);
+	if (rows == -EINVAL)
+		return rows;
+
+	*map = devm_kzalloc(iod->dev, sizeof(**map), GFP_KERNEL);
+	if (!*map)
+		return -ENOMEM;
+	*num_maps = 0;
+
+	g = devm_kzalloc(iod->dev, sizeof(*g), GFP_KERNEL);
+	if (!g) {
+		error = -ENOMEM;
+		goto free_map;
+	}
+
+	pins = devm_kzalloc(iod->dev, sizeof(*pins) * rows, GFP_KERNEL);
+	if (!pins)
+		goto free_group;
+
+	cfg = devm_kzalloc(iod->dev, sizeof(*cfg) * rows, GFP_KERNEL);
+	if (!cfg) {
+		error = -ENOMEM;
+		goto free_pins;
+	}
+
+	for (i = 0; i < rows; i++) {
+		struct of_phandle_args pinctrl_spec;
+
+		error = pinctrl_parse_index_with_args(np, name, i,
+						      &pinctrl_spec);
+		if (error)
+			goto free_data;
+
+		error = ti_iodelay_node_iterator(pctldev, np, &pinctrl_spec,
+						 pins, i, cfg);
+		if (error)
+			goto free_data;
+	}
+
+	g->cfg = cfg;
+	g->ncfg = i;
+	g->config = PIN_CONFIG_END;
+
+	error = pinctrl_generic_add_group(iod->pctl, np->name, pins, i, g);
+	if (error < 0)
+		goto free_data;
+
+	(*map)->type = PIN_MAP_TYPE_CONFIGS_GROUP;
+	(*map)->data.configs.group_or_pin = np->name;
+	(*map)->data.configs.configs = &g->config;
+	(*map)->data.configs.num_configs = 1;
+	*num_maps = 1;
+
+	return 0;
+
+free_data:
+	devm_kfree(iod->dev, cfg);
+free_pins:
+	devm_kfree(iod->dev, pins);
+free_group:
+	devm_kfree(iod->dev, g);
+free_map:
+	devm_kfree(iod->dev, *map);
+
+	return error;
+}
+
+/**
+ * ti_iodelay_pinconf_group_get() - Get the group configuration
+ * @pctldev: pinctrl device representing IODelay device
+ * @selector: Group selector
+ * @config: Configuration returned
+ *
+ * Return: The configuration if the group is valid, else returns -EINVAL
+ */
+static int ti_iodelay_pinconf_group_get(struct pinctrl_dev *pctldev,
+					unsigned int selector,
+					unsigned long *config)
+{
+	struct ti_iodelay_device *iod;
+	struct device *dev;
+	struct ti_iodelay_pingroup *group;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	dev = iod->dev;
+	group = ti_iodelay_get_pingroup(iod, selector);
+
+	if (!group)
+		return -EINVAL;
+
+	*config = group->config;
+	return 0;
+}
+
+/**
+ * ti_iodelay_pinconf_group_set() - Configure the groups of pins
+ * @pctldev: pinctrl device representing IODelay device
+ * @selector: Group selector
+ * @configs: Configurations
+ * @num_configs: Number of configurations
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_pinconf_group_set(struct pinctrl_dev *pctldev,
+					unsigned int selector,
+					unsigned long *configs,
+					unsigned int num_configs)
+{
+	struct ti_iodelay_device *iod;
+	struct device *dev;
+	struct ti_iodelay_pingroup *group;
+	int i;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	dev = iod->dev;
+	group = ti_iodelay_get_pingroup(iod, selector);
+
+	if (num_configs != 1) {
+		dev_err(dev, "Unsupported number of configurations %d\n",
+			num_configs);
+		return -EINVAL;
+	}
+
+	if (*configs != PIN_CONFIG_END) {
+		dev_err(dev, "Unsupported configuration\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < group->ncfg; i++) {
+		if (ti_iodelay_pinconf_set(iod, &group->cfg[i]))
+			return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void ti_iodelay_pin_dbg_show(struct pinctrl_dev *pctldev,
+				    struct seq_file *s,
+				    unsigned int pin)
+{
+	struct ti_iodelay_device *iod;
+	struct pinctrl_pin_desc *pd;
+	struct ti_iodelay_cfg *cfg;
+	const struct ti_iodelay_reg_data *r;
+	unsigned long offset;
+	u32 in, oen, out;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	r = iod->reg_data;
+
+	offset = ti_iodelay_pin_to_offset(iod, pin);
+	if (pin < 0) {
+		dev_err(iod->dev, "invalid pin offset for pin%i\n", pin);
+
+		return;
+	}
+
+	pd = &iod->pa[pin];
+	cfg = pd->drv_data;
+
+	regmap_read(iod->regmap, offset, &in);
+	regmap_read(iod->regmap, offset + r->regmap_config->reg_stride, &oen);
+	regmap_read(iod->regmap, offset + r->regmap_config->reg_stride * 2,
+		    &out);
+
+	seq_printf(s, "%lx a: %i g: %i (%08x %08x %08x) %s ",
+		   iod->phys_base + offset,
+		   cfg ? cfg->a_delay : -1,
+		   cfg ? cfg->g_delay : -1,
+		   in, oen, out, DRIVER_NAME);
+}
+
+/**
+ * ti_iodelay_pinconf_group_dbg_show() - show the group information
+ * @pctldev: Show the group information
+ * @s: Sequence file
+ * @selector: Group selector
+ *
+ * Provide the configuration information of the selected group
+ */
+static void ti_iodelay_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
+					      struct seq_file *s,
+					      unsigned int selector)
+{
+	struct ti_iodelay_device *iod;
+	struct device *dev;
+	struct ti_iodelay_pingroup *group;
+	int i;
+
+	iod = pinctrl_dev_get_drvdata(pctldev);
+	dev = iod->dev;
+	group = ti_iodelay_get_pingroup(iod, selector);
+	if (!group)
+		return;
+
+	for (i = 0; i < group->ncfg; i++) {
+		struct ti_iodelay_cfg *cfg;
+		u32 reg = 0;
+
+		cfg = &group->cfg[i];
+		regmap_read(iod->regmap, cfg->offset, &reg),
+			seq_printf(s, "\n\t0x%08x = 0x%08x (%3d, %3d)",
+				   cfg->offset, reg, cfg->a_delay,
+				   cfg->g_delay);
+	}
+}
+#endif
+
+static struct pinctrl_ops ti_iodelay_pinctrl_ops = {
+	.get_groups_count = pinctrl_generic_get_group_count,
+	.get_group_name = pinctrl_generic_get_group_name,
+	.get_group_pins = pinctrl_generic_get_group_pins,
+	.pin_dbg_show = ti_iodelay_pin_dbg_show,
+	.dt_node_to_map = ti_iodelay_dt_node_to_map,
+};
+
+static struct pinconf_ops ti_iodelay_pinctrl_pinconf_ops = {
+	.pin_config_group_get = ti_iodelay_pinconf_group_get,
+	.pin_config_group_set = ti_iodelay_pinconf_group_set,
+#ifdef CONFIG_DEBUG_FS
+	.pin_config_group_dbg_show = ti_iodelay_pinconf_group_dbg_show,
+#endif
+};
+
+/**
+ * ti_iodelay_alloc_pins() - Allocate structures needed for pins for iodelay
+ * @dev: Device pointer
+ * @iod: iodelay device
+ * @base_phy: Base Physical Address
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_alloc_pins(struct device *dev,
+				 struct ti_iodelay_device *iod, u32 base_phy)
+{
+	const struct ti_iodelay_reg_data *r = iod->reg_data;
+	struct pinctrl_pin_desc *pin;
+	u32 phy_reg;
+	int nr_pins, i;
+
+	nr_pins = ti_iodelay_offset_to_pin(iod, r->regmap_config->max_register);
+	dev_dbg(dev, "Allocating %i pins\n", nr_pins);
+
+	iod->pa = devm_kzalloc(dev, sizeof(*iod->pa) * nr_pins, GFP_KERNEL);
+	if (!iod->pa)
+		return -ENOMEM;
+
+	iod->desc.pins = iod->pa;
+	iod->desc.npins = nr_pins;
+
+	phy_reg = r->reg_start_offset + base_phy;
+
+	for (i = 0; i < nr_pins; i++, phy_reg += 4) {
+		pin = &iod->pa[i];
+		pin->number = i;
+	}
+
+	return 0;
+}
+
+static struct regmap_config dra7_iodelay_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.max_register = 0xd1c,
+};
+
+static struct ti_iodelay_reg_data dra7_iodelay_data = {
+	.signature_mask = 0x0003f000,
+	.signature_value = 0x29,
+	.lock_mask = 0x00000400,
+	.lock_val = 1,
+	.unlock_val = 0,
+	.binary_data_coarse_mask = 0x000003e0,
+	.binary_data_fine_mask = 0x0000001f,
+
+	.reg_refclk_offset = 0x14,
+	.refclk_period_mask = 0xffff,
+
+	.reg_coarse_offset = 0x18,
+	.coarse_delay_count_mask = 0xffff0000,
+	.coarse_ref_count_mask = 0x0000ffff,
+
+	.reg_fine_offset = 0x1C,
+	.fine_delay_count_mask = 0xffff0000,
+	.fine_ref_count_mask = 0x0000ffff,
+
+	.reg_global_lock_offset = 0x2c,
+	.global_lock_mask = 0x0000ffff,
+	.global_unlock_val = 0x0000aaaa,
+	.global_lock_val = 0x0000aaab,
+
+	.reg_start_offset = 0x30,
+	.reg_nr_per_pin = 3,
+	.regmap_config = &dra7_iodelay_regmap_config,
+};
+
+static const struct of_device_id ti_iodelay_of_match[] = {
+	{.compatible = "ti,dra7-iodelay", .data = &dra7_iodelay_data},
+	{ /* Hopefully no more.. */ },
+};
+MODULE_DEVICE_TABLE(of, ti_iodelay_of_match);
+
+/**
+ * ti_iodelay_probe() - Standard probe
+ * @pdev: platform device
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = of_node_get(dev->of_node);
+	const struct of_device_id *match;
+	struct resource *res;
+	struct ti_iodelay_device *iod;
+	int ret = 0;
+
+	if (!np) {
+		ret = -EINVAL;
+		dev_err(dev, "No OF node\n");
+		goto exit_out;
+	}
+
+	match = of_match_device(ti_iodelay_of_match, dev);
+	if (!match) {
+		ret = -EINVAL;
+		dev_err(dev, "No DATA match\n");
+		goto exit_out;
+	}
+
+	iod = devm_kzalloc(dev, sizeof(*iod), GFP_KERNEL);
+	if (!iod) {
+		ret = -ENOMEM;
+		goto exit_out;
+	}
+	iod->dev = dev;
+	iod->reg_data = match->data;
+
+	/* So far We can assume there is only 1 bank of registers */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Missing MEM resource\n");
+		ret = -ENODEV;
+		goto exit_out;
+	}
+
+	iod->phys_base = res->start;
+	iod->reg_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(iod->reg_base)) {
+		ret = PTR_ERR(iod->reg_base);
+		goto exit_out;
+	}
+
+	iod->regmap = devm_regmap_init_mmio(dev, iod->reg_base,
+					    iod->reg_data->regmap_config);
+	if (IS_ERR(iod->regmap)) {
+		dev_err(dev, "Regmap MMIO init failed.\n");
+		ret = PTR_ERR(iod->regmap);
+		goto exit_out;
+	}
+
+	if (ti_iodelay_pinconf_init_dev(iod))
+		goto exit_out;
+
+	ret = ti_iodelay_alloc_pins(dev, iod, res->start);
+	if (ret)
+		goto exit_out;
+
+	iod->desc.pctlops = &ti_iodelay_pinctrl_ops;
+	/* no pinmux ops - we are pinconf */
+	iod->desc.confops = &ti_iodelay_pinctrl_pinconf_ops;
+	iod->desc.name = dev_name(dev);
+	iod->desc.owner = THIS_MODULE;
+
+	iod->pctl = pinctrl_register(&iod->desc, dev, iod);
+	if (!iod->pctl) {
+		dev_err(dev, "Failed to register pinctrl\n");
+		ret = -ENODEV;
+		goto exit_out;
+	}
+
+	platform_set_drvdata(pdev, iod);
+
+exit_out:
+	of_node_put(np);
+	return ret;
+}
+
+/**
+ * ti_iodelay_remove() - standard remove
+ * @pdev: platform device
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_remove(struct platform_device *pdev)
+{
+	struct ti_iodelay_device *iod = platform_get_drvdata(pdev);
+
+	if (!iod)
+		return 0;
+
+	if (iod->pctl)
+		pinctrl_unregister(iod->pctl);
+
+	ti_iodelay_pinconf_deinit_dev(iod);
+
+	/* Expect other allocations to be freed by devm */
+
+	return 0;
+}
+
+static struct platform_driver ti_iodelay_driver = {
+	.probe = ti_iodelay_probe,
+	.remove = ti_iodelay_remove,
+	.driver = {
+		   .owner = THIS_MODULE,
+		   .name = DRIVER_NAME,
+		   .of_match_table = ti_iodelay_of_match,
+	},
+};
+module_platform_driver(ti_iodelay_driver);
+
+MODULE_AUTHOR("Texas Instruments, Inc.");
+MODULE_DESCRIPTION("Pinconf driver for TI's IO Delay module");
+MODULE_LICENSE("GPL v2");
