@@ -64,11 +64,13 @@ struct sgpio_properties {
#define SGPIO_LUTON_BIT_SOURCE GENMASK(11, 0)
#define SGPIO_OCELOT_AUTO_REPEAT BIT(10)
+#define SGPIO_OCELOT_SINGLE_SHOT BIT(11)
#define SGPIO_OCELOT_PORT_WIDTH GENMASK(8, 7)
#define SGPIO_OCELOT_CLK_FREQ GENMASK(19, 8)
#define SGPIO_OCELOT_BIT_SOURCE GENMASK(23, 12)
#define SGPIO_SPARX5_AUTO_REPEAT BIT(6)
+#define SGPIO_SPARX5_SINGLE_SHOT BIT(7)
#define SGPIO_SPARX5_PORT_WIDTH GENMASK(4, 3)
#define SGPIO_SPARX5_CLK_FREQ GENMASK(19, 8)
#define SGPIO_SPARX5_BIT_SOURCE GENMASK(23, 12)
@@ -118,6 +120,8 @@ struct sgpio_priv {
struct regmap *regs;
const struct sgpio_properties *properties;
spinlock_t lock;
+ /* protects the config register and single shot mode */
+ struct mutex poll_lock;
};
struct sgpio_port_addr {
@@ -225,12 +229,64 @@ static inline void sgpio_configure_clock(struct sgpio_priv *priv, u32 clkfrq)
sgpio_clrsetbits(priv, REG_SIO_CLOCK, 0, clr, set);
}
+static int sgpio_single_shot(struct sgpio_priv *priv)
+{
+ u32 addr = sgpio_get_addr(priv, REG_SIO_CONFIG, 0);
+ int ret, ret2;
+ u32 ctrl;
+ unsigned int single_shot;
+ unsigned int auto_repeat;
+
+ switch (priv->properties->arch) {
+ case SGPIO_ARCH_LUTON:
+ /* not supported for now */
+ return 0;
+ case SGPIO_ARCH_OCELOT:
+ single_shot = SGPIO_OCELOT_SINGLE_SHOT;
+ auto_repeat = SGPIO_OCELOT_AUTO_REPEAT;
+ break;
+ case SGPIO_ARCH_SPARX5:
+ single_shot = SGPIO_SPARX5_SINGLE_SHOT;
+ auto_repeat = SGPIO_SPARX5_AUTO_REPEAT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /*
+ * Trigger immediate burst. This only works when auto repeat is turned
+ * off. Otherwise, the single shot bit will never be cleared by the
+ * hardware. Measurements showed that an update might take as long as
+ * the burst gap. On a LAN9668 this is about 50ms for the largest
+ * setting.
+ * After the manual burst, reenable the auto repeat mode again.
+ */
+ mutex_lock(&priv->poll_lock);
+ ret = regmap_update_bits(priv->regs, addr, single_shot | auto_repeat,
+ single_shot);
+ if (ret)
+ goto out;
+
+ ret = regmap_read_poll_timeout(priv->regs, addr, ctrl,
+ !(ctrl & single_shot), 100, 60000);
+
+ /* reenable auto repeat mode even if there was an error */
+ ret2 = regmap_update_bits(priv->regs, addr, auto_repeat, auto_repeat);
+out:
+ mutex_unlock(&priv->poll_lock);
+
+ return ret ?: ret2;
+}
+
static int sgpio_output_set(struct sgpio_priv *priv,
struct sgpio_port_addr *addr,
int value)
{
unsigned int bit = SGPIO_SRC_BITS * addr->bit;
+ u32 reg = sgpio_get_addr(priv, REG_PORT_CONFIG, addr->port);
+ bool changed;
u32 clr, set;
+ int ret;
switch (priv->properties->arch) {
case SGPIO_ARCH_LUTON:
@@ -249,7 +305,16 @@ static int sgpio_output_set(struct sgpio_priv *priv,
return -EINVAL;
}
- sgpio_clrsetbits(priv, REG_PORT_CONFIG, addr->port, clr, set);
+ ret = regmap_update_bits_check(priv->regs, reg, clr | set, set,
+ &changed);
+ if (ret)
+ return ret;
+
+ if (changed) {
+ ret = sgpio_single_shot(priv);
+ if (ret)
+ return ret;
+ }
return 0;
}
@@ -788,6 +853,7 @@ static int microchip_sgpio_register_bank(struct device *dev,
gc->of_gpio_n_cells = 3;
gc->base = -1;
gc->ngpio = ngpios;
+ gc->can_sleep = !bank->is_input;
if (bank->is_input && priv->properties->flags & SGPIO_FLAGS_HAS_IRQ) {
int irq = fwnode_irq_get(fwnode, 0);
@@ -848,6 +914,7 @@ static int microchip_sgpio_probe(struct platform_device *pdev)
priv->dev = dev;
spin_lock_init(&priv->lock);
+ mutex_init(&priv->poll_lock);
reset = devm_reset_control_get_optional_shared(&pdev->dev, "switch");
if (IS_ERR(reset))
Right now, when a gpio value is set, the actual hardware pin gets set asynchronously. When linux write the output register, it takes some time until it is actually propagated to the output shift registers. If that output port is connected to an I2C mux for example, the linux driver assumes the I2C bus is already switched although it is not. Fortunately, there is a single shot mode with a feedback: you can trigger the single shot and the hardware will clear that bit once it has finished the clocking and strobed the load signal of the shift registers. This can take a considerable amount of time though. Measuremens have shown that it takes up to a whole burst cycle gap which is about 50ms on the largest setting. Therefore, we have to mark the output bank as sleepable. To avoid unnecessary waiting, just trigger the single shot if the value was actually changed. Signed-off-by: Michael Walle <michael@walle.cc> --- drivers/pinctrl/pinctrl-microchip-sgpio.c | 69 ++++++++++++++++++++++- 1 file changed, 68 insertions(+), 1 deletion(-)