| Message ID | 20221220005529.34744-3-hal.feng@starfivetech.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Basic pinctrl support for StarFive JH7110 RISC-V SoC | expand |
On Tue, Dec 20, 2022 at 08:55:26AM +0800, Hal Feng wrote: > From: Jianlong Huang <jianlong.huang@starfivetech.com> > > Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller. > > Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com> > Co-developed-by: Emil Renner Berthing <kernel@esmil.dk> > Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> > Signed-off-by: Hal Feng <hal.feng@starfivetech.com> > --- > .../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 142 ++++++++++++++++++ > MAINTAINERS | 3 +- > .../pinctrl/starfive,jh7110-pinctrl.h | 115 ++++++++++++++ > 3 files changed, 259 insertions(+), 1 deletion(-) > create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml > create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h > > diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml > new file mode 100644 > index 000000000000..60e616af2201 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml > @@ -0,0 +1,142 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: StarFive JH7110 Sys Pin Controller > + > +description: | > + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd. > + > + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63 > + can be multiplexed and have configurable bias, drive strength, > + schmitt trigger etc. > + Some peripherals have their I/O go through the 64 "GPIOs". This also > + includes a number of other UARTs, I2Cs, SPIs, PWMs etc. > + All these peripherals are connected to all 64 GPIOs such that > + any GPIO can be set up to be controlled by any of the peripherals. > + > +maintainers: > + - Jianlong Huang <jianlong.huang@starfivetech.com> > + > +properties: > + compatible: > + const: starfive,jh7110-sys-pinctrl > + > + reg: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + interrupt-controller: true > + > + '#interrupt-cells': > + const: 2 > + > + gpio-controller: true > + > + '#gpio-cells': > + const: 2 > + > +patternProperties: > + '-[0-9]+$': > + type: object > + patternProperties: > + '-pins$': > + type: object > + description: | > + A pinctrl node should contain at least one subnode representing the > + pinctrl groups available on the machine. Each subnode will list the > + pins it needs, and how they should be configured, with regard to > + muxer configuration, system signal configuration, pin groups for > + vin/vout module, pin voltage, mux functions for output, mux functions > + for output enable, mux functions for input. > + > + properties: > + pinmux: > + description: | > + The list of GPIOs and their mux settings that properties in the > + node apply to. This should be set using the GPIOMUX macro. > + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux Generally, don't reference individual properties. Instead, '-pins$' needs a $ref to pinmux-node.yaml. > + > + bias-disable: true > + > + bias-pull-up: > + type: boolean > + > + bias-pull-down: > + type: boolean > + > + drive-strength: > + enum: [ 2, 4, 8, 12 ] > + > + input-enable: true > + > + input-disable: true > + > + input-schmitt-enable: true > + > + input-schmitt-disable: true > + > + slew-rate: > + maximum: 1 > + > + additionalProperties: false > + > + additionalProperties: false It's easier to read if you put these at the beginning before a long properties section. > + > +required: > + - compatible > + - reg > + - clocks > + - interrupts > + - interrupt-controller > + - '#interrupt-cells' > + - gpio-controller > + - '#gpio-cells' > + > +additionalProperties: false > + > +examples: > + - | > + gpio@13040000 { > + compatible = "starfive,jh7110-sys-pinctrl"; > + reg = <0x13040000 0x10000>; > + clocks = <&syscrg 112>; > + resets = <&syscrg 2>; > + interrupts = <86>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-controller; > + #gpio-cells = <2>; > + > + uart0-0 { > + tx-pins { > + pinmux = <0xff140005>; > + bias-disable; > + drive-strength = <12>; > + input-disable; > + input-schmitt-disable; > + slew-rate = <0>; > + }; > + > + rx-pins { > + pinmux = <0x0E000406>; > + bias-pull-up; > + drive-strength = <2>; > + input-enable; > + input-schmitt-enable; > + slew-rate = <0>; > + }; > + }; > + }; > + > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index e0ffe584030b..57fd051ff4e8 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -19645,10 +19645,11 @@ M: Emil Renner Berthing <kernel@esmil.dk> > M: Jianlong Huang <jianlong.huang@starfivetech.com> > L: linux-gpio@vger.kernel.org > S: Maintained > -F: Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml > +F: Documentation/devicetree/bindings/pinctrl/starfive,jh71*.yaml > F: arch/riscv/boot/dts/starfive/jh7110-pinfunc.h > F: drivers/pinctrl/starfive/ > F: include/dt-bindings/pinctrl/pinctrl-starfive-jh7100.h > +F: include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h > > STARFIVE JH71X0 RESET CONTROLLER DRIVERS > M: Emil Renner Berthing <kernel@esmil.dk> > diff --git a/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h > new file mode 100644 > index 000000000000..c97dde8e864c > --- /dev/null > +++ b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h > @@ -0,0 +1,115 @@ > +/* SPDX-License-Identifier: GPL-2.0 OR MIT */ > +/* > + * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk> > + * Copyright (C) 2022 StarFive Technology Co., Ltd. > + */ > + > +#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__ > +#define __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__ > + > +/* sys_iomux pin */ > +#define PAD_GPIO0 0 > +#define PAD_GPIO1 1 > +#define PAD_GPIO2 2 > +#define PAD_GPIO3 3 > +#define PAD_GPIO4 4 > +#define PAD_GPIO5 5 > +#define PAD_GPIO6 6 > +#define PAD_GPIO7 7 > +#define PAD_GPIO8 8 > +#define PAD_GPIO9 9 > +#define PAD_GPIO10 10 > +#define PAD_GPIO11 11 > +#define PAD_GPIO12 12 > +#define PAD_GPIO13 13 > +#define PAD_GPIO14 14 > +#define PAD_GPIO15 15 > +#define PAD_GPIO16 16 > +#define PAD_GPIO17 17 > +#define PAD_GPIO18 18 > +#define PAD_GPIO19 19 > +#define PAD_GPIO20 20 > +#define PAD_GPIO21 21 > +#define PAD_GPIO22 22 > +#define PAD_GPIO23 23 > +#define PAD_GPIO24 24 > +#define PAD_GPIO25 25 > +#define PAD_GPIO26 26 > +#define PAD_GPIO27 27 > +#define PAD_GPIO28 28 > +#define PAD_GPIO29 29 > +#define PAD_GPIO30 30 > +#define PAD_GPIO31 31 > +#define PAD_GPIO32 32 > +#define PAD_GPIO33 33 > +#define PAD_GPIO34 34 > +#define PAD_GPIO35 35 > +#define PAD_GPIO36 36 > +#define PAD_GPIO37 37 > +#define PAD_GPIO38 38 > +#define PAD_GPIO39 39 > +#define PAD_GPIO40 40 > +#define PAD_GPIO41 41 > +#define PAD_GPIO42 42 > +#define PAD_GPIO43 43 > +#define PAD_GPIO44 44 > +#define PAD_GPIO45 45 > +#define PAD_GPIO46 46 > +#define PAD_GPIO47 47 > +#define PAD_GPIO48 48 > +#define PAD_GPIO49 49 > +#define PAD_GPIO50 50 > +#define PAD_GPIO51 51 > +#define PAD_GPIO52 52 > +#define PAD_GPIO53 53 > +#define PAD_GPIO54 54 > +#define PAD_GPIO55 55 > +#define PAD_GPIO56 56 > +#define PAD_GPIO57 57 > +#define PAD_GPIO58 58 > +#define PAD_GPIO59 59 > +#define PAD_GPIO60 60 > +#define PAD_GPIO61 61 > +#define PAD_GPIO62 62 > +#define PAD_GPIO63 63 > +#define PAD_SD0_CLK 64 > +#define PAD_SD0_CMD 65 > +#define PAD_SD0_DATA0 66 > +#define PAD_SD0_DATA1 67 > +#define PAD_SD0_DATA2 68 > +#define PAD_SD0_DATA3 69 > +#define PAD_SD0_DATA4 70 > +#define PAD_SD0_DATA5 71 > +#define PAD_SD0_DATA6 72 > +#define PAD_SD0_DATA7 73 > +#define PAD_SD0_STRB 74 > +#define PAD_GMAC1_MDC 75 > +#define PAD_GMAC1_MDIO 76 > +#define PAD_GMAC1_RXD0 77 > +#define PAD_GMAC1_RXD1 78 > +#define PAD_GMAC1_RXD2 79 > +#define PAD_GMAC1_RXD3 80 > +#define PAD_GMAC1_RXDV 81 > +#define PAD_GMAC1_RXC 82 > +#define PAD_GMAC1_TXD0 83 > +#define PAD_GMAC1_TXD1 84 > +#define PAD_GMAC1_TXD2 85 > +#define PAD_GMAC1_TXD3 86 > +#define PAD_GMAC1_TXEN 87 > +#define PAD_GMAC1_TXC 88 > +#define PAD_QSPI_SCLK 89 > +#define PAD_QSPI_CS0 90 > +#define PAD_QSPI_DATA0 91 > +#define PAD_QSPI_DATA1 92 > +#define PAD_QSPI_DATA2 93 > +#define PAD_QSPI_DATA3 94 > + > +#define GPOUT_LOW 0 > +#define GPOUT_HIGH 1 > + > +#define GPOEN_ENABLE 0 > +#define GPOEN_DISABLE 1 > + > +#define GPI_NONE 255 > + > +#endif > -- > 2.38.1 > >
On Tue, 20 Dec 2022 14:19:20 -0600, Rob Herring wrote: > On Tue, Dec 20, 2022 at 08:55:26AM +0800, Hal Feng wrote: >> From: Jianlong Huang <jianlong.huang@starfivetech.com> >> >> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller. >> >> Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com> >> Co-developed-by: Emil Renner Berthing <kernel@esmil.dk> >> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> >> Signed-off-by: Hal Feng <hal.feng@starfivetech.com> >> --- >> .../pinctrl/starfive,jh7110-sys-pinctrl.yaml | 142 ++++++++++++++++++ >> MAINTAINERS | 3 +- >> .../pinctrl/starfive,jh7110-pinctrl.h | 115 ++++++++++++++ >> 3 files changed, 259 insertions(+), 1 deletion(-) >> create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml >> create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h >> >> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml >> new file mode 100644 >> index 000000000000..60e616af2201 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml >> @@ -0,0 +1,142 @@ >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: StarFive JH7110 Sys Pin Controller >> + >> +description: | >> + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd. >> + >> + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63 >> + can be multiplexed and have configurable bias, drive strength, >> + schmitt trigger etc. >> + Some peripherals have their I/O go through the 64 "GPIOs". This also >> + includes a number of other UARTs, I2Cs, SPIs, PWMs etc. >> + All these peripherals are connected to all 64 GPIOs such that >> + any GPIO can be set up to be controlled by any of the peripherals. >> + >> +maintainers: >> + - Jianlong Huang <jianlong.huang@starfivetech.com> >> + >> +properties: >> + compatible: >> + const: starfive,jh7110-sys-pinctrl >> + >> + reg: >> + maxItems: 1 >> + >> + clocks: >> + maxItems: 1 >> + >> + resets: >> + maxItems: 1 >> + >> + interrupts: >> + maxItems: 1 >> + >> + interrupt-controller: true >> + >> + '#interrupt-cells': >> + const: 2 >> + >> + gpio-controller: true >> + >> + '#gpio-cells': >> + const: 2 >> + >> +patternProperties: >> + '-[0-9]+$': >> + type: object >> + patternProperties: >> + '-pins$': >> + type: object >> + description: | >> + A pinctrl node should contain at least one subnode representing the >> + pinctrl groups available on the machine. Each subnode will list the >> + pins it needs, and how they should be configured, with regard to >> + muxer configuration, system signal configuration, pin groups for >> + vin/vout module, pin voltage, mux functions for output, mux functions >> + for output enable, mux functions for input. >> + >> + properties: >> + pinmux: >> + description: | >> + The list of GPIOs and their mux settings that properties in the >> + node apply to. This should be set using the GPIOMUX macro. >> + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux > > Generally, don't reference individual properties. Instead, '-pins$' > needs a $ref to pinmux-node.yaml. Sorry for the late reply. '-pins$' miss a $ref to pincfg-node.yaml here. I will add it in the next version. 'pinmux' is not a property in pincfg-node.yaml, but a property in pinmux-node.yaml, so need a individual reference. > >> + >> + bias-disable: true >> + >> + bias-pull-up: >> + type: boolean >> + >> + bias-pull-down: >> + type: boolean >> + >> + drive-strength: >> + enum: [ 2, 4, 8, 12 ] >> + >> + input-enable: true >> + >> + input-disable: true >> + >> + input-schmitt-enable: true >> + >> + input-schmitt-disable: true >> + >> + slew-rate: >> + maximum: 1 >> + > >> + additionalProperties: false >> + >> + additionalProperties: false > > It's easier to read if you put these at the beginning before a long > properties section. Will fix it. Thank you for your feedback. Best regards, Hal > >> + >> +required: >> + - compatible >> + - reg >> + - clocks >> + - interrupts >> + - interrupt-controller >> + - '#interrupt-cells' >> + - gpio-controller >> + - '#gpio-cells' >> + >> +additionalProperties: false >> + >> +examples: >> + - | >> + gpio@13040000 { >> + compatible = "starfive,jh7110-sys-pinctrl"; >> + reg = <0x13040000 0x10000>; >> + clocks = <&syscrg 112>; >> + resets = <&syscrg 2>; >> + interrupts = <86>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + >> + uart0-0 { >> + tx-pins { >> + pinmux = <0xff140005>; >> + bias-disable; >> + drive-strength = <12>; >> + input-disable; >> + input-schmitt-disable; >> + slew-rate = <0>; >> + }; >> + >> + rx-pins { >> + pinmux = <0x0E000406>; >> + bias-pull-up; >> + drive-strength = <2>; >> + input-enable; >> + input-schmitt-enable; >> + slew-rate = <0>; >> + }; >> + }; >> + };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml new file mode 100644 index 000000000000..60e616af2201 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH7110 Sys Pin Controller + +description: | + Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd. + + Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63 + can be multiplexed and have configurable bias, drive strength, + schmitt trigger etc. + Some peripherals have their I/O go through the 64 "GPIOs". This also + includes a number of other UARTs, I2Cs, SPIs, PWMs etc. + All these peripherals are connected to all 64 GPIOs such that + any GPIO can be set up to be controlled by any of the peripherals. + +maintainers: + - Jianlong Huang <jianlong.huang@starfivetech.com> + +properties: + compatible: + const: starfive,jh7110-sys-pinctrl + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + gpio-controller: true + + '#gpio-cells': + const: 2 + +patternProperties: + '-[0-9]+$': + type: object + patternProperties: + '-pins$': + type: object + description: | + A pinctrl node should contain at least one subnode representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to + muxer configuration, system signal configuration, pin groups for + vin/vout module, pin voltage, mux functions for output, mux functions + for output enable, mux functions for input. + + properties: + pinmux: + description: | + The list of GPIOs and their mux settings that properties in the + node apply to. This should be set using the GPIOMUX macro. + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux + + bias-disable: true + + bias-pull-up: + type: boolean + + bias-pull-down: + type: boolean + + drive-strength: + enum: [ 2, 4, 8, 12 ] + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + slew-rate: + maximum: 1 + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + +additionalProperties: false + +examples: + - | + gpio@13040000 { + compatible = "starfive,jh7110-sys-pinctrl"; + reg = <0x13040000 0x10000>; + clocks = <&syscrg 112>; + resets = <&syscrg 2>; + interrupts = <86>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + uart0-0 { + tx-pins { + pinmux = <0xff140005>; + bias-disable; + drive-strength = <12>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + + rx-pins { + pinmux = <0x0E000406>; + bias-pull-up; + drive-strength = <2>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + }; + }; + +... diff --git a/MAINTAINERS b/MAINTAINERS index e0ffe584030b..57fd051ff4e8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -19645,10 +19645,11 @@ M: Emil Renner Berthing <kernel@esmil.dk> M: Jianlong Huang <jianlong.huang@starfivetech.com> L: linux-gpio@vger.kernel.org S: Maintained -F: Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml +F: Documentation/devicetree/bindings/pinctrl/starfive,jh71*.yaml F: arch/riscv/boot/dts/starfive/jh7110-pinfunc.h F: drivers/pinctrl/starfive/ F: include/dt-bindings/pinctrl/pinctrl-starfive-jh7100.h +F: include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h STARFIVE JH71X0 RESET CONTROLLER DRIVERS M: Emil Renner Berthing <kernel@esmil.dk> diff --git a/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h new file mode 100644 index 000000000000..c97dde8e864c --- /dev/null +++ b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h @@ -0,0 +1,115 @@ +/* SPDX-License-Identifier: GPL-2.0 OR MIT */ +/* + * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk> + * Copyright (C) 2022 StarFive Technology Co., Ltd. + */ + +#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__ +#define __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__ + +/* sys_iomux pin */ +#define PAD_GPIO0 0 +#define PAD_GPIO1 1 +#define PAD_GPIO2 2 +#define PAD_GPIO3 3 +#define PAD_GPIO4 4 +#define PAD_GPIO5 5 +#define PAD_GPIO6 6 +#define PAD_GPIO7 7 +#define PAD_GPIO8 8 +#define PAD_GPIO9 9 +#define PAD_GPIO10 10 +#define PAD_GPIO11 11 +#define PAD_GPIO12 12 +#define PAD_GPIO13 13 +#define PAD_GPIO14 14 +#define PAD_GPIO15 15 +#define PAD_GPIO16 16 +#define PAD_GPIO17 17 +#define PAD_GPIO18 18 +#define PAD_GPIO19 19 +#define PAD_GPIO20 20 +#define PAD_GPIO21 21 +#define PAD_GPIO22 22 +#define PAD_GPIO23 23 +#define PAD_GPIO24 24 +#define PAD_GPIO25 25 +#define PAD_GPIO26 26 +#define PAD_GPIO27 27 +#define PAD_GPIO28 28 +#define PAD_GPIO29 29 +#define PAD_GPIO30 30 +#define PAD_GPIO31 31 +#define PAD_GPIO32 32 +#define PAD_GPIO33 33 +#define PAD_GPIO34 34 +#define PAD_GPIO35 35 +#define PAD_GPIO36 36 +#define PAD_GPIO37 37 +#define PAD_GPIO38 38 +#define PAD_GPIO39 39 +#define PAD_GPIO40 40 +#define PAD_GPIO41 41 +#define PAD_GPIO42 42 +#define PAD_GPIO43 43 +#define PAD_GPIO44 44 +#define PAD_GPIO45 45 +#define PAD_GPIO46 46 +#define PAD_GPIO47 47 +#define PAD_GPIO48 48 +#define PAD_GPIO49 49 +#define PAD_GPIO50 50 +#define PAD_GPIO51 51 +#define PAD_GPIO52 52 +#define PAD_GPIO53 53 +#define PAD_GPIO54 54 +#define PAD_GPIO55 55 +#define PAD_GPIO56 56 +#define PAD_GPIO57 57 +#define PAD_GPIO58 58 +#define PAD_GPIO59 59 +#define PAD_GPIO60 60 +#define PAD_GPIO61 61 +#define PAD_GPIO62 62 +#define PAD_GPIO63 63 +#define PAD_SD0_CLK 64 +#define PAD_SD0_CMD 65 +#define PAD_SD0_DATA0 66 +#define PAD_SD0_DATA1 67 +#define PAD_SD0_DATA2 68 +#define PAD_SD0_DATA3 69 +#define PAD_SD0_DATA4 70 +#define PAD_SD0_DATA5 71 +#define PAD_SD0_DATA6 72 +#define PAD_SD0_DATA7 73 +#define PAD_SD0_STRB 74 +#define PAD_GMAC1_MDC 75 +#define PAD_GMAC1_MDIO 76 +#define PAD_GMAC1_RXD0 77 +#define PAD_GMAC1_RXD1 78 +#define PAD_GMAC1_RXD2 79 +#define PAD_GMAC1_RXD3 80 +#define PAD_GMAC1_RXDV 81 +#define PAD_GMAC1_RXC 82 +#define PAD_GMAC1_TXD0 83 +#define PAD_GMAC1_TXD1 84 +#define PAD_GMAC1_TXD2 85 +#define PAD_GMAC1_TXD3 86 +#define PAD_GMAC1_TXEN 87 +#define PAD_GMAC1_TXC 88 +#define PAD_QSPI_SCLK 89 +#define PAD_QSPI_CS0 90 +#define PAD_QSPI_DATA0 91 +#define PAD_QSPI_DATA1 92 +#define PAD_QSPI_DATA2 93 +#define PAD_QSPI_DATA3 94 + +#define GPOUT_LOW 0 +#define GPOUT_HIGH 1 + +#define GPOEN_ENABLE 0 +#define GPOEN_DISABLE 1 + +#define GPI_NONE 255 + +#endif