@@ -4040,6 +4040,7 @@ M: Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
L: linux-media@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
+F: drivers/media/platform/bcm2835/
BROADCOM BCM47XX MIPS ARCHITECTURE
M: Hauke Mehrtens <hauke@hauke-m.de>
@@ -67,6 +67,7 @@ source "drivers/media/platform/amlogic/Kconfig"
source "drivers/media/platform/amphion/Kconfig"
source "drivers/media/platform/aspeed/Kconfig"
source "drivers/media/platform/atmel/Kconfig"
+source "drivers/media/platform/broadcom/Kconfig"
source "drivers/media/platform/cadence/Kconfig"
source "drivers/media/platform/chips-media/Kconfig"
source "drivers/media/platform/intel/Kconfig"
@@ -10,6 +10,7 @@ obj-y += amlogic/
obj-y += amphion/
obj-y += aspeed/
obj-y += atmel/
+obj-y += broadcom/
obj-y += cadence/
obj-y += chips-media/
obj-y += intel/
new file mode 100644
@@ -0,0 +1,23 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config VIDEO_BCM2835_UNICAM
+ tristate "Broadcom BCM283x/BCM271x Unicam video capture driver"
+ depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on PM
+ depends on VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select V4L2_FWNODE
+ select VIDEO_V4L2_SUBDEV_API
+ select VIDEOBUF2_DMA_CONTIG
+ help
+ Say Y here to enable support for the BCM283x/BCM271x CSI-2 receiver.
+ This is a V4L2 driver that controls the CSI-2 receiver directly,
+ independently from the VC4 firmware.
+
+ This driver is mutually exclusive with the use of bcm2835-camera. The
+ firmware will disable all access to the peripheral from within the
+ firmware if it finds a DT node using it, and bcm2835-camera will
+ therefore fail to probe.
+
+ To compile this driver as a module, choose M here. The module will be
+ called bcm2835-unicam.
new file mode 100644
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_VIDEO_BCM2835_UNICAM) += bcm2835-unicam.o
new file mode 100644
@@ -0,0 +1,246 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+/*
+ * Copyright (C) 2017-2020 Raspberry Pi Trading.
+ * Dave Stevenson <dave.stevenson@raspberrypi.com>
+ */
+
+#ifndef VC4_REGS_UNICAM_H
+#define VC4_REGS_UNICAM_H
+
+#include <linux/bits.h>
+
+/*
+ * The following values are taken from files found within the code drop
+ * made by Broadcom for the BCM21553 Graphics Driver, predominantly in
+ * brcm_usrlib/dag/vmcsx/vcinclude/hardware_vc4.h.
+ * They have been modified to be only the register offset.
+ */
+#define UNICAM_CTRL 0x000
+#define UNICAM_STA 0x004
+#define UNICAM_ANA 0x008
+#define UNICAM_PRI 0x00c
+#define UNICAM_CLK 0x010
+#define UNICAM_CLT 0x014
+#define UNICAM_DAT0 0x018
+#define UNICAM_DAT1 0x01c
+#define UNICAM_DAT2 0x020
+#define UNICAM_DAT3 0x024
+#define UNICAM_DLT 0x028
+#define UNICAM_CMP0 0x02c
+#define UNICAM_CMP1 0x030
+#define UNICAM_CAP0 0x034
+#define UNICAM_CAP1 0x038
+#define UNICAM_ICTL 0x100
+#define UNICAM_ISTA 0x104
+#define UNICAM_IDI0 0x108
+#define UNICAM_IPIPE 0x10c
+#define UNICAM_IBSA0 0x110
+#define UNICAM_IBEA0 0x114
+#define UNICAM_IBLS 0x118
+#define UNICAM_IBWP 0x11c
+#define UNICAM_IHWIN 0x120
+#define UNICAM_IHSTA 0x124
+#define UNICAM_IVWIN 0x128
+#define UNICAM_IVSTA 0x12c
+#define UNICAM_ICC 0x130
+#define UNICAM_ICS 0x134
+#define UNICAM_IDC 0x138
+#define UNICAM_IDPO 0x13c
+#define UNICAM_IDCA 0x140
+#define UNICAM_IDCD 0x144
+#define UNICAM_IDS 0x148
+#define UNICAM_DCS 0x200
+#define UNICAM_DBSA0 0x204
+#define UNICAM_DBEA0 0x208
+#define UNICAM_DBWP 0x20c
+#define UNICAM_DBCTL 0x300
+#define UNICAM_IBSA1 0x304
+#define UNICAM_IBEA1 0x308
+#define UNICAM_IDI1 0x30c
+#define UNICAM_DBSA1 0x310
+#define UNICAM_DBEA1 0x314
+#define UNICAM_MISC 0x400
+
+/*
+ * The following bitmasks are from the kernel released by Broadcom
+ * for Android - https://android.googlesource.com/kernel/bcm/
+ * The Rhea, Hawaii, and Java chips all contain the same VideoCore4
+ * Unicam block as BCM2835, as defined in eg
+ * arch/arm/mach-rhea/include/mach/rdb_A0/brcm_rdb_cam.h and similar.
+ * Values reworked to use the kernel BIT and GENMASK macros.
+ *
+ * Some of the bit mnenomics have been amended to match the datasheet.
+ */
+/* UNICAM_CTRL Register */
+#define UNICAM_CPE BIT(0)
+#define UNICAM_MEM BIT(1)
+#define UNICAM_CPR BIT(2)
+#define UNICAM_CPM_MASK GENMASK(3, 3)
+#define UNICAM_CPM_CSI2 0
+#define UNICAM_CPM_CCP2 1
+#define UNICAM_SOE BIT(4)
+#define UNICAM_DCM_MASK GENMASK(5, 5)
+#define UNICAM_DCM_STROBE 0
+#define UNICAM_DCM_DATA 1
+#define UNICAM_SLS BIT(6)
+#define UNICAM_PFT_MASK GENMASK(11, 8)
+#define UNICAM_OET_MASK GENMASK(20, 12)
+
+/* UNICAM_STA Register */
+#define UNICAM_SYN BIT(0)
+#define UNICAM_CS BIT(1)
+#define UNICAM_SBE BIT(2)
+#define UNICAM_PBE BIT(3)
+#define UNICAM_HOE BIT(4)
+#define UNICAM_PLE BIT(5)
+#define UNICAM_SSC BIT(6)
+#define UNICAM_CRCE BIT(7)
+#define UNICAM_OES BIT(8)
+#define UNICAM_IFO BIT(9)
+#define UNICAM_OFO BIT(10)
+#define UNICAM_BFO BIT(11)
+#define UNICAM_DL BIT(12)
+#define UNICAM_PS BIT(13)
+#define UNICAM_IS BIT(14)
+#define UNICAM_PI0 BIT(15)
+#define UNICAM_PI1 BIT(16)
+#define UNICAM_FSI_S BIT(17)
+#define UNICAM_FEI_S BIT(18)
+#define UNICAM_LCI_S BIT(19)
+#define UNICAM_BUF0_RDY BIT(20)
+#define UNICAM_BUF0_NO BIT(21)
+#define UNICAM_BUF1_RDY BIT(22)
+#define UNICAM_BUF1_NO BIT(23)
+#define UNICAM_DI BIT(24)
+
+#define UNICAM_STA_MASK_ALL \
+ (UNICAM_SBE | UNICAM_PBE | UNICAM_HOE | UNICAM_PLE | UNICAM_SSC | \
+ UNICAM_CRCE | UNICAM_IFO | UNICAM_OFO | UNICAM_DL | UNICAM_PS | \
+ UNICAM_PI0 | UNICAM_PI1)
+
+/* UNICAM_ANA Register */
+#define UNICAM_APD BIT(0)
+#define UNICAM_BPD BIT(1)
+#define UNICAM_AR BIT(2)
+#define UNICAM_DDL BIT(3)
+#define UNICAM_CTATADJ_MASK GENMASK(7, 4)
+#define UNICAM_PTATADJ_MASK GENMASK(11, 8)
+
+/* UNICAM_PRI Register */
+#define UNICAM_PE BIT(0)
+#define UNICAM_PT_MASK GENMASK(2, 1)
+#define UNICAM_NP_MASK GENMASK(7, 4)
+#define UNICAM_PP_MASK GENMASK(11, 8)
+#define UNICAM_BS_MASK GENMASK(15, 12)
+#define UNICAM_BL_MASK GENMASK(17, 16)
+
+/* UNICAM_CLK Register */
+#define UNICAM_CLE BIT(0)
+#define UNICAM_CLPD BIT(1)
+#define UNICAM_CLLPE BIT(2)
+#define UNICAM_CLHSE BIT(3)
+#define UNICAM_CLTRE BIT(4)
+#define UNICAM_CLAC_MASK GENMASK(8, 5)
+#define UNICAM_CLSTE BIT(29)
+
+/* UNICAM_CLT Register */
+#define UNICAM_CLT1_MASK GENMASK(7, 0)
+#define UNICAM_CLT2_MASK GENMASK(15, 8)
+
+/* UNICAM_DATn Registers */
+#define UNICAM_DLE BIT(0)
+#define UNICAM_DLPD BIT(1)
+#define UNICAM_DLLPE BIT(2)
+#define UNICAM_DLHSE BIT(3)
+#define UNICAM_DLTRE BIT(4)
+#define UNICAM_DLSM BIT(5)
+#define UNICAM_DLFO BIT(28)
+#define UNICAM_DLSTE BIT(29)
+
+#define UNICAM_DAT_MASK_ALL (UNICAM_DLSTE | UNICAM_DLFO)
+
+/* UNICAM_DLT Register */
+#define UNICAM_DLT1_MASK GENMASK(7, 0)
+#define UNICAM_DLT2_MASK GENMASK(15, 8)
+#define UNICAM_DLT3_MASK GENMASK(23, 16)
+
+/* UNICAM_ICTL Register */
+#define UNICAM_FSIE BIT(0)
+#define UNICAM_FEIE BIT(1)
+#define UNICAM_IBOB BIT(2)
+#define UNICAM_FCM BIT(3)
+#define UNICAM_TFC BIT(4)
+#define UNICAM_LIP_MASK GENMASK(6, 5)
+#define UNICAM_LCIE_MASK GENMASK(28, 16)
+
+/* UNICAM_IDI0/1 Register */
+#define UNICAM_ID0_MASK GENMASK(7, 0)
+#define UNICAM_ID1_MASK GENMASK(15, 8)
+#define UNICAM_ID2_MASK GENMASK(23, 16)
+#define UNICAM_ID3_MASK GENMASK(31, 24)
+
+/* UNICAM_ISTA Register */
+#define UNICAM_FSI BIT(0)
+#define UNICAM_FEI BIT(1)
+#define UNICAM_LCI BIT(2)
+
+#define UNICAM_ISTA_MASK_ALL (UNICAM_FSI | UNICAM_FEI | UNICAM_LCI)
+
+/* UNICAM_IPIPE Register */
+#define UNICAM_PUM_MASK GENMASK(2, 0)
+/* Unpacking modes */
+#define UNICAM_PUM_NONE 0
+#define UNICAM_PUM_UNPACK6 1
+#define UNICAM_PUM_UNPACK7 2
+#define UNICAM_PUM_UNPACK8 3
+#define UNICAM_PUM_UNPACK10 4
+#define UNICAM_PUM_UNPACK12 5
+#define UNICAM_PUM_UNPACK14 6
+#define UNICAM_PUM_UNPACK16 7
+#define UNICAM_DDM_MASK GENMASK(6, 3)
+#define UNICAM_PPM_MASK GENMASK(9, 7)
+/* Packing modes */
+#define UNICAM_PPM_NONE 0
+#define UNICAM_PPM_PACK8 1
+#define UNICAM_PPM_PACK10 2
+#define UNICAM_PPM_PACK12 3
+#define UNICAM_PPM_PACK14 4
+#define UNICAM_PPM_PACK16 5
+#define UNICAM_DEM_MASK GENMASK(11, 10)
+#define UNICAM_DEBL_MASK GENMASK(14, 12)
+#define UNICAM_ICM_MASK GENMASK(16, 15)
+#define UNICAM_IDM_MASK GENMASK(17, 17)
+
+/* UNICAM_ICC Register */
+#define UNICAM_ICFL_MASK GENMASK(4, 0)
+#define UNICAM_ICFH_MASK GENMASK(9, 5)
+#define UNICAM_ICST_MASK GENMASK(12, 10)
+#define UNICAM_ICLT_MASK GENMASK(15, 13)
+#define UNICAM_ICLL_MASK GENMASK(31, 16)
+
+/* UNICAM_DCS Register */
+#define UNICAM_DIE BIT(0)
+#define UNICAM_DIM BIT(1)
+#define UNICAM_DBOB BIT(3)
+#define UNICAM_FDE BIT(4)
+#define UNICAM_LDP BIT(5)
+#define UNICAM_EDL_MASK GENMASK(15, 8)
+
+/* UNICAM_DBCTL Register */
+#define UNICAM_DBEN BIT(0)
+#define UNICAM_BUF0_IE BIT(1)
+#define UNICAM_BUF1_IE BIT(2)
+
+/* UNICAM_CMP[0,1] register */
+#define UNICAM_PCE BIT(31)
+#define UNICAM_GI BIT(9)
+#define UNICAM_CPH BIT(8)
+#define UNICAM_PCVC_MASK GENMASK(7, 6)
+#define UNICAM_PCDT_MASK GENMASK(5, 0)
+
+/* UNICAM_MISC register */
+#define UNICAM_FL0 BIT(6)
+#define UNICAM_FL1 BIT(9)
+
+#endif
new file mode 100644
@@ -0,0 +1,2671 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * BCM283x / BCM271x Unicam Capture Driver
+ *
+ * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd.
+ * Copyright (C) 2024 - Ideas on Board
+ *
+ * Dave Stevenson <dave.stevenson@raspberrypi.com>
+ *
+ * Based on TI am437x driver by
+ * Benoit Parrot <bparrot@ti.com>
+ * Lad, Prabhakar <prabhakar.csengg@gmail.com>
+ *
+ * and TI CAL camera interface driver by
+ * Benoit Parrot <bparrot@ti.com>
+ *
+ *
+ * There are two camera drivers in the kernel for BCM283x - this one and
+ * bcm2835-camera (currently in staging).
+ *
+ * This driver directly controls the Unicam peripheral - there is no
+ * involvement with the VideoCore firmware. Unicam receives CSI-2 or CCP2 data
+ * and writes it into SDRAM. The only potential processing options are to
+ * repack Bayer data into an alternate format, and applying windowing. The
+ * repacking does not shift the data, so can repack V4L2_PIX_FMT_Sxxxx10P to
+ * V4L2_PIX_FMT_Sxxxx10, or V4L2_PIX_FMT_Sxxxx12P to V4L2_PIX_FMT_Sxxxx12, but
+ * not generically up to V4L2_PIX_FMT_Sxxxx16. Support for windowing may be
+ * added later.
+ *
+ * It should be possible to connect this driver to any sensor with a suitable
+ * output interface and V4L2 subdevice driver.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-common.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mc.h>
+#include <media/videobuf2-dma-contig.h>
+
+#include "bcm2835-unicam-regs.h"
+
+#define UNICAM_MODULE_NAME "unicam"
+
+/*
+ * Unicam must request a minimum of 250Mhz from the VPU clock.
+ * Otherwise the input FIFOs overrun and cause image corruption.
+ */
+#define UNICAM_MIN_VPU_CLOCK_RATE (250 * 1000 * 1000)
+
+/* Unicam has an internal DMA alignment constraint of 16 bytes for each line. */
+#define UNICAM_DMA_BPL_ALIGNMENT 16
+
+/*
+ * The image stride is stored in a 16 bit register, and needs to be aligned to
+ * the DMA constraint. As the ISP in the same SoC has a 32 bytes alignment
+ * constraint on its input, set the image stride alignment to 32 bytes here as
+ * well to avoid incompatible configurations.
+ */
+#define UNICAM_IMAGE_BPL_ALIGNMENT 32
+#define UNICAM_IMAGE_MAX_BPL ((1U << 16) - UNICAM_IMAGE_BPL_ALIGNMENT)
+
+/*
+ * Max width is therefore determined by the max stride divided by the number of
+ * bits per pixel. Take 32bpp as a worst case. No imposed limit on the height,
+ * so adopt a square image for want of anything better.
+ */
+#define UNICAM_IMAGE_MIN_WIDTH 16
+#define UNICAM_IMAGE_MIN_HEIGHT 16
+#define UNICAM_IMAGE_MAX_WIDTH (UNICAM_IMAGE_MAX_BPL / 4)
+#define UNICAM_IMAGE_MAX_HEIGHT UNICAM_IMAGE_MAX_WIDTH
+
+/*
+ * There's no intrinsic limits on the width and height for embedded data. Use
+ * the same maximum values as for the image, to avoid overflows in the image
+ * size computation.
+ */
+#define UNICAM_META_MIN_WIDTH 1
+#define UNICAM_META_MIN_HEIGHT 1
+#define UNICAM_META_MAX_WIDTH UNICAM_IMAGE_MAX_WIDTH
+#define UNICAM_META_MAX_HEIGHT UNICAM_IMAGE_MAX_HEIGHT
+
+/*
+ * Size of the dummy buffer. Can be any size really, but the DMA
+ * allocation works in units of page sizes.
+ */
+#define UNICAM_DUMMY_BUF_SIZE PAGE_SIZE
+
+enum unicam_pad {
+ UNICAM_SD_PAD_SINK,
+ UNICAM_SD_PAD_SOURCE_IMAGE,
+ UNICAM_SD_PAD_SOURCE_METADATA,
+ UNICAM_SD_NUM_PADS
+};
+
+enum unicam_node_type {
+ UNICAM_IMAGE_NODE,
+ UNICAM_METADATA_NODE,
+ UNICAM_MAX_NODES
+};
+
+/*
+ * struct unicam_format_info - Unicam media bus format information
+ * @fourcc: V4L2 pixel format FCC identifier. 0 if n/a.
+ * @unpacked_fourcc: V4L2 pixel format FCC identifier if the data is expanded
+ * out to 16bpp. 0 if n/a.
+ * @code: V4L2 media bus format code.
+ * @depth: Bits per pixel as delivered from the source.
+ * @csi_dt: CSI data type.
+ * @unpack: PUM value when unpacking to @unpacked_fourcc
+ */
+struct unicam_format_info {
+ u32 fourcc;
+ u32 unpacked_fourcc;
+ u32 code;
+ u8 depth;
+ u8 csi_dt;
+ u8 unpack;
+};
+
+struct unicam_buffer {
+ struct vb2_v4l2_buffer vb;
+ struct list_head list;
+ dma_addr_t dma_addr;
+ unsigned int size;
+};
+
+static inline struct unicam_buffer *to_unicam_buffer(struct vb2_buffer *vb)
+{
+ return container_of(vb, struct unicam_buffer, vb.vb2_buf);
+}
+
+struct unicam_node {
+ bool registered;
+ bool streaming;
+ unsigned int id;
+
+ /* Pointer to the current v4l2_buffer */
+ struct unicam_buffer *cur_frm;
+ /* Pointer to the next v4l2_buffer */
+ struct unicam_buffer *next_frm;
+ /* video capture */
+ const struct unicam_format_info *fmtinfo;
+ /* Used to store current pixel format */
+ struct v4l2_format fmt;
+ /* Buffer queue used in video-buf */
+ struct vb2_queue buffer_queue;
+ /* Queue of filled frames */
+ struct list_head dma_queue;
+ /* IRQ lock for DMA queue */
+ spinlock_t dma_queue_lock;
+ /* Identifies video device for this channel */
+ struct video_device video_dev;
+ /* Pointer to the parent handle */
+ struct unicam_device *dev;
+ struct media_pad pad;
+ /*
+ * Dummy buffer intended to be used by unicam
+ * if we have no other queued buffers to swap to.
+ */
+ struct unicam_buffer dummy_buf;
+ void *dummy_buf_cpu_addr;
+};
+
+struct unicam_device {
+ struct kref kref;
+
+ /* peripheral base address */
+ void __iomem *base;
+ /* clock gating base address */
+ void __iomem *clk_gate_base;
+ /* lp clock handle */
+ struct clk *clock;
+ /* vpu clock handle */
+ struct clk *vpu_clock;
+ /* V4l2 device */
+ struct v4l2_device v4l2_dev;
+ struct media_device mdev;
+
+ /* parent device */
+ struct device *dev;
+ /* subdevice async notifier */
+ struct v4l2_async_notifier notifier;
+ unsigned int sequence;
+
+ /* Sensor node */
+ struct {
+ struct v4l2_subdev *subdev;
+ struct media_pad *pad;
+ } sensor;
+
+ /* Internal subdev */
+ struct {
+ struct v4l2_subdev sd;
+ struct media_pad pads[UNICAM_SD_NUM_PADS];
+ unsigned int enabled_streams;
+ } subdev;
+
+ enum v4l2_mbus_type bus_type;
+ /*
+ * Stores bus.mipi_csi2.flags for CSI2 sensors, or
+ * bus.mipi_csi1.strobe for CCP2.
+ */
+ unsigned int bus_flags;
+ unsigned int max_data_lanes;
+
+ struct {
+ struct media_pipeline pipe;
+ unsigned int num_data_lanes;
+ unsigned int nodes;
+ } pipe;
+
+ /* Lock used for the video devices of both nodes */
+ struct mutex lock;
+ struct unicam_node node[UNICAM_MAX_NODES];
+};
+
+static inline struct unicam_device *
+notifier_to_unicam_device(struct v4l2_async_notifier *notifier)
+{
+ return container_of(notifier, struct unicam_device, notifier);
+}
+
+static inline struct unicam_device *
+sd_to_unicam_device(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct unicam_device, subdev.sd);
+}
+
+static void unicam_release(struct kref *kref)
+{
+ struct unicam_device *unicam =
+ container_of(kref, struct unicam_device, kref);
+
+ if (unicam->mdev.dev)
+ media_device_cleanup(&unicam->mdev);
+
+ mutex_destroy(&unicam->lock);
+ kfree(unicam);
+}
+
+static struct unicam_device *unicam_get(struct unicam_device *unicam)
+{
+ kref_get(&unicam->kref);
+
+ return unicam;
+}
+
+static void unicam_put(struct unicam_device *unicam)
+{
+ kref_put(&unicam->kref, unicam_release);
+}
+
+/* -----------------------------------------------------------------------------
+ * Misc helper functions
+ */
+
+static inline bool unicam_sd_pad_is_source(u32 pad)
+{
+ /* Camera RX has 1 sink pad, and N source pads */
+ return pad != UNICAM_SD_PAD_SINK;
+}
+
+static inline bool is_metadata_node(struct unicam_node *node)
+{
+ return node->video_dev.device_caps & V4L2_CAP_META_CAPTURE;
+}
+
+static inline bool is_image_node(struct unicam_node *node)
+{
+ return node->video_dev.device_caps & V4L2_CAP_VIDEO_CAPTURE;
+}
+
+/* -----------------------------------------------------------------------------
+ * Format data table and helper functions
+ */
+
+static const struct v4l2_mbus_framefmt unicam_default_image_format = {
+ .width = 640,
+ .height = 480,
+ .code = MEDIA_BUS_FMT_UYVY8_1X16,
+ .field = V4L2_FIELD_NONE,
+ .colorspace = V4L2_COLORSPACE_SRGB,
+ .ycbcr_enc = V4L2_YCBCR_ENC_601,
+ .quantization = V4L2_QUANTIZATION_LIM_RANGE,
+ .xfer_func = V4L2_XFER_FUNC_SRGB,
+ .flags = 0,
+};
+
+static const struct v4l2_mbus_framefmt unicam_default_meta_format = {
+ .width = 640,
+ .height = 2,
+ .code = MEDIA_BUS_FMT_META_8,
+ .field = V4L2_FIELD_NONE,
+};
+
+static const struct unicam_format_info unicam_image_formats[] = {
+ /* YUV Formats */
+ {
+ .fourcc = V4L2_PIX_FMT_YUYV,
+ .code = MEDIA_BUS_FMT_YUYV8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ }, {
+ .fourcc = V4L2_PIX_FMT_UYVY,
+ .code = MEDIA_BUS_FMT_UYVY8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ }, {
+ .fourcc = V4L2_PIX_FMT_YVYU,
+ .code = MEDIA_BUS_FMT_YVYU8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ }, {
+ .fourcc = V4L2_PIX_FMT_VYUY,
+ .code = MEDIA_BUS_FMT_VYUY8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ }, {
+ /* RGB Formats */
+ .fourcc = V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */
+ .code = MEDIA_BUS_FMT_RGB565_1X16,
+ .depth = 16,
+ .csi_dt = 0x22,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB24, /* rgb */
+ .code = MEDIA_BUS_FMT_RGB888_1X24,
+ .depth = 24,
+ .csi_dt = 0x24,
+ }, {
+ .fourcc = V4L2_PIX_FMT_BGR24, /* bgr */
+ .code = MEDIA_BUS_FMT_BGR888_1X24,
+ .depth = 24,
+ .csi_dt = 0x24,
+ }, {
+ /* Bayer Formats */
+ .fourcc = V4L2_PIX_FMT_SBGGR8,
+ .code = MEDIA_BUS_FMT_SBGGR8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG8,
+ .code = MEDIA_BUS_FMT_SGBRG8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG8,
+ .code = MEDIA_BUS_FMT_SGRBG8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB8,
+ .code = MEDIA_BUS_FMT_SRGGB8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR10P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SBGGR10,
+ .code = MEDIA_BUS_FMT_SBGGR10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .unpack = UNICAM_PUM_UNPACK10,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG10P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGBRG10,
+ .code = MEDIA_BUS_FMT_SGBRG10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .unpack = UNICAM_PUM_UNPACK10,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG10P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGRBG10,
+ .code = MEDIA_BUS_FMT_SGRBG10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .unpack = UNICAM_PUM_UNPACK10,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB10P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SRGGB10,
+ .code = MEDIA_BUS_FMT_SRGGB10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .unpack = UNICAM_PUM_UNPACK10,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR12P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SBGGR12,
+ .code = MEDIA_BUS_FMT_SBGGR12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .unpack = UNICAM_PUM_UNPACK12,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG12P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGBRG12,
+ .code = MEDIA_BUS_FMT_SGBRG12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .unpack = UNICAM_PUM_UNPACK12,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG12P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGRBG12,
+ .code = MEDIA_BUS_FMT_SGRBG12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .unpack = UNICAM_PUM_UNPACK12,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB12P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SRGGB12,
+ .code = MEDIA_BUS_FMT_SRGGB12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .unpack = UNICAM_PUM_UNPACK12,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR14P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SBGGR14,
+ .code = MEDIA_BUS_FMT_SBGGR14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .unpack = UNICAM_PUM_UNPACK14,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG14P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGBRG14,
+ .code = MEDIA_BUS_FMT_SGBRG14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .unpack = UNICAM_PUM_UNPACK14,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG14P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SGRBG14,
+ .code = MEDIA_BUS_FMT_SGRBG14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .unpack = UNICAM_PUM_UNPACK14,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB14P,
+ .unpacked_fourcc = V4L2_PIX_FMT_SRGGB14,
+ .code = MEDIA_BUS_FMT_SRGGB14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .unpack = UNICAM_PUM_UNPACK14,
+ }, {
+ /* 16 bit Bayer formats could be supported. */
+
+ /* Greyscale formats */
+ .fourcc = V4L2_PIX_FMT_GREY,
+ .code = MEDIA_BUS_FMT_Y8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y10P,
+ .unpacked_fourcc = V4L2_PIX_FMT_Y10,
+ .code = MEDIA_BUS_FMT_Y10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .unpack = UNICAM_PUM_UNPACK10,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y12P,
+ .unpacked_fourcc = V4L2_PIX_FMT_Y12,
+ .code = MEDIA_BUS_FMT_Y12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .unpack = UNICAM_PUM_UNPACK12,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y14P,
+ .unpacked_fourcc = V4L2_PIX_FMT_Y14,
+ .code = MEDIA_BUS_FMT_Y14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .unpack = UNICAM_PUM_UNPACK14,
+ },
+};
+
+static const struct unicam_format_info unicam_meta_formats[] = {
+ {
+ .fourcc = V4L2_META_FMT_GENERIC_8,
+ .code = MEDIA_BUS_FMT_META_8,
+ .depth = 8,
+ }, {
+ .fourcc = V4L2_META_FMT_GENERIC_CSI2_10,
+ .code = MEDIA_BUS_FMT_META_10,
+ .depth = 10,
+ }, {
+ .fourcc = V4L2_META_FMT_GENERIC_CSI2_12,
+ .code = MEDIA_BUS_FMT_META_12,
+ .depth = 12,
+ }, {
+ .fourcc = V4L2_META_FMT_GENERIC_CSI2_14,
+ .code = MEDIA_BUS_FMT_META_14,
+ .depth = 14,
+ },
+};
+
+/* Format setup functions */
+static const struct unicam_format_info *
+unicam_find_format_by_code(u32 code, u32 pad)
+{
+ const struct unicam_format_info *formats;
+ unsigned int num_formats;
+ unsigned int i;
+
+ if (pad == UNICAM_SD_PAD_SOURCE_IMAGE) {
+ formats = unicam_image_formats;
+ num_formats = ARRAY_SIZE(unicam_image_formats);
+ } else {
+ formats = unicam_meta_formats;
+ num_formats = ARRAY_SIZE(unicam_meta_formats);
+ }
+
+ for (i = 0; i < num_formats; i++) {
+ if (formats[i].code == code)
+ return &formats[i];
+ }
+
+ return NULL;
+}
+
+static const struct unicam_format_info *
+unicam_find_format_by_fourcc(u32 fourcc, u32 pad)
+{
+ const struct unicam_format_info *formats;
+ unsigned int num_formats;
+ unsigned int i;
+
+ if (pad == UNICAM_SD_PAD_SOURCE_IMAGE) {
+ formats = unicam_image_formats;
+ num_formats = ARRAY_SIZE(unicam_image_formats);
+ } else {
+ formats = unicam_meta_formats;
+ num_formats = ARRAY_SIZE(unicam_meta_formats);
+ }
+
+ for (i = 0; i < num_formats; ++i) {
+ if (formats[i].fourcc == fourcc)
+ return &formats[i];
+ }
+
+ return NULL;
+}
+
+static void unicam_calc_image_size_bpl(struct unicam_device *unicam,
+ const struct unicam_format_info *fmtinfo,
+ struct v4l2_pix_format *pix)
+{
+ u32 min_bpl;
+
+ v4l_bound_align_image(&pix->width, UNICAM_IMAGE_MIN_WIDTH,
+ UNICAM_IMAGE_MAX_WIDTH, 2,
+ &pix->height, UNICAM_IMAGE_MIN_HEIGHT,
+ UNICAM_IMAGE_MAX_HEIGHT, 0, 0);
+
+ /* Unpacking always goes to 16bpp */
+ if (pix->pixelformat == fmtinfo->unpacked_fourcc)
+ min_bpl = pix->width * 2;
+ else
+ min_bpl = pix->width * fmtinfo->depth / 8;
+ min_bpl = ALIGN(min_bpl, UNICAM_IMAGE_BPL_ALIGNMENT);
+
+ pix->bytesperline = ALIGN(pix->bytesperline, UNICAM_IMAGE_BPL_ALIGNMENT);
+ pix->bytesperline = clamp_t(unsigned int, pix->bytesperline, min_bpl,
+ UNICAM_IMAGE_MAX_BPL);
+
+ pix->sizeimage = pix->height * pix->bytesperline;
+}
+
+static void unicam_calc_meta_size_bpl(struct unicam_device *unicam,
+ const struct unicam_format_info *fmtinfo,
+ struct v4l2_meta_format *meta)
+{
+ v4l_bound_align_image(&meta->width, UNICAM_META_MIN_WIDTH,
+ UNICAM_META_MAX_WIDTH, 0,
+ &meta->height, UNICAM_META_MIN_HEIGHT,
+ UNICAM_META_MAX_HEIGHT, 0, 0);
+
+ meta->bytesperline = ALIGN(meta->width * fmtinfo->depth / 8,
+ UNICAM_DMA_BPL_ALIGNMENT);
+ meta->buffersize = meta->height * meta->bytesperline;
+}
+
+/* -----------------------------------------------------------------------------
+ * Hardware handling
+ */
+
+static inline void unicam_clk_write(struct unicam_device *unicam, u32 val)
+{
+ /* Pass the CM_PASSWORD along with the value. */
+ writel(val | 0x5a000000, unicam->clk_gate_base);
+}
+
+static inline u32 unicam_reg_read(struct unicam_device *unicam, u32 offset)
+{
+ return readl(unicam->base + offset);
+}
+
+static inline void unicam_reg_write(struct unicam_device *unicam, u32 offset, u32 val)
+{
+ writel(val, unicam->base + offset);
+}
+
+static inline int unicam_get_field(u32 value, u32 mask)
+{
+ return (value & mask) >> __ffs(mask);
+}
+
+static inline void unicam_set_field(u32 *valp, u32 field, u32 mask)
+{
+ u32 val = *valp;
+
+ val &= ~mask;
+ val |= (field << __ffs(mask)) & mask;
+ *valp = val;
+}
+
+static inline void unicam_reg_write_field(struct unicam_device *unicam, u32 offset,
+ u32 field, u32 mask)
+{
+ u32 val = unicam_reg_read(unicam, offset);
+
+ unicam_set_field(&val, field, mask);
+ unicam_reg_write(unicam, offset, val);
+}
+
+static void unicam_wr_dma_addr(struct unicam_node *node,
+ struct unicam_buffer *buf)
+{
+ dma_addr_t endaddr = buf->dma_addr + buf->size;
+
+ if (node->id == UNICAM_IMAGE_NODE) {
+ unicam_reg_write(node->dev, UNICAM_IBSA0, buf->dma_addr);
+ unicam_reg_write(node->dev, UNICAM_IBEA0, endaddr);
+ } else {
+ unicam_reg_write(node->dev, UNICAM_DBSA0, buf->dma_addr);
+ unicam_reg_write(node->dev, UNICAM_DBEA0, endaddr);
+ }
+}
+
+static unsigned int unicam_get_lines_done(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_IMAGE_NODE];
+ unsigned int stride = node->fmt.fmt.pix.bytesperline;
+ struct unicam_buffer *frm = node->cur_frm;
+ dma_addr_t cur_addr;
+
+ if (!frm)
+ return 0;
+
+ cur_addr = unicam_reg_read(unicam, UNICAM_IBWP);
+ return (unsigned int)(cur_addr - frm->dma_addr) / stride;
+}
+
+static void unicam_schedule_next_buffer(struct unicam_node *node)
+{
+ struct unicam_buffer *buf;
+
+ buf = list_first_entry(&node->dma_queue, struct unicam_buffer, list);
+ node->next_frm = buf;
+ list_del(&buf->list);
+
+ unicam_wr_dma_addr(node, buf);
+}
+
+static void unicam_schedule_dummy_buffer(struct unicam_node *node)
+{
+ int node_id = is_image_node(node) ? UNICAM_IMAGE_NODE : UNICAM_METADATA_NODE;
+
+ dev_dbg(node->dev->dev, "Scheduling dummy buffer for node %d\n", node_id);
+
+ unicam_wr_dma_addr(node, &node->dummy_buf);
+
+ node->next_frm = NULL;
+}
+
+static void unicam_process_buffer_complete(struct unicam_node *node,
+ unsigned int sequence)
+{
+ node->cur_frm->vb.field = node->fmt.fmt.pix.field;
+ node->cur_frm->vb.sequence = sequence;
+
+ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE);
+}
+
+static void unicam_queue_event_sof(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_IMAGE_NODE];
+ struct v4l2_event event = {
+ .type = V4L2_EVENT_FRAME_SYNC,
+ .u.frame_sync.frame_sequence = unicam->sequence,
+ };
+
+ v4l2_event_queue(&node->video_dev, &event);
+}
+
+static irqreturn_t unicam_isr(int irq, void *dev)
+{
+ struct unicam_device *unicam = dev;
+ unsigned int lines_done = unicam_get_lines_done(dev);
+ unsigned int sequence = unicam->sequence;
+ unsigned int i;
+ u32 ista, sta;
+ bool fe;
+ u64 ts;
+
+ sta = unicam_reg_read(unicam, UNICAM_STA);
+ /* Write value back to clear the interrupts */
+ unicam_reg_write(unicam, UNICAM_STA, sta);
+
+ ista = unicam_reg_read(unicam, UNICAM_ISTA);
+ /* Write value back to clear the interrupts */
+ unicam_reg_write(unicam, UNICAM_ISTA, ista);
+
+ dev_dbg(unicam->dev, "ISR: ISTA: 0x%X, STA: 0x%X, sequence %d, lines done %d\n",
+ ista, sta, sequence, lines_done);
+
+ if (!(sta & (UNICAM_IS | UNICAM_PI0)))
+ return IRQ_HANDLED;
+
+ /*
+ * Look for either the Frame End interrupt or the Packet Capture status
+ * to signal a frame end.
+ */
+ fe = ista & UNICAM_FEI || sta & UNICAM_PI0;
+
+ /*
+ * We must run the frame end handler first. If we have a valid next_frm
+ * and we get a simultaneout FE + FS interrupt, running the FS handler
+ * first would null out the next_frm ptr and we would have lost the
+ * buffer forever.
+ */
+ if (fe) {
+ /*
+ * Ensure we have swapped buffers already as we can't
+ * stop the peripheral. If no buffer is available, use a
+ * dummy buffer to dump out frames until we get a new buffer
+ * to use.
+ */
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ /*
+ * If cur_frm == next_frm, it means we have not had
+ * a chance to swap buffers, likely due to having
+ * multiple interrupts occurring simultaneously (like FE
+ * + FS + LS). In this case, we cannot signal the buffer
+ * as complete, as the HW will reuse that buffer.
+ */
+ if (unicam->node[i].cur_frm &&
+ unicam->node[i].cur_frm != unicam->node[i].next_frm)
+ unicam_process_buffer_complete(&unicam->node[i],
+ sequence);
+ unicam->node[i].cur_frm = unicam->node[i].next_frm;
+ }
+ unicam->sequence++;
+ }
+
+ if (ista & UNICAM_FSI) {
+ /*
+ * Timestamp is to be when the first data byte was captured,
+ * aka frame start.
+ */
+ ts = ktime_get_ns();
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ if (unicam->node[i].cur_frm)
+ unicam->node[i].cur_frm->vb.vb2_buf.timestamp =
+ ts;
+ else
+ dev_dbg(unicam->v4l2_dev.dev,
+ "ISR: [%d] Dropping frame, buffer not available at FS\n",
+ i);
+ /*
+ * Set the next frame output to go to a dummy frame
+ * if we have not managed to obtain another frame
+ * from the queue.
+ */
+ unicam_schedule_dummy_buffer(&unicam->node[i]);
+ }
+
+ unicam_queue_event_sof(unicam);
+ }
+
+ /*
+ * Cannot swap buffer at frame end, there may be a race condition
+ * where the HW does not actually swap it if the new frame has
+ * already started.
+ */
+ if (ista & (UNICAM_FSI | UNICAM_LCI) && !fe) {
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ spin_lock(&unicam->node[i].dma_queue_lock);
+ if (!list_empty(&unicam->node[i].dma_queue) &&
+ !unicam->node[i].next_frm)
+ unicam_schedule_next_buffer(&unicam->node[i]);
+ spin_unlock(&unicam->node[i].dma_queue_lock);
+ }
+ }
+
+ if (unicam_reg_read(unicam, UNICAM_ICTL) & UNICAM_FCM) {
+ /* Switch out of trigger mode if selected */
+ unicam_reg_write_field(unicam, UNICAM_ICTL, 1, UNICAM_TFC);
+ unicam_reg_write_field(unicam, UNICAM_ICTL, 0, UNICAM_FCM);
+ }
+ return IRQ_HANDLED;
+}
+
+static void unicam_set_packing_config(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_IMAGE_NODE];
+ u32 pack, unpack;
+ u32 val;
+
+ if (node->fmt.fmt.pix.pixelformat == node->fmtinfo->fourcc) {
+ unpack = UNICAM_PUM_NONE;
+ pack = UNICAM_PPM_NONE;
+ } else {
+ unpack = node->fmtinfo->unpack;
+ /* Repacking is always to 16bpp */
+ pack = UNICAM_PPM_PACK16;
+ }
+
+ val = 0;
+ unicam_set_field(&val, unpack, UNICAM_PUM_MASK);
+ unicam_set_field(&val, pack, UNICAM_PPM_MASK);
+ unicam_reg_write(unicam, UNICAM_IPIPE, val);
+}
+
+static void unicam_cfg_image_id(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_IMAGE_NODE];
+
+ if (unicam->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 mode, hardcode VC 0 for now. */
+ unicam_reg_write(unicam, UNICAM_IDI0,
+ (0 << 6) | node->fmtinfo->csi_dt);
+ } else {
+ /* CCP2 mode */
+ unicam_reg_write(unicam, UNICAM_IDI0,
+ 0x80 | node->fmtinfo->csi_dt);
+ }
+}
+
+static void unicam_enable_ed(struct unicam_device *unicam)
+{
+ u32 val = unicam_reg_read(unicam, UNICAM_DCS);
+
+ unicam_set_field(&val, 2, UNICAM_EDL_MASK);
+ /* Do not wrap at the end of the embedded data buffer */
+ unicam_set_field(&val, 0, UNICAM_DBOB);
+
+ unicam_reg_write(unicam, UNICAM_DCS, val);
+}
+
+static void unicam_start_rx(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_IMAGE_NODE];
+ int line_int_freq = node->fmt.fmt.pix.height >> 2;
+ u32 val;
+
+ line_int_freq = max(line_int_freq, 128);
+
+ /*
+ * Enable lane clocks. The register is structured as follows:
+ *
+ * [9:8] - DAT3
+ * [7:6] - DAT2
+ * [5:4] - DAT1
+ * [3:2] - DAT0
+ * [1:0] - CLK
+ *
+ * Enabled lane must be set to b01, and disabled lanes to b00. The clock
+ * lane is always enabled.
+ */
+ val = 0x155 & GENMASK(unicam->pipe.num_data_lanes * 2 + 1, 0);
+ unicam_clk_write(unicam, val);
+
+ /* Basic init */
+ unicam_reg_write(unicam, UNICAM_CTRL, UNICAM_MEM);
+
+ /* Enable analogue control, and leave in reset. */
+ val = UNICAM_AR;
+ unicam_set_field(&val, 7, UNICAM_CTATADJ_MASK);
+ unicam_set_field(&val, 7, UNICAM_PTATADJ_MASK);
+ unicam_reg_write(unicam, UNICAM_ANA, val);
+ usleep_range(1000, 2000);
+
+ /* Come out of reset */
+ unicam_reg_write_field(unicam, UNICAM_ANA, 0, UNICAM_AR);
+
+ /* Peripheral reset */
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 1, UNICAM_CPR);
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 0, UNICAM_CPR);
+
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 0, UNICAM_CPE);
+
+ /* Enable Rx control. */
+ val = unicam_reg_read(unicam, UNICAM_CTRL);
+ if (unicam->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ unicam_set_field(&val, UNICAM_CPM_CSI2, UNICAM_CPM_MASK);
+ unicam_set_field(&val, UNICAM_DCM_STROBE, UNICAM_DCM_MASK);
+ } else {
+ unicam_set_field(&val, UNICAM_CPM_CCP2, UNICAM_CPM_MASK);
+ unicam_set_field(&val, unicam->bus_flags, UNICAM_DCM_MASK);
+ }
+ /* Packet framer timeout */
+ unicam_set_field(&val, 0xf, UNICAM_PFT_MASK);
+ unicam_set_field(&val, 128, UNICAM_OET_MASK);
+ unicam_reg_write(unicam, UNICAM_CTRL, val);
+
+ unicam_reg_write(unicam, UNICAM_IHWIN, 0);
+ unicam_reg_write(unicam, UNICAM_IVWIN, 0);
+
+ /* AXI bus access QoS setup */
+ val = unicam_reg_read(unicam, UNICAM_PRI);
+ unicam_set_field(&val, 0, UNICAM_BL_MASK);
+ unicam_set_field(&val, 0, UNICAM_BS_MASK);
+ unicam_set_field(&val, 0xe, UNICAM_PP_MASK);
+ unicam_set_field(&val, 8, UNICAM_NP_MASK);
+ unicam_set_field(&val, 2, UNICAM_PT_MASK);
+ unicam_set_field(&val, 1, UNICAM_PE);
+ unicam_reg_write(unicam, UNICAM_PRI, val);
+
+ unicam_reg_write_field(unicam, UNICAM_ANA, 0, UNICAM_DDL);
+
+ /* Always start in trigger frame capture mode (UNICAM_FCM set) */
+ val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM | UNICAM_IBOB;
+ unicam_set_field(&val, line_int_freq, UNICAM_LCIE_MASK);
+ unicam_reg_write(unicam, UNICAM_ICTL, val);
+ unicam_reg_write(unicam, UNICAM_STA, UNICAM_STA_MASK_ALL);
+ unicam_reg_write(unicam, UNICAM_ISTA, UNICAM_ISTA_MASK_ALL);
+
+ /* tclk_term_en */
+ unicam_reg_write_field(unicam, UNICAM_CLT, 2, UNICAM_CLT1_MASK);
+ /* tclk_settle */
+ unicam_reg_write_field(unicam, UNICAM_CLT, 6, UNICAM_CLT2_MASK);
+ /* td_term_en */
+ unicam_reg_write_field(unicam, UNICAM_DLT, 2, UNICAM_DLT1_MASK);
+ /* ths_settle */
+ unicam_reg_write_field(unicam, UNICAM_DLT, 6, UNICAM_DLT2_MASK);
+ /* trx_enable */
+ unicam_reg_write_field(unicam, UNICAM_DLT, 0, UNICAM_DLT3_MASK);
+
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 0, UNICAM_SOE);
+
+ /* Packet compare setup - required to avoid missing frame ends */
+ val = 0;
+ unicam_set_field(&val, 1, UNICAM_PCE);
+ unicam_set_field(&val, 1, UNICAM_GI);
+ unicam_set_field(&val, 1, UNICAM_CPH);
+ unicam_set_field(&val, 0, UNICAM_PCVC_MASK);
+ unicam_set_field(&val, 1, UNICAM_PCDT_MASK);
+ unicam_reg_write(unicam, UNICAM_CMP0, val);
+
+ /* Enable clock lane and set up terminations */
+ val = 0;
+ if (unicam->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 */
+ unicam_set_field(&val, 1, UNICAM_CLE);
+ unicam_set_field(&val, 1, UNICAM_CLLPE);
+ if (!(unicam->bus_flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK)) {
+ unicam_set_field(&val, 1, UNICAM_CLTRE);
+ unicam_set_field(&val, 1, UNICAM_CLHSE);
+ }
+ } else {
+ /* CCP2 */
+ unicam_set_field(&val, 1, UNICAM_CLE);
+ unicam_set_field(&val, 1, UNICAM_CLHSE);
+ unicam_set_field(&val, 1, UNICAM_CLTRE);
+ }
+ unicam_reg_write(unicam, UNICAM_CLK, val);
+
+ /*
+ * Enable required data lanes with appropriate terminations.
+ * The same value needs to be written to UNICAM_DATn registers for
+ * the active lanes, and 0 for inactive ones.
+ */
+ val = 0;
+ if (unicam->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 */
+ unicam_set_field(&val, 1, UNICAM_DLE);
+ unicam_set_field(&val, 1, UNICAM_DLLPE);
+ if (!(unicam->bus_flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK)) {
+ unicam_set_field(&val, 1, UNICAM_DLTRE);
+ unicam_set_field(&val, 1, UNICAM_DLHSE);
+ }
+ } else {
+ /* CCP2 */
+ unicam_set_field(&val, 1, UNICAM_DLE);
+ unicam_set_field(&val, 1, UNICAM_DLHSE);
+ unicam_set_field(&val, 1, UNICAM_DLTRE);
+ }
+ unicam_reg_write(unicam, UNICAM_DAT0, val);
+
+ if (unicam->pipe.num_data_lanes == 1)
+ val = 0;
+ unicam_reg_write(unicam, UNICAM_DAT1, val);
+
+ if (unicam->max_data_lanes > 2) {
+ /*
+ * Registers UNICAM_DAT2 and UNICAM_DAT3 only valid if the
+ * instance supports more than 2 data lanes.
+ */
+ if (unicam->pipe.num_data_lanes == 2)
+ val = 0;
+ unicam_reg_write(unicam, UNICAM_DAT2, val);
+
+ if (unicam->pipe.num_data_lanes == 3)
+ val = 0;
+ unicam_reg_write(unicam, UNICAM_DAT3, val);
+ }
+
+ unicam_reg_write(unicam, UNICAM_IBLS,
+ node->fmt.fmt.pix.bytesperline);
+ unicam_wr_dma_addr(node, node->cur_frm);
+ unicam_set_packing_config(unicam);
+ unicam_cfg_image_id(unicam);
+
+ val = unicam_reg_read(unicam, UNICAM_MISC);
+ unicam_set_field(&val, 1, UNICAM_FL0);
+ unicam_set_field(&val, 1, UNICAM_FL1);
+ unicam_reg_write(unicam, UNICAM_MISC, val);
+
+ /* Enable peripheral */
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 1, UNICAM_CPE);
+
+ /* Load image pointers */
+ unicam_reg_write_field(unicam, UNICAM_ICTL, 1, UNICAM_LIP_MASK);
+
+ /*
+ * Enable trigger only for the first frame to
+ * sync correctly to the FS from the source.
+ */
+ unicam_reg_write_field(unicam, UNICAM_ICTL, 1, UNICAM_TFC);
+}
+
+static void unicam_start_metadata(struct unicam_device *unicam)
+{
+ struct unicam_node *node = &unicam->node[UNICAM_METADATA_NODE];
+
+ unicam_enable_ed(unicam);
+ unicam_wr_dma_addr(node, node->cur_frm);
+ unicam_reg_write_field(unicam, UNICAM_DCS, 1, UNICAM_LDP);
+}
+
+static void unicam_disable(struct unicam_device *unicam)
+{
+ /* Analogue lane control disable */
+ unicam_reg_write_field(unicam, UNICAM_ANA, 1, UNICAM_DDL);
+
+ /* Stop the output engine */
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 1, UNICAM_SOE);
+
+ /* Disable the data lanes. */
+ unicam_reg_write(unicam, UNICAM_DAT0, 0);
+ unicam_reg_write(unicam, UNICAM_DAT1, 0);
+
+ if (unicam->max_data_lanes > 2) {
+ unicam_reg_write(unicam, UNICAM_DAT2, 0);
+ unicam_reg_write(unicam, UNICAM_DAT3, 0);
+ }
+
+ /* Peripheral reset */
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 1, UNICAM_CPR);
+ usleep_range(50, 100);
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 0, UNICAM_CPR);
+
+ /* Disable peripheral */
+ unicam_reg_write_field(unicam, UNICAM_CTRL, 0, UNICAM_CPE);
+
+ /* Clear ED setup */
+ unicam_reg_write(unicam, UNICAM_DCS, 0);
+
+ /* Disable all lane clocks */
+ unicam_clk_write(unicam, 0);
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 subdev operations
+ */
+
+static int __unicam_subdev_set_routing(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_krouting *routing)
+{
+ struct v4l2_subdev_route *route;
+ int ret;
+
+ ret = v4l2_subdev_routing_validate(sd, routing,
+ V4L2_SUBDEV_ROUTING_ONLY_1_TO_1);
+ if (ret)
+ return ret;
+
+ ret = v4l2_subdev_set_routing(sd, state, routing);
+ if (ret)
+ return ret;
+
+ for_each_active_route(&state->routing, route) {
+ const struct v4l2_mbus_framefmt *def_fmt;
+ struct v4l2_mbus_framefmt *fmt;
+
+ if (route->source_pad == UNICAM_SD_PAD_SOURCE_IMAGE)
+ def_fmt = &unicam_default_image_format;
+ else
+ def_fmt = &unicam_default_meta_format;
+
+ fmt = v4l2_subdev_state_get_format(state, route->sink_pad,
+ route->sink_stream);
+ *fmt = *def_fmt;
+ fmt = v4l2_subdev_state_get_format(state, route->source_pad,
+ route->source_stream);
+ *fmt = *def_fmt;
+ }
+
+ return 0;
+}
+
+static int unicam_subdev_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_subdev_route routes[] = {
+ {
+ .sink_pad = UNICAM_SD_PAD_SINK,
+ .sink_stream = 0,
+ .source_pad = UNICAM_SD_PAD_SOURCE_IMAGE,
+ .source_stream = 0,
+ .flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE,
+ },
+ };
+
+ struct v4l2_subdev_krouting routing = {
+ .len_routes = ARRAY_SIZE(routes),
+ .num_routes = ARRAY_SIZE(routes),
+ .routes = routes,
+ };
+
+ /* Initialize routing to single route to the fist source pad. */
+ return __unicam_subdev_set_routing(sd, state, &routing);
+}
+
+static int unicam_subdev_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ u32 pad, stream;
+ int ret;
+
+ ret = v4l2_subdev_routing_find_opposite_end(&state->routing,
+ code->pad, code->stream,
+ &pad, &stream);
+ if (ret)
+ return ret;
+
+ if (unicam_sd_pad_is_source(code->pad)) {
+ /* No transcoding, source and sink codes must match. */
+ const struct v4l2_mbus_framefmt *fmt;
+
+ fmt = v4l2_subdev_state_get_format(state, pad, stream);
+ if (!fmt)
+ return -EINVAL;
+
+ if (code->index > 0)
+ return -EINVAL;
+
+ code->code = fmt->code;
+ } else {
+ const struct unicam_format_info *formats;
+ unsigned int num_formats;
+
+ if (pad == UNICAM_SD_PAD_SOURCE_IMAGE) {
+ formats = unicam_image_formats;
+ num_formats = ARRAY_SIZE(unicam_image_formats);
+ } else {
+ formats = unicam_meta_formats;
+ num_formats = ARRAY_SIZE(unicam_meta_formats);
+ }
+
+ if (code->index >= num_formats)
+ return -EINVAL;
+
+ code->code = formats[code->index].code;
+ }
+
+ return 0;
+}
+
+static int unicam_subdev_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ u32 pad, stream;
+ int ret;
+
+ if (fse->index > 0)
+ return -EINVAL;
+
+ ret = v4l2_subdev_routing_find_opposite_end(&state->routing, fse->pad,
+ fse->stream, &pad,
+ &stream);
+ if (ret)
+ return ret;
+
+ if (unicam_sd_pad_is_source(fse->pad)) {
+ /* No transcoding, source and sink formats must match. */
+ const struct v4l2_mbus_framefmt *fmt;
+
+ fmt = v4l2_subdev_state_get_format(state, pad, stream);
+ if (!fmt)
+ return -EINVAL;
+
+ if (fse->code != fmt->code)
+ return -EINVAL;
+
+ fse->min_width = fmt->width;
+ fse->max_width = fmt->width;
+ fse->min_height = fmt->height;
+ fse->max_height = fmt->height;
+ } else {
+ const struct unicam_format_info *fmtinfo;
+
+ fmtinfo = unicam_find_format_by_code(fse->code, pad);
+ if (!fmtinfo)
+ return -EINVAL;
+
+ if (pad == UNICAM_SD_PAD_SOURCE_IMAGE) {
+ fse->min_width = UNICAM_IMAGE_MIN_WIDTH;
+ fse->max_width = UNICAM_IMAGE_MAX_WIDTH;
+ fse->min_height = UNICAM_IMAGE_MIN_HEIGHT;
+ fse->max_height = UNICAM_IMAGE_MAX_HEIGHT;
+ } else {
+ fse->min_width = UNICAM_META_MIN_WIDTH;
+ fse->max_width = UNICAM_META_MAX_WIDTH;
+ fse->min_height = UNICAM_META_MIN_HEIGHT;
+ fse->max_height = UNICAM_META_MAX_HEIGHT;
+ }
+ }
+
+ return 0;
+}
+
+static int unicam_subdev_set_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_format *format)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+ struct v4l2_mbus_framefmt *sink_format, *source_format;
+ const struct unicam_format_info *fmtinfo;
+ u32 source_pad, source_stream;
+ int ret;
+
+ if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE &&
+ unicam->subdev.enabled_streams)
+ return -EBUSY;
+
+ /* No transcoding, source and sink formats must match. */
+ if (unicam_sd_pad_is_source(format->pad))
+ return v4l2_subdev_get_fmt(sd, state, format);
+
+ /*
+ * Allowed formats for the stream on the sink pad depend on what source
+ * pad the stream is routed to. Find the corresponding source pad and
+ * use it to validate the media bus code.
+ */
+ ret = v4l2_subdev_routing_find_opposite_end(&state->routing,
+ format->pad, format->stream,
+ &source_pad, &source_stream);
+ if (ret)
+ return ret;
+
+ fmtinfo = unicam_find_format_by_code(format->format.code, source_pad);
+ if (!fmtinfo) {
+ fmtinfo = source_pad == UNICAM_SD_PAD_SOURCE_IMAGE
+ ? &unicam_image_formats[0] : &unicam_meta_formats[0];
+ format->format.code = fmtinfo->code;
+ }
+
+ if (source_pad == UNICAM_SD_PAD_SOURCE_IMAGE) {
+ format->format.width = clamp_t(unsigned int,
+ format->format.width,
+ UNICAM_IMAGE_MIN_WIDTH,
+ UNICAM_IMAGE_MAX_WIDTH);
+ format->format.height = clamp_t(unsigned int,
+ format->format.height,
+ UNICAM_IMAGE_MIN_HEIGHT,
+ UNICAM_IMAGE_MAX_HEIGHT);
+ format->format.field = V4L2_FIELD_NONE;
+ } else {
+ format->format.width = clamp_t(unsigned int,
+ format->format.width,
+ UNICAM_META_MIN_WIDTH,
+ UNICAM_META_MAX_WIDTH);
+ format->format.height = clamp_t(unsigned int,
+ format->format.height,
+ UNICAM_META_MIN_HEIGHT,
+ UNICAM_META_MAX_HEIGHT);
+ format->format.field = V4L2_FIELD_NONE;
+
+ /* Colorspace don't apply to metadata. */
+ format->format.colorspace = 0;
+ format->format.ycbcr_enc = 0;
+ format->format.quantization = 0;
+ format->format.xfer_func = 0;
+ }
+
+ sink_format = v4l2_subdev_state_get_format(state, format->pad,
+ format->stream);
+ source_format = v4l2_subdev_state_get_format(state, source_pad,
+ source_stream);
+ *sink_format = format->format;
+ *source_format = format->format;
+
+ return 0;
+}
+
+static int unicam_subdev_set_routing(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ enum v4l2_subdev_format_whence which,
+ struct v4l2_subdev_krouting *routing)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+
+ if (which == V4L2_SUBDEV_FORMAT_ACTIVE && unicam->subdev.enabled_streams)
+ return -EBUSY;
+
+ return __unicam_subdev_set_routing(sd, state, routing);
+}
+
+static int unicam_sd_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+ u32 other_pad, other_stream;
+ int ret;
+
+ ret = v4l2_subdev_routing_find_opposite_end(&state->routing, pad, 0,
+ &other_pad, &other_stream);
+ if (ret)
+ return ret;
+
+ ret = v4l2_subdev_enable_streams(unicam->sensor.subdev,
+ unicam->sensor.pad->index,
+ BIT(other_stream));
+ if (ret) {
+ dev_err(unicam->dev, "stream on failed in subdev\n");
+ return ret;
+ }
+
+ unicam->subdev.enabled_streams |= BIT(other_stream);
+
+ return 0;
+}
+
+static int unicam_sd_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+ u32 other_pad, other_stream;
+ int ret;
+
+ ret = v4l2_subdev_routing_find_opposite_end(&state->routing, pad, 0,
+ &other_pad, &other_stream);
+ if (ret)
+ return ret;
+
+ v4l2_subdev_disable_streams(unicam->sensor.subdev,
+ unicam->sensor.pad->index,
+ BIT(other_stream));
+
+ unicam->subdev.enabled_streams &= ~BIT(other_stream);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_pad_ops unicam_subdev_pad_ops = {
+ .enum_mbus_code = unicam_subdev_enum_mbus_code,
+ .enum_frame_size = unicam_subdev_enum_frame_size,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = unicam_subdev_set_format,
+ .set_routing = unicam_subdev_set_routing,
+ .enable_streams = unicam_sd_enable_streams,
+ .disable_streams = unicam_sd_disable_streams,
+};
+
+static const struct v4l2_subdev_ops unicam_subdev_ops = {
+ .pad = &unicam_subdev_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops unicam_subdev_internal_ops = {
+ .init_state = unicam_subdev_init_state,
+};
+
+static const struct media_entity_operations unicam_subdev_media_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+ .has_pad_interdep = v4l2_subdev_has_pad_interdep,
+};
+
+static int unicam_subdev_init(struct unicam_device *unicam)
+{
+ struct v4l2_subdev *sd = &unicam->subdev.sd;
+ int ret;
+
+ v4l2_subdev_init(sd, &unicam_subdev_ops);
+ sd->internal_ops = &unicam_subdev_internal_ops;
+ v4l2_set_subdevdata(sd, unicam);
+
+ sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+ sd->entity.ops = &unicam_subdev_media_ops;
+ sd->dev = unicam->dev;
+ sd->owner = THIS_MODULE;
+ sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_STREAMS;
+
+ strscpy(sd->name, "unicam", sizeof(sd->name));
+
+ unicam->subdev.pads[UNICAM_SD_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+ unicam->subdev.pads[UNICAM_SD_PAD_SOURCE_IMAGE].flags = MEDIA_PAD_FL_SOURCE;
+ unicam->subdev.pads[UNICAM_SD_PAD_SOURCE_METADATA].flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&sd->entity, ARRAY_SIZE(unicam->subdev.pads),
+ unicam->subdev.pads);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to initialize media entity: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = v4l2_subdev_init_finalize(sd);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to initialize subdev: %d\n", ret);
+ goto err_entity;
+ }
+
+ ret = v4l2_device_register_subdev(&unicam->v4l2_dev, sd);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to register subdev: %d\n", ret);
+ goto err_subdev;
+ }
+
+ return 0;
+
+err_subdev:
+ v4l2_subdev_cleanup(sd);
+err_entity:
+ media_entity_cleanup(&sd->entity);
+ return ret;
+}
+
+static void unicam_subdev_cleanup(struct unicam_device *unicam)
+{
+ v4l2_subdev_cleanup(&unicam->subdev.sd);
+ media_entity_cleanup(&unicam->subdev.sd.entity);
+}
+
+/* -----------------------------------------------------------------------------
+ * Videobuf2 queue operations
+ */
+
+static int unicam_queue_setup(struct vb2_queue *vq, unsigned int *nbuffers,
+ unsigned int *nplanes, unsigned int sizes[],
+ struct device *alloc_devs[])
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ u32 size = is_image_node(node) ? node->fmt.fmt.pix.sizeimage
+ : node->fmt.fmt.meta.buffersize;
+
+ if (*nplanes) {
+ if (sizes[0] < size) {
+ dev_dbg(node->dev->dev, "sizes[0] %i < size %u\n",
+ sizes[0], size);
+ return -EINVAL;
+ }
+ size = sizes[0];
+ }
+
+ *nplanes = 1;
+ sizes[0] = size;
+
+ return 0;
+}
+
+static int unicam_buffer_prepare(struct vb2_buffer *vb)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue);
+ struct unicam_buffer *buf = to_unicam_buffer(vb);
+ u32 size = is_image_node(node) ? node->fmt.fmt.pix.sizeimage
+ : node->fmt.fmt.meta.buffersize;
+
+ if (vb2_plane_size(vb, 0) < size) {
+ dev_dbg(node->dev->dev,
+ "data will not fit into plane (%lu < %u)\n",
+ vb2_plane_size(vb, 0), size);
+ return -EINVAL;
+ }
+
+ buf->dma_addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0);
+ buf->size = size;
+
+ vb2_set_plane_payload(&buf->vb.vb2_buf, 0, size);
+
+ return 0;
+}
+
+static void unicam_return_buffers(struct unicam_node *node,
+ enum vb2_buffer_state state)
+{
+ struct unicam_buffer *buf, *tmp;
+
+ list_for_each_entry_safe(buf, tmp, &node->dma_queue, list) {
+ list_del(&buf->list);
+ vb2_buffer_done(&buf->vb.vb2_buf, state);
+ }
+
+ if (node->cur_frm)
+ vb2_buffer_done(&node->cur_frm->vb.vb2_buf,
+ state);
+ if (node->next_frm && node->cur_frm != node->next_frm)
+ vb2_buffer_done(&node->next_frm->vb.vb2_buf,
+ state);
+
+ node->cur_frm = NULL;
+ node->next_frm = NULL;
+}
+
+static int unicam_num_data_lanes(struct unicam_device *unicam)
+{
+ struct v4l2_mbus_config mbus_config = { 0 };
+ unsigned int num_data_lanes;
+ int ret;
+
+ if (unicam->bus_type != V4L2_MBUS_CSI2_DPHY)
+ return unicam->max_data_lanes;
+
+ ret = v4l2_subdev_call(unicam->sensor.subdev, pad, get_mbus_config,
+ unicam->sensor.pad->index, &mbus_config);
+ if (ret == -ENOIOCTLCMD)
+ return unicam->max_data_lanes;
+
+ if (ret < 0) {
+ dev_err(unicam->dev, "Failed to get mbus config: %d\n", ret);
+ return ret;
+ }
+
+ num_data_lanes = mbus_config.bus.mipi_csi2.num_data_lanes;
+
+ if (num_data_lanes != 1 && num_data_lanes != 2 && num_data_lanes != 4) {
+ dev_err(unicam->dev,
+ "Device %s has requested %u data lanes, invalid\n",
+ unicam->sensor.subdev->name, num_data_lanes);
+ return -EINVAL;
+ }
+
+ if (num_data_lanes > unicam->max_data_lanes) {
+ dev_err(unicam->dev,
+ "Device %s has requested %u data lanes, >%u configured in DT\n",
+ unicam->sensor.subdev->name, num_data_lanes,
+ unicam->max_data_lanes);
+ return -EINVAL;
+ }
+
+ return num_data_lanes;
+}
+
+static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ struct unicam_device *unicam = node->dev;
+ struct unicam_buffer *buf;
+ struct media_pipeline_pad_iter iter;
+ struct media_pad *pad;
+ unsigned long flags;
+ int ret;
+
+ dev_dbg(unicam->dev, "Starting stream on %s device\n",
+ is_metadata_node(node) ? "metadata" : "image");
+
+ /*
+ * Start the pipeline. This validates all links, and populates the
+ * pipeline structure.
+ */
+ ret = video_device_pipeline_start(&node->video_dev, &unicam->pipe.pipe);
+ if (ret < 0) {
+ dev_dbg(unicam->dev, "Failed to start media pipeline: %d\n", ret);
+ goto err_buffers;
+ }
+
+ /*
+ * Determine which video nodes are included in the pipeline, and get the
+ * number of data lanes.
+ */
+ if (unicam->pipe.pipe.start_count == 1) {
+ unicam->pipe.nodes = 0;
+
+ media_pipeline_for_each_pad(&unicam->pipe.pipe, &iter, pad) {
+ if (pad->entity != &unicam->subdev.sd.entity)
+ continue;
+
+ if (pad->index == UNICAM_SD_PAD_SOURCE_IMAGE)
+ unicam->pipe.nodes |= BIT(UNICAM_IMAGE_NODE);
+ else if (pad->index == UNICAM_SD_PAD_SOURCE_METADATA)
+ unicam->pipe.nodes |= BIT(UNICAM_METADATA_NODE);
+ }
+
+ if (!(unicam->pipe.nodes & BIT(UNICAM_IMAGE_NODE))) {
+ dev_dbg(unicam->dev,
+ "Pipeline does not include image node\n");
+ ret = -EPIPE;
+ goto err_pipeline;
+ }
+
+ ret = unicam_num_data_lanes(unicam);
+ if (ret < 0)
+ goto err_pipeline;
+
+ unicam->pipe.num_data_lanes = ret;
+
+ dev_dbg(unicam->dev, "Running with %u data lanes, nodes %u\n",
+ unicam->pipe.num_data_lanes, unicam->pipe.nodes);
+ }
+
+ node->streaming = true;
+
+ /* Arm the node with the first buffer from the DMA queue. */
+ spin_lock_irqsave(&node->dma_queue_lock, flags);
+ buf = list_first_entry(&node->dma_queue, struct unicam_buffer, list);
+ node->cur_frm = buf;
+ node->next_frm = buf;
+ list_del(&buf->list);
+ spin_unlock_irqrestore(&node->dma_queue_lock, flags);
+
+ /*
+ * Wait for all the video devices in the pipeline to have been started
+ * before starting the hardware. In the general case, this would
+ * prevent capturing multiple streams independently. However, the
+ * Unicam DMA engines are not generic, they have been designed to
+ * capture image data and embedded data from the same camera sensor.
+ * Not only does the main use case not benefit from independent
+ * capture, it requires proper synchronization of the streams at start
+ * time.
+ */
+ if (unicam->pipe.pipe.start_count < hweight32(unicam->pipe.nodes))
+ return 0;
+
+ /* Configure and start Unicam. */
+ ret = pm_runtime_resume_and_get(unicam->dev);
+ if (ret < 0) {
+ dev_err(unicam->dev, "PM runtime resume failed: %d\n", ret);
+ goto err_pipeline;
+ }
+
+ unicam->sequence = 0;
+
+ if (unicam->pipe.nodes & BIT(UNICAM_METADATA_NODE))
+ unicam_start_metadata(unicam);
+
+ unicam_start_rx(unicam);
+
+ /* Enable the streams on the source. */
+ ret = v4l2_subdev_enable_streams(&unicam->subdev.sd,
+ UNICAM_SD_PAD_SOURCE_IMAGE,
+ BIT(0));
+ if (ret < 0) {
+ dev_err(unicam->dev, "stream on failed in subdev\n");
+ goto err_pm_put;
+ }
+
+ if (unicam->pipe.nodes & BIT(UNICAM_METADATA_NODE)) {
+ ret = v4l2_subdev_enable_streams(&unicam->subdev.sd,
+ UNICAM_SD_PAD_SOURCE_METADATA,
+ BIT(0));
+ if (ret < 0) {
+ dev_err(unicam->dev, "stream on failed in subdev\n");
+ goto err_pm_put;
+ }
+ }
+
+ return 0;
+
+err_pm_put:
+ pm_runtime_put_sync(unicam->dev);
+err_pipeline:
+ video_device_pipeline_stop(&node->video_dev);
+err_buffers:
+ unicam_return_buffers(node, VB2_BUF_STATE_QUEUED);
+ node->streaming = false;
+ return ret;
+}
+
+static void unicam_stop_streaming(struct vb2_queue *vq)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ struct unicam_device *unicam = node->dev;
+
+ /* Stop the hardware when the first video device gets stopped. */
+ if (unicam->pipe.pipe.start_count == hweight32(unicam->pipe.nodes)) {
+ if (unicam->pipe.nodes & BIT(UNICAM_METADATA_NODE))
+ v4l2_subdev_disable_streams(&unicam->subdev.sd,
+ UNICAM_SD_PAD_SOURCE_METADATA,
+ BIT(0));
+
+ v4l2_subdev_disable_streams(&unicam->subdev.sd,
+ UNICAM_SD_PAD_SOURCE_IMAGE,
+ BIT(0));
+
+ unicam_disable(unicam);
+
+ pm_runtime_put(unicam->dev);
+ }
+
+ node->streaming = false;
+
+ video_device_pipeline_stop(&node->video_dev);
+
+ /* Clear all queued buffers for the node */
+ unicam_return_buffers(node, VB2_BUF_STATE_ERROR);
+}
+
+static void unicam_buffer_queue(struct vb2_buffer *vb)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue);
+ struct unicam_buffer *buf = to_unicam_buffer(vb);
+
+ spin_lock_irq(&node->dma_queue_lock);
+ list_add_tail(&buf->list, &node->dma_queue);
+ spin_unlock_irq(&node->dma_queue_lock);
+}
+
+static const struct vb2_ops unicam_video_qops = {
+ .queue_setup = unicam_queue_setup,
+ .wait_prepare = vb2_ops_wait_prepare,
+ .wait_finish = vb2_ops_wait_finish,
+ .buf_prepare = unicam_buffer_prepare,
+ .start_streaming = unicam_start_streaming,
+ .stop_streaming = unicam_stop_streaming,
+ .buf_queue = unicam_buffer_queue,
+};
+
+/* -----------------------------------------------------------------------------
+ * V4L2 video device operations
+ */
+
+static int unicam_querycap(struct file *file, void *priv,
+ struct v4l2_capability *cap)
+{
+ strscpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver));
+ strscpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card));
+
+ cap->capabilities |= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_META_CAPTURE;
+
+ return 0;
+}
+
+static int unicam_enum_fmt_vid(struct file *file, void *priv,
+ struct v4l2_fmtdesc *f)
+{
+ unsigned int index;
+ unsigned int i;
+
+ for (i = 0, index = 0; i < ARRAY_SIZE(unicam_image_formats); i++) {
+ if (f->mbus_code && unicam_image_formats[i].code != f->mbus_code)
+ continue;
+
+ if (index == f->index) {
+ f->pixelformat = unicam_image_formats[i].fourcc;
+ return 0;
+ }
+
+ index++;
+
+ if (!unicam_image_formats[i].unpacked_fourcc)
+ continue;
+
+ if (index == f->index) {
+ f->pixelformat = unicam_image_formats[i].unpacked_fourcc;
+ return 0;
+ }
+
+ index++;
+ }
+
+ return -EINVAL;
+}
+
+static int unicam_g_fmt_vid(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ *f = node->fmt;
+
+ return 0;
+}
+
+static const struct unicam_format_info *
+__unicam_try_fmt_vid(struct unicam_node *node, struct v4l2_pix_format *pix)
+{
+ const struct unicam_format_info *fmtinfo;
+
+ /*
+ * Default to the first format if the requested pixel format code isn't
+ * supported.
+ */
+ fmtinfo = unicam_find_format_by_fourcc(pix->pixelformat,
+ UNICAM_SD_PAD_SOURCE_IMAGE);
+ if (!fmtinfo) {
+ fmtinfo = &unicam_image_formats[0];
+ pix->pixelformat = fmtinfo->fourcc;
+ }
+
+ unicam_calc_image_size_bpl(node->dev, fmtinfo, pix);
+
+ if (pix->field == V4L2_FIELD_ANY)
+ pix->field = V4L2_FIELD_NONE;
+
+ return fmtinfo;
+}
+
+static int unicam_try_fmt_vid(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ __unicam_try_fmt_vid(node, &f->fmt.pix);
+ return 0;
+}
+
+static int unicam_s_fmt_vid(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (vb2_is_busy(&node->buffer_queue))
+ return -EBUSY;
+
+ node->fmtinfo = __unicam_try_fmt_vid(node, &f->fmt.pix);
+ node->fmt = *f;
+
+ return 0;
+}
+
+static int unicam_enum_fmt_meta(struct file *file, void *priv,
+ struct v4l2_fmtdesc *f)
+{
+ unsigned int i, index;
+
+ for (i = 0, index = 0; i < ARRAY_SIZE(unicam_meta_formats); i++) {
+ if (f->mbus_code && unicam_meta_formats[i].code != f->mbus_code)
+ continue;
+
+ if (index == f->index) {
+ f->pixelformat = unicam_meta_formats[i].fourcc;
+ f->type = V4L2_BUF_TYPE_META_CAPTURE;
+ f->flags = V4L2_FMT_FLAG_META_LINE_BASED;
+ return 0;
+ }
+
+ index++;
+ }
+
+ return -EINVAL;
+}
+
+static int unicam_g_fmt_meta(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ f->fmt.meta = node->fmt.fmt.meta;
+
+ return 0;
+}
+
+static const struct unicam_format_info *
+__unicam_try_fmt_meta(struct unicam_node *node, struct v4l2_meta_format *meta)
+{
+ const struct unicam_format_info *fmtinfo;
+
+ /*
+ * Default to the first format if the requested pixel format code isn't
+ * supported.
+ */
+ fmtinfo = unicam_find_format_by_fourcc(meta->dataformat,
+ UNICAM_SD_PAD_SOURCE_METADATA);
+ if (!fmtinfo) {
+ fmtinfo = &unicam_meta_formats[0];
+ meta->dataformat = fmtinfo->fourcc;
+ }
+
+ unicam_calc_meta_size_bpl(node->dev, fmtinfo, meta);
+
+ return fmtinfo;
+}
+
+static int unicam_try_fmt_meta(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ __unicam_try_fmt_vid(node, &f->fmt.pix);
+ return 0;
+}
+
+static int unicam_s_fmt_meta(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (vb2_is_busy(&node->buffer_queue))
+ return -EBUSY;
+
+ node->fmtinfo = __unicam_try_fmt_meta(node, &f->fmt.meta);
+ node->fmt = *f;
+
+ return 0;
+}
+
+static int unicam_enum_framesizes(struct file *file, void *fh,
+ struct v4l2_frmsizeenum *fsize)
+{
+ struct unicam_node *node = video_drvdata(file);
+ int ret = -EINVAL;
+
+ if (fsize->index > 0)
+ return ret;
+
+ if (is_image_node(node)) {
+ if (!unicam_find_format_by_fourcc(fsize->pixel_format,
+ UNICAM_SD_PAD_SOURCE_IMAGE))
+ return ret;
+
+ fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE;
+ fsize->stepwise.min_width = UNICAM_IMAGE_MIN_WIDTH;
+ fsize->stepwise.max_width = UNICAM_IMAGE_MAX_WIDTH;
+ fsize->stepwise.step_width = 1;
+ fsize->stepwise.min_height = UNICAM_IMAGE_MIN_HEIGHT;
+ fsize->stepwise.max_height = UNICAM_IMAGE_MAX_HEIGHT;
+ fsize->stepwise.step_height = 1;
+ } else {
+ if (!unicam_find_format_by_fourcc(fsize->pixel_format,
+ UNICAM_SD_PAD_SOURCE_METADATA))
+ return ret;
+
+ fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE;
+ fsize->stepwise.min_width = UNICAM_META_MIN_WIDTH;
+ fsize->stepwise.max_width = UNICAM_META_MAX_WIDTH;
+ fsize->stepwise.step_width = 1;
+ fsize->stepwise.min_height = UNICAM_META_MIN_HEIGHT;
+ fsize->stepwise.max_height = UNICAM_META_MAX_HEIGHT;
+ fsize->stepwise.step_height = 1;
+ }
+
+ return 0;
+}
+
+static int unicam_log_status(struct file *file, void *fh)
+{
+ struct unicam_node *node = video_drvdata(file);
+ struct unicam_device *unicam = node->dev;
+ u32 reg;
+
+ /* status for sub devices */
+ v4l2_device_call_all(&unicam->v4l2_dev, 0, core, log_status);
+
+ dev_info(unicam->dev, "-----Receiver status-----\n");
+ dev_info(unicam->dev, "V4L2 width/height: %ux%u\n",
+ node->fmt.fmt.pix.width, node->fmt.fmt.pix.height);
+ dev_info(unicam->dev, "Mediabus format: %08x\n",
+ node->fmtinfo->code);
+ dev_info(unicam->dev, "V4L2 format: %08x\n",
+ node->fmt.fmt.pix.pixelformat);
+ reg = unicam_reg_read(unicam, UNICAM_IPIPE);
+ dev_info(unicam->dev, "Unpacking/packing: %u / %u\n",
+ unicam_get_field(reg, UNICAM_PUM_MASK),
+ unicam_get_field(reg, UNICAM_PPM_MASK));
+ dev_info(unicam->dev, "----Live data----\n");
+ dev_info(unicam->dev, "Programmed stride: %4u\n",
+ unicam_reg_read(unicam, UNICAM_IBLS));
+ dev_info(unicam->dev, "Detected resolution: %ux%u\n",
+ unicam_reg_read(unicam, UNICAM_IHSTA),
+ unicam_reg_read(unicam, UNICAM_IVSTA));
+ dev_info(unicam->dev, "Write pointer: %08x\n",
+ unicam_reg_read(unicam, UNICAM_IBWP));
+
+ return 0;
+}
+
+static int unicam_subscribe_event(struct v4l2_fh *fh,
+ const struct v4l2_event_subscription *sub)
+{
+ switch (sub->type) {
+ case V4L2_EVENT_FRAME_SYNC:
+ return v4l2_event_subscribe(fh, sub, 2, NULL);
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct v4l2_ioctl_ops unicam_ioctl_ops = {
+ .vidioc_querycap = unicam_querycap,
+
+ .vidioc_enum_fmt_vid_cap = unicam_enum_fmt_vid,
+ .vidioc_g_fmt_vid_cap = unicam_g_fmt_vid,
+ .vidioc_try_fmt_vid_cap = unicam_try_fmt_vid,
+ .vidioc_s_fmt_vid_cap = unicam_s_fmt_vid,
+
+ .vidioc_enum_fmt_meta_cap = unicam_enum_fmt_meta,
+ .vidioc_g_fmt_meta_cap = unicam_g_fmt_meta,
+ .vidioc_try_fmt_meta_cap = unicam_try_fmt_meta,
+ .vidioc_s_fmt_meta_cap = unicam_s_fmt_meta,
+
+ .vidioc_enum_framesizes = unicam_enum_framesizes,
+
+ .vidioc_reqbufs = vb2_ioctl_reqbufs,
+ .vidioc_create_bufs = vb2_ioctl_create_bufs,
+ .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
+ .vidioc_querybuf = vb2_ioctl_querybuf,
+ .vidioc_qbuf = vb2_ioctl_qbuf,
+ .vidioc_dqbuf = vb2_ioctl_dqbuf,
+ .vidioc_expbuf = vb2_ioctl_expbuf,
+ .vidioc_streamon = vb2_ioctl_streamon,
+ .vidioc_streamoff = vb2_ioctl_streamoff,
+
+ .vidioc_log_status = unicam_log_status,
+ .vidioc_subscribe_event = unicam_subscribe_event,
+ .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
+};
+
+/* unicam capture driver file operations */
+static const struct v4l2_file_operations unicam_fops = {
+ .owner = THIS_MODULE,
+ .open = v4l2_fh_open,
+ .release = vb2_fop_release,
+ .poll = vb2_fop_poll,
+ .unlocked_ioctl = video_ioctl2,
+ .mmap = vb2_fop_mmap,
+};
+
+static int unicam_video_link_validate(struct media_link *link)
+{
+ struct video_device *vdev =
+ media_entity_to_video_device(link->sink->entity);
+ struct v4l2_subdev *sd =
+ media_entity_to_v4l2_subdev(link->source->entity);
+ struct unicam_node *node = video_get_drvdata(vdev);
+ const u32 pad = is_image_node(node) ? UNICAM_SD_PAD_SOURCE_IMAGE
+ : UNICAM_SD_PAD_SOURCE_METADATA;
+ const struct v4l2_mbus_framefmt *format;
+ struct v4l2_subdev_state *state;
+ int ret = 0;
+
+ state = v4l2_subdev_lock_and_get_active_state(sd);
+
+ format = v4l2_subdev_state_get_format(state, pad, 0);
+ if (!format) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (is_image_node(node)) {
+ const struct v4l2_pix_format *fmt = &node->fmt.fmt.pix;
+
+ if (node->fmtinfo->code != format->code ||
+ fmt->height != format->height ||
+ fmt->width != format->width ||
+ fmt->field != format->field) {
+ dev_dbg(node->dev->dev,
+ "image: (%u x %u) 0x%08x %s != (%u x %u) 0x%08x %s\n",
+ fmt->width, fmt->height, node->fmtinfo->code,
+ v4l2_field_names[fmt->field],
+ format->width, format->height, format->code,
+ v4l2_field_names[format->field]);
+ ret = -EPIPE;
+ }
+ } else {
+ const struct v4l2_meta_format *fmt = &node->fmt.fmt.meta;
+
+ if (node->fmtinfo->code != format->code ||
+ fmt->height != format->height ||
+ fmt->width != format->width) {
+ dev_dbg(node->dev->dev,
+ "meta: (%u x %u) 0x%04x != (%u x %u) 0x%04x\n",
+ fmt->width, fmt->height, node->fmtinfo->code,
+ format->width, format->height, format->code);
+ ret = -EPIPE;
+ }
+ }
+
+out:
+ v4l2_subdev_unlock_state(state);
+ return ret;
+}
+
+static const struct media_entity_operations unicam_video_media_ops = {
+ .link_validate = unicam_video_link_validate,
+};
+
+static void unicam_node_release(struct video_device *vdev)
+{
+ struct unicam_node *node = video_get_drvdata(vdev);
+
+ unicam_put(node->dev);
+}
+
+static void unicam_set_default_format(struct unicam_node *node)
+{
+ if (is_image_node(node)) {
+ struct v4l2_pix_format *fmt = &node->fmt.fmt.pix;
+
+ node->fmtinfo = &unicam_image_formats[0];
+ node->fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+
+ v4l2_fill_pix_format(fmt, &unicam_default_image_format);
+ fmt->pixelformat = node->fmtinfo->fourcc;
+ unicam_calc_image_size_bpl(node->dev, node->fmtinfo, fmt);
+ } else {
+ struct v4l2_meta_format *fmt = &node->fmt.fmt.meta;
+
+ node->fmtinfo = &unicam_meta_formats[0];
+ node->fmt.type = V4L2_BUF_TYPE_META_CAPTURE;
+
+ fmt->dataformat = node->fmtinfo->fourcc;
+ fmt->width = unicam_default_meta_format.width;
+ fmt->height = unicam_default_meta_format.height;
+ unicam_calc_meta_size_bpl(node->dev, node->fmtinfo, fmt);
+ }
+}
+
+static int unicam_register_node(struct unicam_device *unicam,
+ enum unicam_node_type type)
+{
+ const u32 pad_index = type == UNICAM_IMAGE_NODE
+ ? UNICAM_SD_PAD_SOURCE_IMAGE
+ : UNICAM_SD_PAD_SOURCE_METADATA;
+ struct unicam_node *node = &unicam->node[type];
+ struct video_device *vdev = &node->video_dev;
+ struct vb2_queue *q = &node->buffer_queue;
+ int ret;
+
+ node->dev = unicam_get(unicam);
+ node->id = type;
+
+ spin_lock_init(&node->dma_queue_lock);
+
+ INIT_LIST_HEAD(&node->dma_queue);
+
+ /* Initialize the videobuf2 queue. */
+ q->type = type == UNICAM_IMAGE_NODE ? V4L2_BUF_TYPE_VIDEO_CAPTURE
+ : V4L2_BUF_TYPE_META_CAPTURE;
+ q->io_modes = VB2_MMAP | VB2_DMABUF;
+ q->drv_priv = node;
+ q->ops = &unicam_video_qops;
+ q->mem_ops = &vb2_dma_contig_memops;
+ q->buf_struct_size = sizeof(struct unicam_buffer);
+ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+ q->lock = &unicam->lock;
+ q->min_queued_buffers = 1;
+ q->dev = unicam->dev;
+
+ ret = vb2_queue_init(q);
+ if (ret) {
+ dev_err(unicam->dev, "vb2_queue_init() failed\n");
+ goto err_unicam_put;
+ }
+
+ /* Initialize the video device. */
+ vdev->release = unicam_node_release;
+ vdev->fops = &unicam_fops;
+ vdev->ioctl_ops = &unicam_ioctl_ops;
+ vdev->v4l2_dev = &unicam->v4l2_dev;
+ vdev->vfl_dir = VFL_DIR_RX;
+ vdev->queue = q;
+ vdev->lock = &unicam->lock;
+ vdev->device_caps = type == UNICAM_IMAGE_NODE
+ ? V4L2_CAP_VIDEO_CAPTURE : V4L2_CAP_META_CAPTURE;
+ vdev->device_caps |= V4L2_CAP_STREAMING | V4L2_CAP_IO_MC;
+ vdev->entity.ops = &unicam_video_media_ops;
+
+ snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME,
+ type == UNICAM_IMAGE_NODE ? "image" : "embedded");
+
+ video_set_drvdata(vdev, node);
+
+ if (type == UNICAM_IMAGE_NODE)
+ vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT;
+
+ node->pad.flags = MEDIA_PAD_FL_SINK;
+
+ ret = media_entity_pads_init(&vdev->entity, 1, &node->pad);
+ if (ret)
+ goto err_unicam_put;
+
+ node->dummy_buf.size = UNICAM_DUMMY_BUF_SIZE;
+ node->dummy_buf_cpu_addr = dma_alloc_coherent(unicam->dev,
+ node->dummy_buf.size,
+ &node->dummy_buf.dma_addr,
+ GFP_KERNEL);
+ if (!node->dummy_buf_cpu_addr) {
+ dev_err(unicam->dev, "Unable to allocate dummy buffer.\n");
+ ret = -ENOMEM;
+ goto err_entity_cleanup;
+ }
+
+ unicam_set_default_format(node);
+
+ ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1);
+ if (ret) {
+ dev_err(unicam->dev, "Unable to register video device %s\n",
+ vdev->name);
+ goto err_dma_free;
+ }
+
+ node->registered = true;
+
+ ret = media_create_pad_link(&unicam->subdev.sd.entity,
+ pad_index,
+ &node->video_dev.entity,
+ 0,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret) {
+ /*
+ * No need for cleanup, the caller will unregister the
+ * video device, which will drop the reference on the
+ * device and trigger the cleanup.
+ */
+ dev_err(unicam->dev, "Unable to create pad link for %s\n",
+ unicam->sensor.subdev->name);
+ return ret;
+ }
+
+ return 0;
+
+err_dma_free:
+ dma_free_coherent(unicam->dev, node->dummy_buf.size,
+ node->dummy_buf_cpu_addr,
+ node->dummy_buf.dma_addr);
+err_entity_cleanup:
+ media_entity_cleanup(&vdev->entity);
+err_unicam_put:
+ unicam_put(unicam);
+ return ret;
+}
+
+static void unicam_unregister_nodes(struct unicam_device *unicam)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ struct unicam_node *node = &unicam->node[i];
+
+ if (node->dummy_buf_cpu_addr)
+ dma_free_coherent(unicam->dev, node->dummy_buf.size,
+ node->dummy_buf_cpu_addr,
+ node->dummy_buf.dma_addr);
+
+ if (node->registered) {
+ video_unregister_device(&node->video_dev);
+ node->registered = false;
+ }
+ }
+}
+
+/* -----------------------------------------------------------------------------
+ * Power management
+ */
+
+static int unicam_runtime_resume(struct device *dev)
+{
+ struct unicam_device *unicam = dev_get_drvdata(dev);
+ int ret;
+
+ ret = clk_set_min_rate(unicam->vpu_clock, UNICAM_MIN_VPU_CLOCK_RATE);
+ if (ret) {
+ dev_err(unicam->dev, "failed to set up VPU clock\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(unicam->vpu_clock);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to enable VPU clock: %d\n", ret);
+ goto err_vpu_clock;
+ }
+
+ ret = clk_set_rate(unicam->clock, 100 * 1000 * 1000);
+ if (ret) {
+ dev_err(unicam->dev, "failed to set up CSI clock\n");
+ goto err_vpu_prepare;
+ }
+
+ ret = clk_prepare_enable(unicam->clock);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to enable CSI clock: %d\n", ret);
+ goto err_vpu_prepare;
+ }
+
+ return 0;
+
+err_vpu_prepare:
+ clk_disable_unprepare(unicam->vpu_clock);
+err_vpu_clock:
+ if (clk_set_min_rate(unicam->vpu_clock, 0))
+ dev_err(unicam->dev, "failed to reset the VPU clock\n");
+
+ return ret;
+}
+
+static int unicam_runtime_suspend(struct device *dev)
+{
+ struct unicam_device *unicam = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(unicam->clock);
+
+ if (clk_set_min_rate(unicam->vpu_clock, 0))
+ dev_err(unicam->dev, "failed to reset the VPU clock\n");
+
+ clk_disable_unprepare(unicam->vpu_clock);
+
+ return 0;
+}
+
+static const struct dev_pm_ops unicam_pm_ops = {
+ RUNTIME_PM_OPS(unicam_runtime_suspend, unicam_runtime_resume, NULL)
+};
+
+/* -----------------------------------------------------------------------------
+ * V4L2 async notifier
+ */
+
+static int unicam_async_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *subdev,
+ struct v4l2_async_connection *asc)
+{
+ struct unicam_device *unicam = notifier_to_unicam_device(notifier);
+ struct media_pad *sink = &unicam->subdev.pads[UNICAM_SD_PAD_SINK];
+ struct media_pad *source;
+ int ret;
+
+ dev_dbg(unicam->dev, "Using sensor %s for capture\n",
+ subdev->name);
+
+ ret = v4l2_create_fwnode_links_to_pad(subdev, sink, MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret)
+ return ret;
+
+ source = media_pad_remote_pad_unique(sink);
+ if (!source) {
+ dev_err(unicam->dev, "No connected sensor pad\n");
+ return -ENOTCONN;
+ }
+
+ unicam->sensor.subdev = subdev;
+ unicam->sensor.pad = source;
+
+ return 0;
+}
+
+static int unicam_async_complete(struct v4l2_async_notifier *notifier)
+{
+ struct unicam_device *unicam = notifier_to_unicam_device(notifier);
+ int ret;
+
+ ret = unicam_register_node(unicam, UNICAM_IMAGE_NODE);
+ if (ret) {
+ dev_err(unicam->dev, "Unable to register image video device.\n");
+ goto unregister;
+ }
+
+ ret = unicam_register_node(unicam, UNICAM_METADATA_NODE);
+ if (ret) {
+ dev_err(unicam->dev, "Unable to register metadata video device.\n");
+ goto unregister;
+ }
+
+ ret = v4l2_device_register_subdev_nodes(&unicam->v4l2_dev);
+ if (ret) {
+ dev_err(unicam->dev, "Unable to register subdev nodes.\n");
+ goto unregister;
+ }
+
+ return 0;
+
+unregister:
+ unicam_unregister_nodes(unicam);
+ unicam_put(unicam);
+
+ return ret;
+}
+
+static const struct v4l2_async_notifier_operations unicam_async_ops = {
+ .bound = unicam_async_bound,
+ .complete = unicam_async_complete,
+};
+
+static int unicam_async_nf_init(struct unicam_device *unicam)
+{
+ struct v4l2_fwnode_endpoint ep = { };
+ struct fwnode_handle *ep_handle;
+ struct v4l2_async_connection *asc;
+ int ret;
+
+ ret = of_property_read_u32(unicam->dev->of_node, "brcm,num-data-lanes",
+ &unicam->max_data_lanes);
+ if (ret < 0) {
+ dev_err(unicam->dev, "Missing %s DT property\n",
+ "brcm,num-data-lanes");
+ return -EINVAL;
+ }
+
+ /* Get and parse the local endpoint. */
+ ep_handle = fwnode_graph_get_endpoint_by_id(dev_fwnode(unicam->dev), 0, 0,
+ FWNODE_GRAPH_ENDPOINT_NEXT);
+ if (!ep_handle) {
+ dev_err(unicam->dev, "No endpoint found\n");
+ return -ENODEV;
+ }
+
+ ret = v4l2_fwnode_endpoint_parse(ep_handle, &ep);
+ if (ret) {
+ dev_err(unicam->dev, "Failed to parse endpoint: %d\n", ret);
+ goto error;
+ }
+
+ unicam->bus_type = ep.bus_type;
+
+ switch (ep.bus_type) {
+ case V4L2_MBUS_CSI2_DPHY: {
+ unsigned int num_data_lanes = ep.bus.mipi_csi2.num_data_lanes;
+
+ if (num_data_lanes != 1 && num_data_lanes != 2 &&
+ num_data_lanes != 4) {
+ dev_err(unicam->dev, "%u data lanes not supported\n",
+ num_data_lanes);
+ goto error;
+ }
+
+ if (num_data_lanes > unicam->max_data_lanes) {
+ dev_err(unicam->dev,
+ "Endpoint uses %u data lanes when %u are supported\n",
+ num_data_lanes, unicam->max_data_lanes);
+ goto error;
+ }
+
+ unicam->max_data_lanes = num_data_lanes;
+ unicam->bus_flags = ep.bus.mipi_csi2.flags;
+ break;
+ }
+
+ case V4L2_MBUS_CCP2:
+ unicam->max_data_lanes = 1;
+ unicam->bus_flags = ep.bus.mipi_csi1.strobe;
+ break;
+
+ default:
+ /* Unsupported bus type */
+ dev_err(unicam->dev, "Unsupported bus type %u\n", ep.bus_type);
+ goto error;
+ }
+
+ /* Initialize and register the async notifier. */
+ v4l2_async_nf_init(&unicam->notifier, &unicam->v4l2_dev);
+
+ asc = v4l2_async_nf_add_fwnode_remote(&unicam->notifier, ep_handle,
+ struct v4l2_async_connection);
+ fwnode_handle_put(ep_handle);
+ ep_handle = NULL;
+
+ if (IS_ERR(asc)) {
+ ret = PTR_ERR(asc);
+ dev_err(unicam->dev, "Failed to add entry to notifier: %d\n",
+ ret);
+ goto error;
+ }
+
+ unicam->notifier.ops = &unicam_async_ops;
+
+ ret = v4l2_async_nf_register(&unicam->notifier);
+ if (ret) {
+ dev_err(unicam->dev, "Error registering device notifier: %d\n",
+ ret);
+ goto error;
+ }
+
+ return 0;
+
+error:
+ fwnode_handle_put(ep_handle);
+ return ret;
+}
+
+/* -----------------------------------------------------------------------------
+ * Probe & remove
+ */
+
+static int unicam_media_init(struct unicam_device *unicam)
+{
+ int ret;
+
+ unicam->mdev.dev = unicam->dev;
+ strscpy(unicam->mdev.model, UNICAM_MODULE_NAME,
+ sizeof(unicam->mdev.model));
+ unicam->mdev.hw_revision = 0;
+
+ media_device_init(&unicam->mdev);
+
+ unicam->v4l2_dev.mdev = &unicam->mdev;
+
+ ret = v4l2_device_register(unicam->dev, &unicam->v4l2_dev);
+ if (ret < 0) {
+ dev_err(unicam->dev, "Unable to register v4l2 device\n");
+ goto err_media_cleanup;
+ }
+
+ ret = media_device_register(&unicam->mdev);
+ if (ret < 0) {
+ dev_err(unicam->dev,
+ "Unable to register media-controller device\n");
+ goto err_v4l2_unregister;
+ }
+
+ return 0;
+
+err_v4l2_unregister:
+ v4l2_device_unregister(&unicam->v4l2_dev);
+err_media_cleanup:
+ media_device_cleanup(&unicam->mdev);
+ return ret;
+}
+
+static int unicam_probe(struct platform_device *pdev)
+{
+ struct unicam_device *unicam;
+ int ret;
+
+ unicam = kzalloc(sizeof(*unicam), GFP_KERNEL);
+ if (!unicam)
+ return -ENOMEM;
+
+ kref_init(&unicam->kref);
+ mutex_init(&unicam->lock);
+
+ unicam->dev = &pdev->dev;
+ platform_set_drvdata(pdev, unicam);
+
+ unicam->base = devm_platform_ioremap_resource_byname(pdev, "unicam");
+ if (IS_ERR(unicam->base)) {
+ ret = PTR_ERR(unicam->base);
+ goto err_unicam_put;
+ }
+
+ unicam->clk_gate_base = devm_platform_ioremap_resource_byname(pdev, "cmi");
+ if (IS_ERR(unicam->clk_gate_base)) {
+ ret = PTR_ERR(unicam->clk_gate_base);
+ goto err_unicam_put;
+ }
+
+ unicam->clock = devm_clk_get(&pdev->dev, "lp");
+ if (IS_ERR(unicam->clock)) {
+ dev_err(unicam->dev, "Failed to get lp clock\n");
+ ret = PTR_ERR(unicam->clock);
+ goto err_unicam_put;
+ }
+
+ unicam->vpu_clock = devm_clk_get(&pdev->dev, "vpu");
+ if (IS_ERR(unicam->vpu_clock)) {
+ dev_err(unicam->dev, "Failed to get vpu clock\n");
+ ret = PTR_ERR(unicam->vpu_clock);
+ goto err_unicam_put;
+ }
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret <= 0) {
+ dev_err(&pdev->dev, "No IRQ resource\n");
+ ret = -EINVAL;
+ goto err_unicam_put;
+ }
+
+ ret = devm_request_irq(&pdev->dev, ret, unicam_isr, 0,
+ "unicam_capture0", unicam);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to request interrupt\n");
+ ret = -EINVAL;
+ goto err_unicam_put;
+ }
+
+ /* Enable the block power domain. */
+ pm_runtime_enable(&pdev->dev);
+
+ ret = unicam_media_init(unicam);
+ if (ret)
+ goto err_pm_runtime;
+
+ ret = unicam_subdev_init(unicam);
+ if (ret)
+ goto err_media_unregister;
+
+ ret = unicam_async_nf_init(unicam);
+ if (ret)
+ goto err_subdev_unregister;
+
+ return 0;
+
+err_subdev_unregister:
+ unicam_subdev_cleanup(unicam);
+err_media_unregister:
+ media_device_unregister(&unicam->mdev);
+err_pm_runtime:
+ pm_runtime_disable(&pdev->dev);
+err_unicam_put:
+ unicam_put(unicam);
+
+ return ret;
+}
+
+static int unicam_remove(struct platform_device *pdev)
+{
+ struct unicam_device *unicam = platform_get_drvdata(pdev);
+
+ unicam_unregister_nodes(unicam);
+ v4l2_device_unregister(&unicam->v4l2_dev);
+ media_device_unregister(&unicam->mdev);
+ v4l2_async_nf_unregister(&unicam->notifier);
+
+ unicam_subdev_cleanup(unicam);
+
+ unicam_put(unicam);
+
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+static const struct of_device_id unicam_of_match[] = {
+ { .compatible = "brcm,bcm2835-unicam", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, unicam_of_match);
+
+static struct platform_driver unicam_driver = {
+ .probe = unicam_probe,
+ .remove = unicam_remove,
+ .driver = {
+ .name = UNICAM_MODULE_NAME,
+ .pm = pm_ptr(&unicam_pm_ops),
+ .of_match_table = of_match_ptr(unicam_of_match),
+ },
+};
+
+module_platform_driver(unicam_driver);
+
+MODULE_AUTHOR("Dave Stevenson <dave.stevenson@raspberrypi.com>");
+MODULE_DESCRIPTION("BCM2835 Unicam driver");
+MODULE_LICENSE("GPL");