@@ -494,6 +494,81 @@
wcnss@a21b000 {
status = "okay";
};
+
+ camera_vdddo_1v8: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vdddo";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ camera_vdda_2v8: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vdda";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ camera_vddd_1v5: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "camera_vddd";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ cci@1b0c000 {
+ status = "ok";
+ i2c-bus@0 {
+ camera_rear@3b {
+ compatible = "ovti,ov5640";
+ reg = <0x3b>;
+
+ enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_default>;
+
+ clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+ clock-names = "xclk";
+ clock-frequency = <23880000>;
+
+ vdddo-supply = <&camera_vdddo_1v8>;
+ vdda-supply = <&camera_vdda_2v8>;
+ vddd-supply = <&camera_vddd_1v5>;
+
+ /* No camera mezzanine by default */
+ status = "okay";
+
+ port {
+ ov5640_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2>;
+ remote-endpoint = <&csiphy0_ep>;
+ };
+ };
+ };
+ };
+ };
+
+ camss@1b00000 {
+ status = "ok";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ csiphy0_ep: endpoint {
+ clock-lanes = <1>;
+ data-lanes = <0 2>;
+ remote-endpoint = <&ov5640_ep>;
+ status = "okay";
+ };
+ };
+ };
+ };
};
usb2513 {
@@ -1451,6 +1451,33 @@
};
};
+ cci@1b0c000 {
+ compatible = "qcom,msm8916-cci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1b0c000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>,
+ <&gcc GCC_CAMSS_CCI_AHB_CLK>,
+ <&gcc GCC_CAMSS_CCI_CLK>,
+ <&gcc GCC_CAMSS_AHB_CLK>;
+ clock-names = "camss_top_ahb", "cci_ahb",
+ "cci", "camss_ahb";
+ assigned-clocks = <&gcc GCC_CAMSS_CCI_AHB_CLK>,
+ <&gcc GCC_CAMSS_CCI_CLK>;
+ assigned-clock-rates = <80000000>, <19200000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cci0_default>;
+ status = "disabled";
+
+ i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <400000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
camss: camss@1b00000 {
compatible = "qcom,msm8916-camss";
reg = <0x1b0ac00 0x200>,
Add cci device to msm8916.dtsi. Add default 96boards camera node for db410c (apq8016-sbc). Signed-off-by: Loic Poulain <loic.poulain@linaro.org> --- v2: add this patch in the series arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 75 +++++++++++++++++++++++++++++++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 27 +++++++++++ 2 files changed, 102 insertions(+) -- 2.7.4