deleted file mode 100644
@@ -1,187 +0,0 @@
-Qualcomm PMIC Multi-Purpose Pin (MPP) block
-
-This binding describes the MPP block(s) found in the 8xxx series
-of PMIC's from Qualcomm.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: Should contain one of:
- "qcom,pm8018-mpp",
- "qcom,pm8019-mpp",
- "qcom,pm8038-mpp",
- "qcom,pm8058-mpp",
- "qcom,pm8821-mpp",
- "qcom,pm8841-mpp",
- "qcom,pm8916-mpp",
- "qcom,pm8917-mpp",
- "qcom,pm8921-mpp",
- "qcom,pm8941-mpp",
- "qcom,pm8950-mpp",
- "qcom,pmi8950-mpp",
- "qcom,pm8994-mpp",
- "qcom,pma8084-mpp",
- "qcom,pmi8994-mpp",
-
- And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp"
- if the device is on an spmi bus or an ssbi bus respectively.
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: Register base of the MPP block and length.
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: Must contain an array of encoded interrupt specifiers for
- each available MPP
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: Mark the device node as a GPIO controller
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: Must be 2;
- the first cell will be used to define MPP number and the
- second denotes the flags for this MPP
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin or a list of pins. This configuration can include the
-mux function to select on those pin(s), and various pin configuration
-parameters, as listed below.
-
-SUBNODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of MPP pins affected by the properties specified in
- this subnode. Valid pins are:
- mpp1-mpp4 for pm8841
- mpp1-mpp4 for pm8916
- mpp1-mpp8 for pm8941
- mpp1-mpp4 for pm8950
- mpp1-mpp4 for pmi8950
- mpp1-mpp4 for pma8084
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Valid values are:
- "digital",
- "analog",
- "sink"
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-up:
- Usage: optional
- Value type: <u32>
- Definition: The specified pins should be configured as pull up.
- Valid values are 600, 10000 and 30000 in bidirectional mode
- only, i.e. when operating in qcom,analog-mode and input and
- outputs are enabled. The hardware ignores the configuration
- when operating in other modes.
-
-- bias-high-impedance:
- Usage: optional
- Value type: <none>
- Definition: The specified pins will put in high-Z mode and disabled.
-
-- input-enable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are put in input mode, i.e. their input
- buffer is enabled
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
-
-- power-source:
- Usage: optional
- Value type: <u32>
- Definition: Selects the power source for the specified pins. Valid power
- sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-
-- qcom,analog-level:
- Usage: optional
- Value type: <u32>
- Definition: Selects the source for analog output. Valued values are
- defined in <dt-binding/pinctrl/qcom,pmic-mpp.h>
- PMIC_MPP_AOUT_LVL_*
-
-- qcom,dtest:
- Usage: optional
- Value type: <u32>
- Definition: Selects which dtest rail to be routed in the various functions.
- Valid values are 1-4
-
-- qcom,amux-route:
- Usage: optional
- Value type: <u32>
- Definition: Selects the source for analog input. Valid values are
- defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
- PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
-- qcom,paired:
- Usage: optional
- Value type: <none>
- Definition: Indicates that the pin should be operating in paired mode.
-
-Example:
-
- mpps@a000 {
- compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
- reg = <0xa000>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pm8841_default>;
-
- pm8841_default: default {
- gpio {
- pins = "mpp1", "mpp2", "mpp3", "mpp4";
- function = "digital";
- input-enable;
- power-source = <PM8841_MPP_S3>;
- };
- };
- };
new file mode 100644
@@ -0,0 +1,178 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,pmic-mpp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PMIC Multi-Purpose Pin (MPP) block
+
+maintainers:
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description:
+ This binding describes the MPP block(s) found in the 8xxx series of
+ PMIC's from Qualcomm.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,pm8018-mpp
+ - qcom,pm8019-mpp
+ - qcom,pm8038-mpp
+ - qcom,pm8058-mpp
+ - qcom,pm8821-mpp
+ - qcom,pm8841-mpp
+ - qcom,pm8916-mpp
+ - qcom,pm8917-mpp
+ - qcom,pm8921-mpp
+ - qcom,pm8941-mpp
+ - qcom,pm8950-mpp
+ - qcom,pmi8950-mpp
+ - qcom,pm8994-mpp
+ - qcom,pma8084-mpp
+ - qcom,pmi8994-mpp
+
+ - enum:
+ - qcom,spmi-mpp
+ - qcom,ssbi-mpp
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 12
+ description:
+ Must contain an array of encoded interrupt specifiers for
+ each available MPP
+
+ gpio-controller: true
+
+ gpio-ranges:
+ maxItems: 1
+
+ '#gpio-cells':
+ const: 2
+ description:
+ The first cell will be used to define gpio number and the
+ second denotes the flags for this gpio
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+ - interrupt-controller
+
+patternProperties:
+ '-state$':
+ oneOf:
+ - $ref: "#/$defs/qcom-pmic-mpp-state"
+ - patternProperties:
+ ".*":
+ $ref: "#/$defs/qcom-pmic-mpp-state"
+
+$defs:
+ qcom-pmic-mpp-state:
+ type: object
+ allOf:
+ - $ref: "pinmux-node.yaml"
+ - $ref: "pincfg-node.yaml"
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in
+ this subnode. Valid pins are
+ - mpp1-mpp4 for pm8841
+ - mpp1-mpp4 for pm8916
+ - mpp1-mpp8 for pm8941
+ - mpp1-mpp4 for pm8950
+ - mpp1-mpp4 for pmi8950
+ - mpp1-mpp4 for pma8084
+
+ items:
+ pattern: "^mpp([0-9]+)$"
+
+ function:
+ items:
+ - enum:
+ - digital
+ - analog
+ - sink
+
+ bias-disable: true
+ bias-pull-up: true
+ bias-high-impedance: true
+ input-enable: true
+ output-high: true
+ output-low: true
+ power-source: true
+
+ qcom,analog-level:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selects the source for analog output. Valued values are defined in
+ <dt-binding/pinctrl/qcom,pmic-mpp.h> PMIC_MPP_AOUT_LVL_*
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ qcom,atest:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selects ATEST rail to route to GPIO when it's
+ configured in analog-pass-through mode.
+ enum: [1, 2, 3, 4]
+
+ qcom,dtest:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selects DTEST rail to route to GPIO when it's
+ configured as digital input.
+ enum: [1, 2, 3, 4]
+
+ qcom,amux-route:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selects the source for analog input. Valid values are defined in
+ <dt-bindings/pinctrl/qcom,pmic-mpp.h> PMIC_MPP_AMUX_ROUTE_CH5,
+ PMIC_MPP_AMUX_ROUTE_CH6...
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ qcom,paired:
+ - description:
+ Indicates that the pin should be operating in paired mode.
+
+ required:
+ - pins
+ - function
+
+ additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+ pm8841_mpp: mpps@a000 {
+ compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
+ reg = <0xa000 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pm8841_mpp 0 0 4>;
+ interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8841_default>;
+
+ default-state {
+ gpio {
+ pins = "mpp1", "mpp2", "mpp3", "mpp4";
+ function = "digital";
+ input-enable;
+ power-source = <PM8841_MPP_S3>;
+ };
+ };
+ };
+...
Convert Qualcomm PMIC MPP bindings from .txt to .yaml format. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- .../bindings/pinctrl/qcom,pmic-mpp.txt | 187 ------------------ .../bindings/pinctrl/qcom,pmic-mpp.yaml | 178 +++++++++++++++++ 2 files changed, 178 insertions(+), 187 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml -- 2.30.2