diff mbox series

[v2,01/17] regulator: bd718x7, bd71828, Fix dvs voltage levels

Message ID 7b7a9111e02e06574849bacd5703e6c5cdcd2206.1611037866.git.matti.vaittinen@fi.rohmeurope.com
State Accepted
Commit c294554111a835598b557db789d9ad2379b512a2
Headers show
Series Support ROHM BD71815 PMIC | expand

Commit Message

Vaittinen, Matti Jan. 19, 2021, 7:14 a.m. UTC
The ROHM BD718x7 and BD71828 drivers support setting HW state
specific voltages from device-tree. This is used also by various
in-tree DTS files.

These drivers do incorrectly try to compose bit-map using enum
values. By a chance this works for first two valid levels having
values 1 and 2 - but setting values for the rest of the levels
do indicate capbility of setting values for first levels as
well. Luckily the regulators which support settin values for
SUSPEND/LPSR do usually also support setting values for RUN
and IDLE too - thus this has not been such a fatal issue.

Fix this by defining the old enum values as bits and using
new enum in parsing code. This allows keeping existing IC
specific drivers intact and only adding the defines and
slightly changing the rohm-regulator.c

Fixes: 21b72156ede8b ("regulator: bd718x7: Split driver to common and bd718x7 specific parts")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---

Please note that this same change has been sent individually:
https://lore.kernel.org/lkml/20210118075851.GA1016281@localhost.localdomain/
It is present in this series only because some patches depend on it.

 drivers/regulator/rohm-regulator.c |  9 ++++++---
 include/linux/mfd/rohm-generic.h   | 14 ++++++--------
 2 files changed, 12 insertions(+), 11 deletions(-)
diff mbox series

Patch

diff --git a/drivers/regulator/rohm-regulator.c b/drivers/regulator/rohm-regulator.c
index 399002383b28..5c558b153d55 100644
--- a/drivers/regulator/rohm-regulator.c
+++ b/drivers/regulator/rohm-regulator.c
@@ -52,9 +52,12 @@  int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
 	char *prop;
 	unsigned int reg, mask, omask, oreg = desc->enable_reg;
 
-	for (i = 0; i < ROHM_DVS_LEVEL_MAX && !ret; i++) {
-		if (dvs->level_map & (1 << i)) {
-			switch (i + 1) {
+	for (i = 0; i < ROHM_DVS_LEVEL_VALID_AMOUNT && !ret; i++) {
+		int bit;
+
+		bit = BIT(i);
+		if (dvs->level_map & bit) {
+			switch (bit) {
 			case ROHM_DVS_LEVEL_RUN:
 				prop = "rohm,dvs-run-voltage";
 				reg = dvs->run_reg;
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index 4283b5b33e04..2b85b9deb03a 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -20,14 +20,12 @@  struct rohm_regmap_dev {
 	struct regmap *regmap;
 };
 
-enum {
-	ROHM_DVS_LEVEL_UNKNOWN,
-	ROHM_DVS_LEVEL_RUN,
-	ROHM_DVS_LEVEL_IDLE,
-	ROHM_DVS_LEVEL_SUSPEND,
-	ROHM_DVS_LEVEL_LPSR,
-	ROHM_DVS_LEVEL_MAX = ROHM_DVS_LEVEL_LPSR,
-};
+#define ROHM_DVS_LEVEL_RUN		BIT(0)
+#define ROHM_DVS_LEVEL_IDLE		BIT(1)
+#define ROHM_DVS_LEVEL_SUSPEND		BIT(2)
+#define ROHM_DVS_LEVEL_LPSR		BIT(3)
+#define ROHM_DVS_LEVEL_VALID_AMOUNT	4
+#define ROHM_DVS_LEVEL_UNKNOWN		0
 
 /**
  * struct rohm_dvs_config - dynamic voltage scaling register descriptions