diff --git a/include/uapi/linux/media/arm/mali-c55-config.h b/include/uapi/linux/media/arm/mali-c55-config.h
index 21b453bdee5d..b31415597e88 100644
--- a/include/uapi/linux/media/arm/mali-c55-config.h
+++ b/include/uapi/linux/media/arm/mali-c55-config.h
@@ -179,4 +179,731 @@ struct mali_c55_stats_buffer {
 	__u32 reserved3[15];
 } __attribute__((packed));
 
+/**
+ * enum mali_c55_param_buffer_version - Mali-C55 parameters block versioning
+ *
+ * @MALI_C55_PARAM_BUFFER_V1: First version of Mali-C55 parameters block
+ */
+enum mali_c55_param_buffer_version {
+	MALI_C55_PARAM_BUFFER_V1,
+};
+
+/**
+ * enum mali_c55_param_block_type - Enumeration of Mali-C55 parameter blocks
+ *
+ * This enumeration defines the types of Mali-C55 parameters block. Each block
+ * configures a specific processing block of the Mali-C55 ISP. The block
+ * type allows the driver to correctly interpret the parameters block data.
+ *
+ * It is the responsibility of userspace to correctly set the type of each
+ * parameters block.
+ *
+ * @MALI_C55_PARAM_BLOCK_SENSOR_OFFS: Sensor pre-shading black level offset
+ * @MALI_C55_PARAM_BLOCK_AEXP_HIST: Auto-exposure 1024-bin histogram
+ *				    configuration
+ * @MALI_C55_PARAM_BLOCK_AEXP_IHIST: Post-Iridix auto-exposure 1024-bin
+ *				     histogram configuration
+ * @MALI_C55_PARAM_BLOCK_AEXP_HIST_WEIGHTS: Auto-exposure 1024-bin histogram
+ *					    weighting
+ * @MALI_C55_PARAM_BLOCK_AEXP_IHIST_WEIGHTS: Post-Iridix auto-exposure 1024-bin
+ *					     histogram weighting
+ * @MALI_C55_PARAM_BLOCK_DIGITAL_GAIN: Digital gain
+ * @MALI_C55_PARAM_BLOCK_AWB_GAINS: Auto-white balance gains
+ * @MALI_C55_PARAM_BLOCK_AWB_CONFIG: Auto-white balance statistics config
+ * @MALI_C55_PARAM_BLOCK_AWB_GAINS_AEXP: Auto-white balance gains for AEXP-0 tap
+ * @MALI_C55_PARAM_MESH_SHADING_CONFIG : Mesh shading tables configuration
+ * @MALI_C55_PARAM_MESH_SHADING_SELECTION: Mesh shading table selection
+ */
+enum mali_c55_param_block_type {
+	MALI_C55_PARAM_BLOCK_SENSOR_OFFS,
+	MALI_C55_PARAM_BLOCK_AEXP_HIST,
+	MALI_C55_PARAM_BLOCK_AEXP_IHIST,
+	MALI_C55_PARAM_BLOCK_AEXP_HIST_WEIGHTS,
+	MALI_C55_PARAM_BLOCK_AEXP_IHIST_WEIGHTS,
+	MALI_C55_PARAM_BLOCK_DIGITAL_GAIN,
+	MALI_C55_PARAM_BLOCK_AWB_GAINS,
+	MALI_C55_PARAM_BLOCK_AWB_CONFIG,
+	MALI_C55_PARAM_BLOCK_AWB_GAINS_AEXP,
+	MALI_C55_PARAM_MESH_SHADING_CONFIG,
+	MALI_C55_PARAM_MESH_SHADING_SELECTION,
+};
+
+#define MALI_C55_PARAM_BLOCK_FL_NONE			0
+#define MALI_C55_PARAM_BLOCK_FL_DISABLED		BIT(0)
+
+/**
+ * struct mali_c55_params_block_header - Mali-C55 parameter block header
+ *
+ * This structure represents the common part of all the ISP configuration
+ * blocks. Each parameters block embeds an instance of this structure type
+ * as its first member, followed by the block-specific configuration data. The
+ * driver inspects this common header to discern the block type and its size and
+ * properly handle the block content by casting it to the correct block-specific
+ * type.
+ *
+ * The @type field is one of the values enumerated by
+ * :c:type:`mali_c55_param_block_type` and specifies how the data should be
+ * interpreted by the driver. The @size field specifies the size of the
+ * parameters block and is used by the driver for validation purposes. The
+ * @flags field holds a bitmask of per-block flags MALI_C55_PARAM_BLOCK_FL_*.
+ *
+ * If userspace wants to disable an ISP block the
+ * MALI_C55_PARAM_BLOCK_FL_DISABLED bit should be set in the @flags field. In
+ * that case userspace may optionally omit the remainder of the configuration
+ * block, which will in any case be ignored by the driver. If a new
+ * configuration of an ISP block has to be applied userspace shall fully
+ * populate the ISP block and omit setting the MALI_C55_PARAM_BLOCK_FL_DISABLED
+ * bit in the @flags field.
+ *
+ * Userspace is responsible for correctly populating the parameters block header
+ * fields (@type, @flags and @size) and correctly populate the block-specific
+ * parameters.
+ *
+ * For example:
+ *
+ * .. code-block:: c
+ *
+ *	void populate_sensor_offs(struct mali_c55_params_block_header *block) {
+ *		block->type = MALI_C55_PARAM_BLOCK_SENSOR_OFFS;
+ *		block->enabled = MALI_C55_PARAM_BLOCK_FL_NONE;
+ *		block->size = sizeof(struct mali_c55_params_sensor_off_preshading);
+ *
+ *		struct mali_c55_params_sensor_off_preshading *sensor_offs =
+ *			(struct mali_c55_params_sensor_off_preshading *)block;
+ *
+ *		sensor_offs->chan00 = offset00;
+ *		sensor_offs->chan01 = offset01;
+ *		sensor_offs->chan10 = offset10;
+ *		sensor_offs->chan11 = offset11;
+ *	}
+ *
+ * @type: The parameters block type from :c:type:`mali_c55_param_block_type`
+ * @flags: Bitmask of block flags
+ * @size: Size (in bytes) of the parameters block
+ */
+struct mali_c55_params_block_header {
+	__u16 type;
+	__u16 flags;
+	__u32 size;
+} __attribute__((aligned(8)));
+
+/**
+ * struct mali_c55_params_sensor_off_preshading - offset subtraction for each
+ *						  color channel
+ *
+ * Provides removal of the sensor black level from the sensor data. Separate
+ * offsets are provided for each of the four Bayer component color channels
+ * which are defaulted to R, Gr, Gb, B.
+ *
+ * header.type should be set to MALI_C55_PARAM_BLOCK_SENSOR_OFFS from
+ * :c:type:`mali_c55_param_block_type` for this block.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @chan00: Offset for color channel 00 (default: R)
+ * @chan01: Offset for color channel 01 (default: Gr)
+ * @chan10: Offset for color channel 10 (default: Gb)
+ * @chan11: Offset for color channel 11 (default: B)
+ */
+struct mali_c55_params_sensor_off_preshading {
+	struct mali_c55_params_block_header header;
+	__u32 chan00;
+	__u32 chan01;
+	__u32 chan10;
+	__u32 chan11;
+};
+
+/**
+ * enum mali_c55_aexp_hist_tap_points - Tap points for the AEXP histogram
+ * @MALI_C55_AEXP_HIST_TAP_WB: After static white balance
+ * @MALI_C55_AEXP_HIST_TAP_FS: After WDR Frame Stitch
+ * @MALI_C55_AEXP_HIST_TAP_TPG: After the test pattern generator
+ */
+enum mali_c55_aexp_hist_tap_points {
+	MALI_C55_AEXP_HIST_TAP_WB = 0,
+	MALI_C55_AEXP_HIST_TAP_FS,
+	MALI_C55_AEXP_HIST_TAP_TPG,
+};
+
+/**
+ * enum mali_c55_aexp_skip_x - Horizontal pixel skipping
+ * @MALI_C55_AEXP_SKIP_X_EVERY_2ND: Collect every 2nd pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_3RD: Collect every 3rd pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_4TH: Collect every 4th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_5TH: Collect every 5th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_8TH: Collect every 8th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_9TH: Collect every 9th pixel horizontally
+ */
+enum mali_c55_aexp_skip_x {
+	MALI_C55_AEXP_SKIP_X_EVERY_2ND,
+	MALI_C55_AEXP_SKIP_X_EVERY_3RD,
+	MALI_C55_AEXP_SKIP_X_EVERY_4TH,
+	MALI_C55_AEXP_SKIP_X_EVERY_5TH,
+	MALI_C55_AEXP_SKIP_X_EVERY_8TH,
+	MALI_C55_AEXP_SKIP_X_EVERY_9TH
+};
+
+/**
+ * enum mali_c55_aexp_skip_y - Vertical pixel skipping
+ * @MALI_C55_AEXP_SKIP_Y_ALL: Collect every single pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_2ND: Collect every 2nd pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_3RD: Collect every 3rd pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_4TH: Collect every 4th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_5TH: Collect every 5th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_8TH: Collect every 8th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_9TH: Collect every 9th pixel vertically
+ */
+enum mali_c55_aexp_skip_y {
+	MALI_C55_AEXP_SKIP_Y_ALL,
+	MALI_C55_AEXP_SKIP_Y_EVERY_2ND,
+	MALI_C55_AEXP_SKIP_Y_EVERY_3RD,
+	MALI_C55_AEXP_SKIP_Y_EVERY_4TH,
+	MALI_C55_AEXP_SKIP_Y_EVERY_5TH,
+	MALI_C55_AEXP_SKIP_Y_EVERY_8TH,
+	MALI_C55_AEXP_SKIP_Y_EVERY_9TH
+};
+
+/**
+ * enum mali_c55_aexp_row_column_offset - Start from the first or second row or
+ *					  column
+ * @MALI_C55_AEXP_FIRST_ROW_OR_COL:	Start from the first row / column
+ * @MALI_C55_AEXP_SECOND_ROW_OR_COL:	Start from the second row / column
+ */
+enum mali_c55_aexp_row_column_offset {
+	MALI_C55_AEXP_FIRST_ROW_OR_COL = 1,
+	MALI_C55_AEXP_SECOND_ROW_OR_COL = 2,
+};
+
+/**
+ * enum mali_c55_aexp_hist_plane_mode - Mode for the AEXP Histograms
+ * @MALI_C55_AEXP_HIST_COMBINED: All color planes in one 1024-bin histogram
+ * @MALI_C55_AEXP_HIST_SEPARATE: Each color plane in one 256-bin histogram with a bin width of 16
+ * @MALI_C55_AEXP_HIST_FOCUS_00: Top left plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_01: Top right plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_10: Bottom left plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_11: Bottom right plane in the first bank, rest in second bank
+ *
+ * In the "focus" modes statistics are collected into two 512-bin histograms
+ * with a bin width of 8. One colour plane is in the first histogram with the
+ * remainder combined into the second. The four options represent which of the
+ * four positions in a bayer pattern are the focused plane.
+ */
+enum mali_c55_aexp_hist_plane_mode {
+	MALI_C55_AEXP_HIST_COMBINED = 0,
+	MALI_C55_AEXP_HIST_SEPARATE = 1,
+	MALI_C55_AEXP_HIST_FOCUS_00 = 4,
+	MALI_C55_AEXP_HIST_FOCUS_01 = 5,
+	MALI_C55_AEXP_HIST_FOCUS_10 = 6,
+	MALI_C55_AEXP_HIST_FOCUS_11 = 7,
+};
+
+/**
+ * struct mali_c55_params_aexp_hist - configuration for AEXP metering hists
+ *
+ * This struct allows users to configure the 1024-bin AEXP histograms. Broadly
+ * speaking the parameters allow you to mask particular regions of the image and
+ * to select different kinds of histogram.
+ *
+ * The skip_x, offset_x, skip_y and offset_y fields allow users to ignore or
+ * mask pixels in the frame by their position relative to the top left pixel.
+ * First, the skip_y, offset_x and offset_y fields define which of the pixels
+ * within each 2x2 region will be counted in the statistics.
+ *
+ * If skip_y == 0 then two pixels from each covered region will be counted. If
+ * both offset_x and offset_y are zero, then the two left-most pixels in each
+ * 2x2 pixel region will be counted. Setting offset_x = 1 will discount the top
+ * left pixel and count the top right pixel. Setting offset_y = 1 will discount
+ * the bottom left pixel and count the bottom right pixel.
+ *
+ * If skip_y != 0 then only a single pixel from each region covered by the
+ * pattern will be counted. In this case offset_x controls whether the pixel
+ * that's counted is in the left (if offset_x == 0) or right (if offset_x == 1)
+ * column and offset_y controls whether the pixel that's counted is in the top
+ * (if offset_y == 0) or bottom (if offset_y == 1) row.
+ *
+ * The skip_x and skip_y fields control how the 2x2 pixel region is repeated
+ * across the image data. The first instance of the region is always in the top
+ * left of the image data. The skip_x field controls how many pixels are ignored
+ * in the x direction before the pixel masking region is repeated. The skip_y
+ * field controls how many pixels are ignored in the y direction before the
+ * pixel masking region is repeated.
+ *
+ * These fields can be used to reduce the number of pixels counted for the
+ * statistics, but it's important to be careful to configure them correctly.
+ * Some combinations of values will result in colour components from the input
+ * data being ignored entirely, for example in the following configuration:
+ *
+ * skip_x = 0
+ * offset_x = 0
+ * skip_y = 0
+ * offset_y = 0
+ *
+ * Only the R and Gb components of RGGB data that was input would be collected.
+ * Similarly in the following configuration:
+ *
+ * skip_x = 0
+ * offset_x = 0
+ * skip_y = 1
+ * offset_y = 1
+ *
+ * Only the Gb component of RGGB data that was input would be collected. To
+ * correct things such that all 4 colour components were included it would be
+ * necessary to set the skip_x and skip_y fields in a way that resulted in all
+ * four colour components being collected:
+ *
+ * skip_x = 1
+ * offset_x = 0
+ * skip_y = 1
+ * offset_y = 1
+ *
+ * header.type should be set to one of either MALI_C55_PARAM_BLOCK_AEXP_HIST or
+ * MALI_C55_PARAM_BLOCK_AEXP_IHIST from :c:type:`mali_c55_param_block_type`.
+ *
+ * @header:		The Mali-C55 parameters block header
+ * @skip_x:		Horizontal decimation. See enum mali_c55_aexp_skip_x
+ * @offset_x:		Skip the first column, or not. See enum mali_c55_aexp_row_column_offset
+ * @skip_y:		Vertical decimation. See enum mali_c55_aexp_skip_y
+ * @offset_y:		Skip the first row, or not. See enum mali_c55_aexp_row_column_offset
+ * @scale_bottom:	Scale pixels in bottom half of intensity range: 0=1x ,1=2x, 2=4x, 4=8x, 4=16x
+ * @scale_top:		scale pixels in top half of intensity range: 0=1x ,1=2x, 2=4x, 4=8x, 4=16x
+ * @plane_mode:		Plane separation mode. See enum mali_c55_aexp_hist_plane_mode
+ * @tap_point:		Tap point for histogram from enum mali_c55_aexp_hist_tap_points.
+ *			This parameter is unused for the post-Iridix Histogram
+ */
+struct mali_c55_params_aexp_hist {
+	struct mali_c55_params_block_header header;
+	__u8 skip_x;
+	__u8 offset_x;
+	__u8 skip_y;
+	__u8 offset_y;
+	__u8 scale_bottom;
+	__u8 scale_top;
+	__u8 plane_mode;
+	__u8 tap_point;
+};
+
+/**
+ * struct mali_c55_params_aexp_weights - Array of weights for AEXP metering
+ *
+ * This struct allows users to configure the weighting for both of the 1024-bin
+ * AEXP histograms. The pixel data collected for each zone is multiplied by the
+ * corresponding weight from this array, which may be zero if the intention is
+ * to mask off the zone entirely.
+ *
+ * header.type should be set to one of either MALI_C55_PARAM_BLOCK_AEXP_HIST_WEIGHTS
+ * or MALI_C55_PARAM_BLOCK_AEXP_IHIST_WEIGHTS from :c:type:`mali_c55_param_block_type`.
+ *
+ * @header:		The Mali-C55 parameters block header
+ * @nodes_used_horiz:	Number of active zones horizontally [0..15]
+ * @nodes_used_vert:	Number of active zones vertically [0..15]
+ * @zone_weights:	Zone weighting. Index is row*col where 0,0 is the top
+ *			left zone continuing in raster order. Each zone can be
+ *			weighted in the range [0..15]. The number of rows and
+ *			columns is defined by @nodes_used_vert and
+ *			@nodes_used_horiz
+ */
+struct mali_c55_params_aexp_weights {
+	struct mali_c55_params_block_header header;
+	__u8 nodes_used_horiz;
+	__u8 nodes_used_vert;
+	__u8 zone_weights[MALI_C55_MAX_ZONES];
+};
+
+/**
+ * struct mali_c55_params_digital_gain - Digital gain value
+ *
+ * This struct carries a digital gain value to set in the ISP.
+ *
+ * header.type should be set to MALI_C55_PARAM_BLOCK_DIGITAL_GAIN from
+ * :c:type:`mali_c55_param_block_type` for this block.
+ *
+ * @header:	The Mali-C55 parameters block header
+ * @gain:	The digital gain value to apply, in Q5.8 format.
+ */
+struct mali_c55_params_digital_gain {
+	struct mali_c55_params_block_header header;
+	__u16 gain;
+};
+
+/**
+ * enum mali_c55_awb_stats_mode - Statistics mode for AWB
+ * @MALI_C55_AWB_MODE_GRBR: Statistics collected as Green/Red and Blue/Red ratios
+ * @MALI_C55_AWB_MODE_RGBG: Statistics collected as Red/Green and Blue/Green ratios
+ */
+enum mali_c55_awb_stats_mode {
+	MALI_C55_AWB_MODE_GRBR = 0,
+	MALI_C55_AWB_MODE_RGBG,
+};
+
+/**
+ * struct mali_c55_params_awb_gains - Gain settings for auto white balance
+ *
+ * This struct allows users to configure the gains for auto-white balance. There
+ * are four gain settings corresponding to each colour channel in the bayer
+ * domain. Although named generically, the association between the gain applied
+ * and the colour channel is done automatically within the ISP depending on the
+ * input format, and so the following mapping always holds true::
+ *
+ *	gain00 = R
+ *	gain01 = Gr
+ *	gain10 = Gb
+ *	gain11 = B
+ *
+ * All of the gains are stored in Q4.8 format.
+ *
+ * header.type should be set to one of either MALI_C55_PARAM_BLOCK_AWB_GAINS or
+ * MALI_C55_PARAM_BLOCK_AWB_GAINS_AEXP from :c:type:`mali_c55_param_block_type`.
+ *
+ * @header:	The Mali-C55 parameters block header
+ * @gain00:	Multiplier for colour channel 00
+ * @gain01:	Multiplier for colour channel 01
+ * @gain10:	Multiplier for colour channel 10
+ * @gain11:	Multiplier for colour channel 11
+ */
+struct mali_c55_params_awb_gains {
+	struct mali_c55_params_block_header header;
+	__u16 gain00;
+	__u16 gain01;
+	__u16 gain10;
+	__u16 gain11;
+};
+
+/**
+ * enum mali_c55_params_awb_tap_points - Tap points for the AWB statistics
+ * @MALI_C55_AWB_STATS_TAP_PF: Immediately after the Purple Fringe block
+ * @MALI_C55_AWB_STATS_TAP_CNR: Immediately after the CNR block
+ */
+enum mali_c55_params_awb_tap_points {
+	MALI_C55_AWB_STATS_TAP_PF = 0,
+	MALI_C55_AWB_STATS_TAP_CNR,
+};
+
+/**
+ * struct mali_c55_params_awb_config - Stats settings for auto-white balance
+ *
+ * This struct allows the configuration of the statistics generated for auto
+ * white balance. Pixel intensity limits can be set to exclude overly bright or
+ * dark regions of an image from the statistics entirely. Colour ratio minima
+ * and maxima can be set to discount pixels who's ratios fall outside the
+ * defined boundaries; there are two sets of registers to do this - the
+ * "min/max" ratios which bound a region and the "high/low" ratios which further
+ * trim the upper and lower ratios. For example with the boundaries configured
+ * as follows, only pixels whos colour ratios falls into the region marked "A"
+ * would be counted::
+ *
+ *	                                                          cr_high
+ *	    2.0 |                                                   |
+ *	        |               cb_max --> _________________________v_____
+ *	    1.8 |                         |                         \    |
+ *	        |                         |                          \   |
+ *	    1.6 |                         |                           \  |
+ *	        |                         |                            \ |
+ *	 c  1.4 |               cb_low -->|\              A             \|<--  cb_high
+ *	 b      |                         | \                            |
+ *	    1.2 |                         |  \                           |
+ *	 r      |                         |   \                          |
+ *	 a  1.0 |              cb_min --> |____\_________________________|
+ *	 t      |                         ^    ^                         ^
+ *	 i  0.8 |                         |    |                         |
+ *	 o      |                      cr_min  |                       cr_max
+ *	 s  0.6 |                              |
+ *	        |                             cr_low
+ *	    0.4 |
+ *	        |
+ *	    0.2 |
+ *	        |
+ *	    0.0 |_______________________________________________________________
+ *	        0.0   0.2   0.4   0.6   0.8   1.0   1.2   1.4   1.6   1.8   2.0
+ *	                                   cr ratios
+ *
+ * header.type should be set to MALI_C55_PARAM_BLOCK_AWB_CONFIG from
+ * :c:type:`mali_c55_param_block_type` for this block.
+ *
+ * @header:		The Mali-C55 parameters block header
+ * @tap_point:		The tap point from enum mali_c55_params_awb_tap_points
+ * @stats_mode:		AWB statistics collection mode, see :c:type:`mali_c55_awb_stats_mode`
+ * @white_level:	Upper pixel intensity (I.E. raw pixel values) limit
+ * @black_level:	Lower pixel intensity (I.E. raw pixel values) limit
+ * @cr_max:		Maximum R/G ratio (Q4.8 format)
+ * @cr_min:		Minimum R/G ratio (Q4.8 format)
+ * @cb_max:		Maximum B/G ratio (Q4.8 format)
+ * @cb_min:		Minimum B/G ratio (Q4.8 format)
+ * @nodes_used_horiz:	Number of active zones horizontally [0..15]
+ * @nodes_used_vert:	Number of active zones vertically [0..15]
+ * @cr_high:		R/G ratio trim high (Q4.8 format)
+ * @cr_low:		R/G ratio trim low (Q4.8 format)
+ * @cb_high:		B/G ratio trim high (Q4.8 format)
+ * @cb_low:		B/G ratio trim low (Q4.8 format)
+ */
+struct mali_c55_params_awb_config {
+	struct mali_c55_params_block_header header;
+	__u8 tap_point;
+	__u8 stats_mode;
+	__u16 white_level;
+	__u16 black_level;
+	__u16 cr_max;
+	__u16 cr_min;
+	__u16 cb_max;
+	__u16 cb_min;
+	__u8 nodes_used_horiz;
+	__u8 nodes_used_vert;
+	__u16 cr_high;
+	__u16 cr_low;
+	__u16 cb_high;
+	__u16 cb_low;
+};
+
+#define MALI_C55_NUM_MESH_SHADING_ELEMENTS 3072
+
+/**
+ * struct mali_c55_params_mesh_shading_config - Mesh shading configuration
+ *
+ * The mesh shading correction module allows programming a separate table of
+ * either 16x16 or 32x32 node coefficients for 3 different light sources. The
+ * final correction coefficients applied are computed by blending the
+ * coefficients from two tables together.
+ *
+ * A page of 1024 32-bit integers is associated to each colour channel, with
+ * pages stored consecutively in memory. Each 32-bit integer packs 3 8-bit
+ * correction coefficients for a single node, one for each of the three light
+ * sources. The 8 most significant bits are unused. The following table
+ * describes the layout::
+ *
+ *	+----------- Page (Colour Plane) 0 -------------+
+ *	| @mesh[i]  | Mesh Point | Bits  | Light Source |
+ *	+-----------+------------+-------+--------------+
+ *	|         0 |        0,0 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|         1 |        0,1 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|       ... |        ... | ...   | ...          |
+ *	+-----------+------------+-------+--------------+
+ *	|      1023 |      31,31 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+----------- Page (Colour Plane) 1 -------------+
+ *	| @mesh[i]  | Mesh Point | Bits  | Light Source |
+ *	+-----------+------------+-------+--------------+
+ *	|      1024 |        0,0 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|      1025 |        0,1 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|       ... |        ... | ...   | ...          |
+ *	+-----------+------------+-------+--------------+
+ *	|      2047 |      31,31 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+----------- Page (Colour Plane) 2 -------------+
+ *	| @mesh[i]  | Mesh Point | Bits  | Light Source |
+ *	+-----------+------------+-------+--------------+
+ *	|      2048 |        0,0 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|      2049 |        0,1 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *	|       ... |        ... | ...   | ...          |
+ *	+-----------+------------+-------+--------------+
+ *	|      3071 |      31,31 | 16,23 | LS2          |
+ *	|           |            | 08-15 | LS1          |
+ *	|           |            | 00-07 | LS0          |
+ *	+-----------+------------+-------+--------------+
+ *
+ * The @mesh_scale member determines the precision and minimum and maximum gain.
+ * For example if @mesh_scale is 0 and therefore selects 0 - 2x gain, a value of
+ * 0 in a coefficient means 0.0 gain, a value of 128 means 1.0 gain and 255
+ * means 2.0 gain.
+ *
+ * header.type should be set to MALI_C55_PARAM_MESH_SHADING_CONFIG from
+ * :c:type:`mali_c55_param_block_type` for this block.
+ *
+ * @header:		The Mali-C55 parameters block header
+ * @mesh_show:		Output the mesh data rather than image data
+ * @mesh_scale:		Set the precision and maximum gain range of mesh shading
+ *				- 0 = 0-2x gain
+ *				- 1 = 0-4x gain
+ *				- 2 = 0-8x gain
+ *				- 3 = 0-16x gain
+ *				- 4 = 1-2x gain
+ *				- 5 = 1-3x gain
+ *				- 6 = 1-5x gain
+ *				- 7 = 1-9x gain
+ * @mesh_page_r:	Mesh page select for red colour plane [0..2]
+ * @mesh_page_g:	Mesh page select for green colour plane [0..2]
+ * @mesh_page_b:	Mesh page select for blue colour plane [0..2]
+ * @mesh_width:		Number of horizontal nodes minus 1 [15,31]
+ * @mesh_height:	Number of vertical nodes minus 1 [15,31]
+ * @mesh:		Mesh shading correction tables
+ */
+struct mali_c55_params_mesh_shading_config {
+	struct mali_c55_params_block_header header;
+	__u8 mesh_show;
+	__u8 mesh_scale;
+	__u8 mesh_page_r;
+	__u8 mesh_page_g;
+	__u8 mesh_page_b;
+	__u8 mesh_width;
+	__u8 mesh_height;
+	__u32 mesh[MALI_C55_NUM_MESH_SHADING_ELEMENTS];
+};
+
+/** enum mali_c55_params_mesh_alpha_bank - Mesh shading table bank selection
+ * @MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS1 - Select Light Sources 0 and 1
+ * @MALI_C55_MESH_ALPHA_BANK_LS1_AND_LS2 - Select Light Sources 1 and 2
+ * @MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS2 - Select Light Sources 0 and 2
+ */
+enum mali_c55_params_mesh_alpha_bank {
+	MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS1 = 0,
+	MALI_C55_MESH_ALPHA_BANK_LS1_AND_LS2 = 1,
+	MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS2 = 4
+};
+
+/**
+ * struct mali_c55_params_mesh_shading_selection - Mesh table selection
+ *
+ * The module computes the final correction coefficients by blending the ones
+ * from two light source tables, which are selected (independently for each
+ * colour channel) by the @mesh_alpha_bank_r/g/b fields.
+ *
+ * The final blended coefficients for each node are calculated using the
+ * following equation:
+ *
+ *     Final coefficient = (a * LS\ :sub:`b`\ + (256 - a) * LS\ :sub:`a`\) / 256
+ *
+ * Where a is the @mesh_alpha_r/g/b value, and LS\ :sub:`a`\ and LS\ :sub:`b`\
+ * are the node cofficients for the two tables selected by the
+ * @mesh_alpha_bank_r/g/b value.
+ *
+ * The scale of the applied correction may also be controlled by tuning the
+ * @mesh_strength member. This is a modifier to the final coefficients which can
+ * be used to globally reduce the gains applied.
+ *
+ * header.type should be set to MALI_C55_PARAM_MESH_SHADING_SELECTION from
+ * :c:type:`mali_c55_param_block_type` for this block.
+ *
+ * @header:		The Mali-C55 parameters block header
+ * @mesh_alpha_bank_r:	Red mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_bank_g:	Green mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_bank_b:	Blue mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_r:	Blend coefficient for R [0..255]
+ * @mesh_alpha_g:	Blend coefficient for G [0..255]
+ * @mesh_alpha_b:	Blend coefficient for B [0..255]
+ * @mesh_strength:	Mesh strength in Q4.12 format [0..4096]
+ */
+struct mali_c55_params_mesh_shading_selection {
+	struct mali_c55_params_block_header header;
+	__u8 mesh_alpha_bank_r;
+	__u8 mesh_alpha_bank_g;
+	__u8 mesh_alpha_bank_b;
+	__u8 mesh_alpha_r;
+	__u8 mesh_alpha_g;
+	__u8 mesh_alpha_b;
+	__u16 mesh_strength;
+};
+
+/**
+ * define MALI_C55_PARAMS_MAX_SIZE - Maximum size of all Mali C55 Parameters
+ *
+ * Though the parameters for the Mali-C55 are passed as optional blocks, the
+ * driver still needs to know the absolute maximum size so that it can allocate
+ * a buffer sized appropriately to accommodate userspace attempting to set all
+ * possible parameters in a single frame.
+ *
+ * Some structs are in this list multiple times. Where that's the case, it just
+ * reflects the fact that the same struct can be used with multiple different
+ * header types from :c:type:`mali_c55_param_block_type`.
+ */
+#define MALI_C55_PARAMS_MAX_SIZE				\
+	(sizeof(struct mali_c55_params_sensor_off_preshading) +	\
+	sizeof(struct mali_c55_params_aexp_hist) +		\
+	sizeof(struct mali_c55_params_aexp_weights) +		\
+	sizeof(struct mali_c55_params_aexp_hist) +		\
+	sizeof(struct mali_c55_params_aexp_weights) +		\
+	sizeof(struct mali_c55_params_digital_gain) +		\
+	sizeof(struct mali_c55_params_awb_gains) +		\
+	sizeof(struct mali_c55_params_awb_config) +		\
+	sizeof(struct mali_c55_params_awb_gains) +		\
+	sizeof(struct mali_c55_params_mesh_shading_config) +	\
+	sizeof(struct mali_c55_params_mesh_shading_selection))
+
+/**
+ * struct mali_c55_params_buffer - 3A configuration parameters
+ *
+ * This struct contains the configuration parameters of the Mali-C55 ISP
+ * algorithms, serialized by userspace into a data buffer. Each configuration
+ * parameter block is represented by a block-specific structure which contains a
+ * :c:type:`mali_c55_params_block_header` entry as first member. Userspace
+ * populates the @data buffer with configuration parameters for the blocks that
+ * it intends to configure. As a consequence, the data buffer effective size
+ * changes according to the number of ISP blocks that userspace intends to
+ * configure.
+ *
+ * The parameters buffer is versioned by the @version field to allow modifying
+ * and extending its definition. Userspace shall populate the @version field to
+ * inform the driver about the version it intends to use. The driver will parse
+ * and handle the @data buffer according to the data layout specific to the
+ * indicated version and return an error if the desired version is not
+ * supported.
+ *
+ * For each ISP block that userspace wants to configure, a block-specific
+ * structure is appended to the @data buffer, one after the other without gaps
+ * in between nor overlaps. Userspace shall populate the @total_size field with
+ * the effective size, in bytes, of the @data buffer.
+ *
+ * The expected memory layout of the parameters buffer is::
+ *
+ *	+-------------------- struct mali_c55_params_buffer ------------------+
+ *	| version = MALI_C55_PARAM_BUFFER_V1;                                 |
+ *	| total_size = sizeof(struct mali_c55_params_sensor_off_preshading)   |
+ *	|              sizeof(struct mali_c55_params_aexp_hist);              |
+ *	| +------------------------- data  ---------------------------------+ |
+ *	| | +--------- struct mali_c55_params_sensor_off_preshading ------+ | |
+ *	| | | +-------- struct mali_c55_params_block_header header -----+ | | |
+ *	| | | | type = MALI_C55_PARAM_BLOCK_SENSOR_OFFS;                | | | |
+ *	| | | | flags = MALI_C55_PARAM_BLOCK_FL_NONE;                   | | | |
+ *	| | | | size =                                                  | | | |
+ *	| | | |    sizeof(struct mali_c55_params_sensor_off_preshading);| | | |
+ *	| | | +---------------------------------------------------------+ | | |
+ *	| | | chan00 = ...;                                               | | |
+ *	| | | chan01 = ...;                                               | | |
+ *	| | | chan10 = ...;                                               | | |
+ *	| | | chan11 = ...;                                               | | |
+ *	| | +------------ struct mali_c55_params_aexp_hist ---------------+ | |
+ *	| | | +-------- struct mali_c55_params_block_header header -----+ | | |
+ *	| | | | type = MALI_C55_PARAM_BLOCK_AEXP_HIST;                  | | | |
+ *	| | | | flags = MALI_C55_PARAM_BLOCK_FL_NONE;                   | | | |
+ *	| | | | size = sizeof(struct mali_c55_params_aexp_hist);        | | | |
+ *	| | | +---------------------------------------------------------+ | | |
+ *	| | | skip_x = ...;                                               | | |
+ *	| | | offset_x = ...;                                             | | |
+ *	| | | skip_y = ...;                                               | | |
+ *	| | | offset_y = ...;                                             | | |
+ *	| | | scale_bottom = ...;                                         | | |
+ *	| | | scale_top = ...;                                            | | |
+ *	| | | plane_mode = ...;                                           | | |
+ *	| | | tap_point = ...;                                            | | |
+ *	| | +-------------------------------------------------------------+ | |
+ *	| +-----------------------------------------------------------------+ |
+ *	+---------------------------------------------------------------------+
+ *
+ * @version: The version from :c:type:`mali_c55_param_buffer_version`
+ * @total_size: The Mali-C55 configuration data effective size, excluding this
+ *		header
+ * @data: The Mali-C55 configuration blocks data
+ */
+struct mali_c55_params_buffer {
+	__u8 version;
+	__u32 total_size;
+	__u8 data[MALI_C55_PARAMS_MAX_SIZE];
+};
+
 #endif /* __UAPI_MALI_C55_CONFIG_H */
