@@ -8,7 +8,7 @@ mmc_core-y := core.o bus.o host.o \
mmc.o mmc_ops.o sd.o sd_ops.o \
sdio.o sdio_ops.o sdio_bus.o \
sdio_cis.o sdio_io.o sdio_irq.o \
- slot-gpio.o regulator.o uhs2.o
+ slot-gpio.o regulator.o sd_uhs2.o
mmc_core-$(CONFIG_OF) += pwrseq.o
obj-$(CONFIG_PWRSEQ_SIMPLE) += pwrseq_simple.o
obj-$(CONFIG_PWRSEQ_SD8787) += pwrseq_sd8787.o
@@ -1349,7 +1349,7 @@ void mmc_power_up(struct mmc_host *host, u32 ocr)
host->ios.chip_select = MMC_CS_HIGH;
else
host->ios.chip_select = MMC_CS_DONTCARE;
- host->ios.timing = MMC_TIMING_SD_UHS2;
+ host->ios.timing = MMC_TIMING_UHS2;
} else {
mmc_pwrseq_pre_power_on(host);
@@ -1014,7 +1014,7 @@ static bool mmc_sd_card_using_v18(struct mmc_card *card)
* In the case of a resume, "oldcard" will contain the card
* we're trying to reinitialise.
*/
-static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
+int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
struct mmc_card *oldcard)
{
struct mmc_card *card;
@@ -9,6 +9,7 @@ extern struct device_type sd_type;
struct mmc_host;
struct mmc_card;
+int mmc_sd_init_card(struct mmc_host *host, u32 ocr, struct mmc_card *oldcard);
int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr);
int mmc_sd_get_csd(struct mmc_card *card);
void mmc_decode_cid(struct mmc_card *card);
new file mode 100644
@@ -0,0 +1,1157 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Linaro Ltd
+ *
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ *
+ * Support for SD UHS-II cards
+ */
+#include <asm/byteorder.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/core.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/slot-gpio.h>
+#include <linux/mmc/uhs2.h>
+
+#include "core.h"
+#include "bus.h"
+#include "sd_ops.h"
+#include "sd.h"
+#include "mmc_ops.h"
+#include "uhs2.h"
+
+#define DBG(f, x...) \
+ pr_warn("[%s()]: " f, __func__, ## x)
+
+//static const unsigned int sd_uhs2_freqs[] = { 52000000, 26000000 };
+
+/* This function is part of sdhci_uhs2_set_ios() in sdhci-uhs2.c
+static int sd_uhs2_set_ios(struct mmc_host *host)
+{
+ struct mmc_ios *ios = &host->ios;
+
+ return host->ops->uhs2_set_ios(host, ios);
+}
+*/
+
+/* This function is part of mmc_power_up() in core.c
+static int sd_uhs2_power_up(struct mmc_host *host)
+{
+ host->ios.vdd = fls(host->ocr_avail) - 1;
+ host->ios.clock = host->f_init;
+ host->ios.timing = MMC_TIMING_SD_UHS2;
+ host->ios.power_mode = MMC_POWER_UP;
+
+ return sd_uhs2_set_ios(host);
+}*/
+
+/* This function is part of mmc_power_off() in core.c
+static void sd_uhs2_power_off(struct mmc_host *host)
+{
+ host->ios.vdd = 0;
+ host->ios.clock = 0;
+ host->ios.timing = MMC_TIMING_LEGACY;
+ host->ios.power_mode = MMC_POWER_OFF;
+
+ sd_uhs2_set_ios(host);
+}
+*/
+
+/**
+ * uhs2_cmd_assemble - assemble and build up uhs2 command
+ * @cmd: MMC command
+ * @uhs2_cmd: UHS2 command
+ * @header: Value of packet header
+ * @arg: Argument of packet
+ * @payload: Payload of packet
+ * @plen: Payload length
+ * @resp: Buffer for response
+ * @resp_len: Response buffer length
+ *
+ * resp is inputted outside which should be a variable created by caller
+ * so caller should handle it. For SD command, there is no uhs2_resp and
+ * response should be stored in resp of mmc_command.
+ */
+static void uhs2_cmd_assemble(struct mmc_command *cmd,
+ struct uhs2_command *uhs2_cmd,
+ u16 header, u16 arg,
+ u32 *payload, u8 plen, u8 *resp, u8 resp_len)
+{
+ uhs2_cmd->header = header;
+ uhs2_cmd->arg = arg;
+ uhs2_cmd->payload = payload;
+ uhs2_cmd->payload_len = plen * sizeof(u32);
+ uhs2_cmd->packet_len = uhs2_cmd->payload_len + 4;
+
+ cmd->uhs2_cmd = uhs2_cmd;
+ cmd->uhs2_resp = resp;
+ cmd->uhs2_resp_len = resp_len;
+
+ pr_debug("%s: uhs2_cmd: header=0x%x arg=0x%x\n",
+ __func__, uhs2_cmd->header, uhs2_cmd->arg);
+ pr_debug("%s: payload_len=%d packet_len=%d resp_len=%d\n",
+ __func__, uhs2_cmd->payload_len, uhs2_cmd->packet_len,
+ cmd->uhs2_resp_len);
+}
+
+/*
+ * Do the early initialization of the card, by sending the device init broadcast
+ * command and wait for the process to be completed.
+ */
+static int sd_uhs2_dev_init(struct mmc_host *host)
+{
+ struct mmc_command cmd = {0};
+ struct uhs2_command uhs2_cmd = {};
+ u32 cnt;
+ u32 dap, gap, gap1;
+ u16 header = 0, arg = 0;
+ u32 payload[1];
+ u8 plen = 1;
+ u8 gd = 0, cf = 1;
+ u8 resp[6] = {0};
+ u8 resp_len = 6;
+ int err;
+
+ dap = host->uhs2_caps.dap;
+ gap = host->uhs2_caps.gap;
+
+ header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD;
+ arg = ((UHS2_DEV_CMD_DEVICE_INIT & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_4B |
+ (UHS2_DEV_CMD_DEVICE_INIT >> 8);
+
+ /* need this for some cards */
+ cmd.busy_timeout = 1000;
+
+ for (cnt = 0; cnt < 30; cnt++) {
+ payload[0] = ((dap & 0xF) << 12) |
+ (cf << 11) |
+ ((gd & 0xF) << 4) |
+ (gap & 0xF);
+
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg,
+ payload, plen, resp, resp_len);
+
+ DBG("Begin DEVICE_INIT, header=0x%x, arg=0x%x, payload=0x%x.\n",
+ header, arg, payload[0]);
+
+ DBG("Sending DEVICE_INIT. Count = %d\n", cnt);
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (IS_ENABLED(CONFIG_MMC_DEBUG)) {
+ int i;
+
+ pr_warn("%s: DEVICE_INIT response is: ",
+ mmc_hostname(host));
+ for (i = 0; i < resp_len; i++)
+ pr_warn("0x%x ", resp[i]);
+ pr_warn("\n");
+ }
+
+ if (resp[3] != (UHS2_DEV_CMD_DEVICE_INIT & 0xFF)) {
+ pr_err("%s: DEVICE_INIT response is wrong!\n",
+ mmc_hostname(host));
+ return -EIO;
+ }
+
+ if (resp[5] & 0x8) {
+ DBG("CF is set, device is initialized!\n");
+ host->group_desc = gd;
+ break;
+ }
+ gap1 = resp[4] & 0x0F;
+ if (gap == gap1)
+ gd++;
+ }
+ if (cnt == 30) {
+ pr_err("%s: DEVICE_INIT fail, already 30 times!\n",
+ mmc_hostname(host));
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/*
+ * Run the enumeration process by sending the enumerate command to the card.
+ * Note that, we currently support only the point to point connection, which
+ * means only one card can be attached per host/slot.
+ */
+//static int sd_uhs2_enum(struct mmc_host *host, u32 *node_id) // node_id had been saved in host->uhs2_dev_prop.node_id
+static int sd_uhs2_enum(struct mmc_host *host)
+{
+ struct mmc_command cmd = {0};
+ struct uhs2_command uhs2_cmd = {};
+ u16 header = 0, arg = 0;
+ u32 payload[1];
+ u8 plen = 1;
+ u8 id_f = 0xF, id_l = 0x0;
+ u8 resp[8] = {0};
+ u8 resp_len = 8;
+ int err;
+
+ header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD;
+ arg = ((UHS2_DEV_CMD_ENUMERATE & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_4B |
+ (UHS2_DEV_CMD_ENUMERATE >> 8);
+
+ payload[0] = (id_f << 4) | id_l;
+
+ DBG("Begin ENUMERATE, header=0x%x, arg=0x%x, payload=0x%x.\n",
+ header, arg, payload[0]);
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, plen,
+ resp, resp_len);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (IS_ENABLED(CONFIG_MMC_DEBUG)) {
+ int i;
+
+ pr_warn("%s: ENUMERATE response is: ", mmc_hostname(host));
+ for (i = 0; i < resp_len; i++)
+ pr_warn("0x%x ", resp[i]);
+ pr_warn("\n");
+ }
+
+ if (resp[3] != (UHS2_DEV_CMD_ENUMERATE & 0xFF)) {
+ pr_err("%s: ENUMERATE response is wrong!\n",
+ mmc_hostname(host));
+ return -EIO;
+ }
+
+ id_f = (resp[4] >> 4) & 0xF;
+ id_l = resp[4] & 0xF;
+ DBG("id_f = %d, id_l = %d.\n", id_f, id_l);
+ DBG("Enumerate Cmd Completed. No. of Devices connected = %d\n",
+ id_l - id_f + 1);
+ host->uhs2_dev_prop.node_id = id_f;
+
+ return 0;
+}
+
+/*
+ * Read the UHS-II configuration registers (CFG_REG) of the card, by sending it
+ * commands and by parsing the responses. Store a copy of the relevant data in
+ * card->uhs2_config.
+ */
+//static int sd_uhs2_config_read(struct mmc_host *host, struct mmc_card *card)
+static int sd_uhs2_config_read(struct mmc_host *host)
+{
+ struct mmc_command cmd = {0};
+ struct uhs2_command uhs2_cmd = {};
+ u16 header = 0, arg = 0;
+ u32 cap;
+ int err;
+
+ DBG("INQUIRY_CFG: read Generic Caps.\n");
+ header = UHS2_NATIVE_PACKET |
+ UHS2_PACKET_TYPE_CCMD |
+ host->uhs2_dev_prop.node_id;
+ arg = ((UHS2_DEV_CONFIG_GEN_CAPS & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_READ |
+ UHS2_NATIVE_CMD_PLEN_4B |
+ (UHS2_DEV_CONFIG_GEN_CAPS >> 8);
+
+ DBG("Begin INQUIRY_CFG, header=0x%x, arg=0x%x.\n",
+ header, arg);
+ /* There is no payload because per spec, there should be
+ * no payload field for read CCMD.
+ * Plen is set in arg. Per spec, plen for read CCMD
+ * represents the len of read data which is assigned in payload
+ * of following RES (p136).
+ */
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (IS_ENABLED(CONFIG_MMC_DEBUG)) {
+ int i;
+
+ pr_warn("%s: INQUIRY_CFG generic response is: ",
+ mmc_hostname(host));
+ for (i = 0; i < 2; i++)
+ pr_warn("0x%x ", cmd.resp[i]);
+ pr_warn("\n");
+ }
+
+ cap = cmd.resp[0];
+ DBG("Device Generic Caps (0-31) is: 0x%x.\n", cap);
+ host->uhs2_dev_prop.n_lanes = (cap >> UHS2_DEV_CONFIG_N_LANES_POS) &
+ UHS2_DEV_CONFIG_N_LANES_MASK;
+ host->uhs2_dev_prop.dadr_len = (cap >> UHS2_DEV_CONFIG_DADR_POS) &
+ UHS2_DEV_CONFIG_DADR_MASK;
+ host->uhs2_dev_prop.app_type = (cap >> UHS2_DEV_CONFIG_APP_POS) &
+ UHS2_DEV_CONFIG_APP_MASK;
+
+ DBG("INQUIRY_CFG: read PHY Caps.\n");
+ arg = ((UHS2_DEV_CONFIG_PHY_CAPS & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_READ |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_PHY_CAPS >> 8);
+
+ DBG("Begin INQUIRY_CFG, header=0x%x, arg=0x%x.\n",
+ header, arg);
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (IS_ENABLED(CONFIG_MMC_DEBUG)) {
+ int i;
+
+ pr_warn("%s: INQUIRY_CFG PHY response is: ",
+ mmc_hostname(host));
+ for (i = 0; i < 2; i++)
+ pr_warn("0x%x ", cmd.resp[i]);
+ pr_warn("\n");
+ }
+
+ cap = cmd.resp[0];
+ DBG("Device PHY Caps (0-31) is: 0x%x.\n", cap);
+ host->uhs2_dev_prop.phy_minor_rev = cap &
+ UHS2_DEV_CONFIG_PHY_MINOR_MASK;
+ host->uhs2_dev_prop.phy_major_rev = (cap >>
+ UHS2_DEV_CONFIG_PHY_MAJOR_POS) &
+ UHS2_DEV_CONFIG_PHY_MAJOR_MASK;
+ host->uhs2_dev_prop.can_hibernate = (cap >>
+ UHS2_DEV_CONFIG_CAN_HIBER_POS) &
+ UHS2_DEV_CONFIG_CAN_HIBER_MASK;
+
+ cap = cmd.resp[1];
+ DBG("Device PHY Caps (32-63) is: 0x%x.\n", cap);
+ host->uhs2_dev_prop.n_lss_sync = cap & UHS2_DEV_CONFIG_N_LSS_SYN_MASK;
+ host->uhs2_dev_prop.n_lss_dir = (cap >>
+ UHS2_DEV_CONFIG_N_LSS_DIR_POS) &
+ UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
+ if (host->uhs2_dev_prop.n_lss_sync == 0)
+ host->uhs2_dev_prop.n_lss_sync = 16 << 2;
+ else
+ host->uhs2_dev_prop.n_lss_sync <<= 2;
+
+ if (host->uhs2_dev_prop.n_lss_dir == 0)
+ host->uhs2_dev_prop.n_lss_dir = 16 << 3;
+ else
+ host->uhs2_dev_prop.n_lss_dir <<= 3;
+
+ DBG("INQUIRY_CFG: read LINK-TRAN Caps.\n");
+ arg = ((UHS2_DEV_CONFIG_LINK_TRAN_CAPS & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_READ |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_LINK_TRAN_CAPS >> 8);
+
+ DBG("Begin INQUIRY_CFG, header=0x%x, arg=0x%x.\n",
+ header, arg);
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, NULL, 0, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (IS_ENABLED(CONFIG_MMC_DEBUG)) {
+ int i;
+
+ pr_warn("%s: INQUIRY_CFG Link-Tran response is: ",
+ mmc_hostname(host));
+ for (i = 0; i < 2; i++)
+ pr_warn("0x%x ", cmd.resp[i]);
+ pr_warn("\n");
+ }
+
+ cap = cmd.resp[0];
+ DBG("Device LINK-TRAN Caps (0-31) is: 0x%x.\n", cap);
+ host->uhs2_dev_prop.link_minor_rev = cap &
+ UHS2_DEV_CONFIG_LT_MINOR_MASK;
+ host->uhs2_dev_prop.link_major_rev = (cap >>
+ UHS2_DEV_CONFIG_LT_MAJOR_POS) &
+ UHS2_DEV_CONFIG_LT_MAJOR_MASK;
+ host->uhs2_dev_prop.n_fcu = (cap >> UHS2_DEV_CONFIG_N_FCU_POS) &
+ UHS2_DEV_CONFIG_N_FCU_MASK;
+ host->uhs2_dev_prop.dev_type = (cap >> UHS2_DEV_CONFIG_DEV_TYPE_POS) &
+ UHS2_DEV_CONFIG_DEV_TYPE_MASK;
+ host->uhs2_dev_prop.maxblk_len = (cap >>
+ UHS2_DEV_CONFIG_MAX_BLK_LEN_POS) &
+ UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK;
+
+ cap = cmd.resp[1];
+ DBG("Device LINK-TRAN Caps (32-63) is: 0x%x.\n", cap);
+ host->uhs2_dev_prop.n_data_gap = cap & UHS2_DEV_CONFIG_N_DATA_GAP_MASK;
+ if (host->uhs2_dev_prop.n_fcu == 0)
+ host->uhs2_dev_prop.n_fcu = 256;
+
+ return 0;
+}
+
+/*
+ * Based on the card's and host's UHS-II capabilities, let's update the
+ * configuration of the card and the host. This may also include to move to a
+ * greater speed range/mode. Depending on the updated configuration, we may need
+ * to do a soft reset of the card via sending it a GO_DORMANT_STATE command.
+ *
+ * In the final step, let's check if the card signals "config completion", which
+ * indicates that the card has moved from config state into active state.
+ */
+//static int sd_uhs2_config_write(struct mmc_host *host, struct mmc_card *card)
+static int sd_uhs2_config_write(struct mmc_host *host)
+{
+ struct mmc_command cmd = {0};
+ struct uhs2_command uhs2_cmd = {};
+ u16 header = 0, arg = 0;
+ u32 nTry;
+ u32 payload[2];
+ u8 nMinDataGap;
+ u8 plen;
+ int err;
+ u8 resp[5] = {0};
+ u8 resp_len = 5;
+ /*
+ * must long enough for RECV_SW_DIR == 2;
+ * need lss_dir at least 4 for GL9755 device
+ * max compitable gLssDir = 0
+ */
+ u32 gLssDir = 0;
+
+ DBG("SET_COMMON_CFG: write Generic Settings.\n");
+ header = UHS2_NATIVE_PACKET |
+ UHS2_PACKET_TYPE_CCMD | host->uhs2_dev_prop.node_id;
+ arg = ((UHS2_DEV_CONFIG_GEN_SET & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_GEN_SET >> 8);
+
+ if (host->uhs2_dev_prop.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD &&
+ host->uhs2_caps.n_lanes == UHS2_DEV_CONFIG_2L_HD_FD) {
+ /* Support HD */
+ DBG("Both Host and device support 2L-HD.\n");
+ host->flags |= MMC_UHS2_2L_HD;
+ host->uhs2_caps.n_lanes_set = UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
+ host->uhs2_dev_prop.n_lanes_set =
+ UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
+ nMinDataGap = 1;
+ } else {
+ /* Only support 2L-FD so far */
+ host->flags &= ~MMC_UHS2_2L_HD;
+ host->uhs2_caps.n_lanes_set = UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
+ host->uhs2_dev_prop.n_lanes_set =
+ UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD;
+ nMinDataGap = 3;
+ }
+
+ plen = 2;
+ payload[0] = host->uhs2_dev_prop.n_lanes_set <<
+ UHS2_DEV_CONFIG_N_LANES_POS;
+ payload[1] = 0;
+ payload[0] = cpu_to_be32(payload[0]);
+ payload[1] = cpu_to_be32(payload[1]);
+
+ DBG("Begin SET_COMMON_CFG, header=0x%x, arg=0x%x\n", header, arg);
+ DBG("UHS2 write Generic Settings %08x %08x\n",
+ payload[0], payload[1]);
+ DBG("flags=%08x dev_prop.n_lanes_set=%x host_caps.n_lanes_set=%x\n",
+ host->flags,
+ host->uhs2_dev_prop.n_lanes_set,
+ host->uhs2_caps.n_lanes_set);
+
+ /*
+ * There is no payload because per spec, there should be
+ * no payload field for read CCMD.
+ * Plen is set in arg. Per spec, plen for read CCMD
+ * represents the len of read data which is assigned in payload
+ * of following RES (p136).
+ */
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, plen, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ DBG("SET_COMMON_CFG: PHY Settings.\n");
+ arg = ((UHS2_DEV_CONFIG_PHY_SET & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_PHY_SET >> 8);
+
+ for (nTry = 0; nTry < 2; nTry++) {
+ plen = 2;
+
+ if (host->uhs2_caps.speed_range ==
+ UHS2_DEV_CONFIG_PHY_SET_SPEED_B) {
+ host->flags |= MMC_UHS2_SPEED_B;
+ host->uhs2_dev_prop.speed_range_set =
+ UHS2_DEV_CONFIG_PHY_SET_SPEED_B;
+ DBG("set dev_prop.speed_range_set to SPEED_B\n");
+ } else {
+ host->uhs2_dev_prop.speed_range_set =
+ UHS2_DEV_CONFIG_PHY_SET_SPEED_A;
+ host->flags &= ~MMC_UHS2_SPEED_B;
+ DBG("set dev_prop.speed_range_set to SPEED_A\n");
+ }
+
+ payload[0] = host->uhs2_dev_prop.speed_range_set <<
+ UHS2_DEV_CONFIG_PHY_SET_SPEED_POS;
+
+ host->uhs2_dev_prop.n_lss_sync_set =
+ (min(host->uhs2_dev_prop.n_lss_sync,
+ host->uhs2_caps.n_lss_sync) >> 2) &
+ UHS2_DEV_CONFIG_N_LSS_SYN_MASK;
+ host->uhs2_caps.n_lss_sync_set =
+ host->uhs2_dev_prop.n_lss_sync_set;
+
+ if (nTry) {
+ host->uhs2_dev_prop.n_lss_dir_set =
+ (max(host->uhs2_dev_prop.n_lss_dir,
+ host->uhs2_caps.n_lss_dir) >> 3) &
+ UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
+ host->uhs2_caps.n_lss_dir_set =
+ host->uhs2_dev_prop.n_lss_dir_set;
+ payload[1] = (host->uhs2_dev_prop.n_lss_dir_set <<
+ UHS2_DEV_CONFIG_N_LSS_DIR_POS) |
+ host->uhs2_dev_prop.n_lss_sync_set;
+ } else {
+ host->uhs2_caps.n_lss_dir_set =
+ (host->uhs2_dev_prop.n_lss_dir >> 3) &
+ UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
+ host->uhs2_dev_prop.n_lss_dir_set =
+ ((host->uhs2_caps.n_lss_dir >> 3) + 1) &
+ UHS2_DEV_CONFIG_N_LSS_DIR_MASK;
+ }
+
+ if (!gLssDir) {
+ host->uhs2_dev_prop.n_lss_dir_set = 0;
+ } else {
+ host->uhs2_dev_prop.n_lss_dir_set =
+ max((u8)gLssDir,
+ host->uhs2_dev_prop.n_lss_dir_set);
+ }
+
+ payload[1] = (host->uhs2_dev_prop.n_lss_dir_set <<
+ UHS2_DEV_CONFIG_N_LSS_DIR_POS) |
+ host->uhs2_dev_prop.n_lss_sync_set;
+ payload[0] = cpu_to_be32(payload[0]);
+ payload[1] = cpu_to_be32(payload[1]);
+
+ DBG("UHS2 SET PHY Settings %08x %08x\n",
+ payload[0], payload[1]);
+ DBG("host->flags=%08x dev_prop.speed_range_set=%x\n",
+ host->flags,
+ host->uhs2_dev_prop.speed_range_set);
+ DBG("dev_prop.n_lss_sync_set=%x host_caps.n_lss_sync_set=%x\n",
+ host->uhs2_dev_prop.n_lss_sync_set,
+ host->uhs2_caps.n_lss_sync_set);
+ DBG("dev_prop.n_lss_dir_set=%x host_caps.n_lss_dir_set=%x\n",
+ host->uhs2_dev_prop.n_lss_dir_set,
+ host->uhs2_caps.n_lss_dir_set);
+
+ DBG("Begin SET_COMMON_CFG header=0x%x arg=0x%x\n",
+ header, arg);
+ DBG("\t\tpayload[0]=0x%x payload[1]=0x%x\n",
+ payload[0], payload[1]);
+
+ resp_len = 4;
+ memset(resp, 0, sizeof(resp));
+
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg,
+ payload, plen, resp, resp_len);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ if (!(resp[2] & 0x80))
+ break;
+
+ DBG("%s: %s: UHS2 SET PHY Settings fail, res= 0x%x!\n",
+ mmc_hostname(host), __func__, resp[2]);
+ }
+
+ DBG("SET_COMMON_CFG: LINK-TRAN Settings.\n");
+ arg = ((UHS2_DEV_CONFIG_LINK_TRAN_SET & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_LINK_TRAN_SET >> 8);
+
+ plen = 2;
+
+ if (host->uhs2_dev_prop.app_type == UHS2_DEV_CONFIG_APP_SD_MEM)
+ host->uhs2_dev_prop.maxblk_len_set =
+ UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN;
+ else
+ host->uhs2_dev_prop.maxblk_len_set =
+ min(host->uhs2_dev_prop.maxblk_len,
+ host->uhs2_caps.maxblk_len);
+ host->uhs2_caps.maxblk_len_set = host->uhs2_dev_prop.maxblk_len_set;
+
+ host->uhs2_dev_prop.n_fcu_set =
+ min(host->uhs2_dev_prop.n_fcu,
+ host->uhs2_caps.n_fcu);
+ host->uhs2_caps.n_fcu_set = host->uhs2_dev_prop.n_fcu_set;
+
+ host->uhs2_dev_prop.n_data_gap_set =
+ max(nMinDataGap, host->uhs2_dev_prop.n_data_gap);
+
+ host->uhs2_caps.n_data_gap_set = host->uhs2_dev_prop.n_data_gap_set;
+
+ host->uhs2_caps.max_retry_set = 3;
+ host->uhs2_dev_prop.max_retry_set = host->uhs2_caps.max_retry_set;
+
+ payload[0] = (host->uhs2_dev_prop.maxblk_len_set <<
+ UHS2_DEV_CONFIG_MAX_BLK_LEN_POS) |
+ (host->uhs2_dev_prop.max_retry_set <<
+ UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS) |
+ (host->uhs2_dev_prop.n_fcu_set <<
+ UHS2_DEV_CONFIG_N_FCU_POS);
+ payload[1] = host->uhs2_dev_prop.n_data_gap_set;
+ payload[0] = cpu_to_be32(payload[0]);
+ payload[1] = cpu_to_be32(payload[1]);
+
+ DBG("Begin SET_COMMON_CFG header=0x%x arg=0x%x\n", header, arg);
+ DBG("\t\tpayload[0]=0x%x payload[1]=0x%x\n", payload[0], payload[1]);
+
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, plen, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ DBG("SET_COMMON_CFG: Set Config Completion.\n");
+ arg = ((UHS2_DEV_CONFIG_GEN_SET & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_8B |
+ (UHS2_DEV_CONFIG_GEN_SET >> 8);
+
+ plen = 2;
+ payload[0] = 0;
+ payload[1] = UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE;
+ payload[0] = cpu_to_be32(payload[0]);
+ payload[1] = cpu_to_be32(payload[1]);
+
+ DBG("Begin SET_COMMON_CFG, header=0x%x, arg=0x%x, payload[0] = 0x%x.\n",
+ header, arg, payload[0]);
+ resp_len = 5;
+ memset(resp, 0, sizeof(resp));
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, plen,
+ resp, resp_len);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ /* Set host Config Setting registers */
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, SET_CONFIG)) {
+ pr_err("%s: %s: UHS2 SET_CONFIG fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int uhs2_go_dormant(struct mmc_host *host, bool hibernate)
+{
+ struct mmc_command cmd = {0};
+ struct uhs2_command uhs2_cmd = {};
+ u16 header = 0, arg = 0;
+ u32 payload[1];
+ u8 plen = 1;
+ int err;
+
+ /* Disable Normal INT */
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, DISABLE_INT)) {
+ pr_err("%s: %s: UHS2 DISABLE_INT fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ header = UHS2_NATIVE_PACKET | UHS2_PACKET_TYPE_CCMD |
+ host->uhs2_dev_prop.node_id;
+
+ arg = ((UHS2_DEV_CMD_GO_DORMANT_STATE & 0xFF) << 8) |
+ UHS2_NATIVE_CMD_WRITE |
+ UHS2_NATIVE_CMD_PLEN_4B |
+ (UHS2_DEV_CMD_GO_DORMANT_STATE >> 8);
+
+ if (hibernate)
+ payload[0] = UHS2_DEV_CMD_DORMANT_HIBER;
+
+ DBG("Begin GO_DORMANT_STATE, header=0x%x, arg=0x%x, payload=0x%x.\n",
+ header, arg, payload[0]);
+ uhs2_cmd_assemble(&cmd, &uhs2_cmd, header, arg, payload, plen, NULL, 0);
+
+ err = mmc_wait_for_cmd(host, &cmd, 0);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD send fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ /* Check Dormant State in Present */
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, CHECK_DORMANT)) {
+ pr_err("%s: %s: UHS2 GO_DORMANT_STATE fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ if (host->ops->uhs2_disable_clk)
+ host->ops->uhs2_disable_clk(host);
+
+ return 0;
+}
+
+static int uhs2_change_speed(struct mmc_host *host)
+{
+ int err;
+
+ /* Change Speed Range */
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, SET_SPEED_B)) {
+ pr_err("%s: %s: UHS2 SET_SPEED fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ err = uhs2_go_dormant(host, false);
+ if (err) {
+ pr_err("%s: %s: UHS2 GO_DORMANT_STATE fail, err= 0x%x!\n",
+ mmc_hostname(host), __func__, err);
+ return -EIO;
+ }
+
+ /* restore sd clock */
+ mdelay(5);
+ if (host->ops->uhs2_enable_clk)
+ host->ops->uhs2_enable_clk(host);
+
+ /* Enable Normal INT */
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, ENABLE_INT)) {
+ pr_err("%s: %s: UHS2 ENABLE_INT fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ if (!host->ops->uhs2_detect_init ||
+ host->ops->uhs2_detect_init(host)) {
+ pr_err("%s: %s: uhs2_detect_init() fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/*
+ * Initialize the UHS-II card through the SD-TRAN transport layer. This enables
+ * commands/requests to be backwards compatible through the legacy SD protocol.
+ * UHS-II cards has a specific power limit specified for VDD1/VDD2, that should
+ * be set through a legacy CMD6. Note that, the power limit that becomes set,
+ * survives a soft reset through the GO_DORMANT_STATE command.
+ */
+static int sd_uhs2_legacy_init(struct mmc_host *host)
+{
+ int err;
+ u32 ocr, rocr;
+
+ WARN_ON(!host->claimed);
+
+ // Jason test
+ mmc_go_idle(host);
+ mmc_delay(10);
+
+ err = mmc_send_if_cond(host, host->ocr_avail);
+ if (err) {
+ pr_err("%s: %s: UHS2 CMD8 fail!\n", mmc_hostname(host), __func__);
+ //return err;
+ }
+
+ err = mmc_send_app_op_cond(host, 0, &ocr);
+ if (err)
+ return err;
+
+ if (host->ocr_avail_sd)
+ host->ocr_avail = host->ocr_avail_sd;
+
+ /*
+ * Some SD cards claims an out of spec VDD voltage range. Let's treat
+ * these bits as being in-valid and especially also bit7.
+ */
+ ocr &= ~0x7FFF;
+
+ rocr = mmc_select_voltage(host, ocr);
+
+ /*
+ * Some cards have zero value of rocr in UHS-II mode. Assign host's ocr
+ * value to rocr.
+ */
+ if (!rocr)
+ rocr = host->ocr_avail;
+
+ /*
+ * Can we support the voltage(s) of the card(s)?
+ */
+ if (!rocr) {
+ pr_err("%s: UHS2: there is no valid OCR.\n", mmc_hostname(host));
+ return -EINVAL;
+ }
+
+ /*
+ * Detect and init the card.
+ */
+ err = mmc_sd_init_card(host, rocr, NULL);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+/*
+ * Run the phy initialization sequence, which mainly relies on the UHS-II host
+ * to check that we reach the expected electrical state, between the host and
+ * the card.
+ */
+static int sd_uhs2_phy_init(struct mmc_host *host)
+{
+ if (!host->ops->uhs2_detect_init ||
+ host->ops->uhs2_detect_init(host)) {
+ pr_err("%s: fail to detect UHS2!\n", mmc_hostname(host));
+ return UHS2_PHY_INIT_ERR;
+ }
+ return 0;
+}
+
+static void sd_uhs2_remove(struct mmc_host *host)
+{
+ mmc_remove_card(host->card);
+ host->card = NULL;
+}
+
+static int sd_uhs2_alive(struct mmc_host *host)
+{
+ return mmc_send_status(host->card, NULL);
+}
+
+static void sd_uhs2_detect(struct mmc_host *host)
+{
+ int err;
+
+ mmc_get_card(host->card, NULL);
+ err = _mmc_detect_card_removed(host);
+ mmc_put_card(host->card, NULL);
+
+ if (err) {
+ sd_uhs2_remove(host);
+
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+ mmc_power_off(host);
+ mmc_release_host(host);
+ }
+}
+
+static int sd_uhs2_suspend(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_resume(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_runtime_suspend(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_runtime_resume(struct mmc_host *host)
+{
+ return 0;
+}
+
+static int sd_uhs2_shutdown(struct mmc_host *host)
+{
+ return 0;
+}
+
+
+/**
+ * sd_uhs2_hw_reset - invoke SW reset
+ * @host: MMC host
+ *
+ * Invoke SW reset, depending on a bit in @mask and wait for completion.
+ */
+static int sd_uhs2_hw_reset(struct mmc_host *host)
+{
+ int err = 0;
+
+ if (!host->ops->uhs2_set_reg ||
+ host->ops->uhs2_set_reg(host, UHS2_SW_RESET)) {
+ pr_err("%s: %s: UHS2_SW_RESET fail!\n",
+ mmc_hostname(host), __func__);
+ return -EIO;
+ }
+
+ return err;
+}
+
+static int sd_uhs2_attach(struct mmc_host *host)
+{
+ int err;
+
+ err = sd_uhs2_phy_init(host);
+ if (err)
+ return err;
+
+ err = sd_uhs2_init_card(host);
+ if (err)
+ return err;
+
+ mmc_release_host(host);
+ err = mmc_add_card(host->card);
+ if (err) {
+ mmc_remove_card(host->card);
+ host->card = NULL;
+ mmc_detach_bus(host);
+ mmc_claim_host(host);
+ return err;;
+ }
+
+ mmc_claim_host(host);
+
+ /* TODO: Is this the right place? */
+ if (host->ops->uhs2_post_attach_sd)
+ host->ops->uhs2_post_attach_sd(host);
+
+ return 0;
+}
+
+/**
+ * uhs2_prepare_sd_cmd - prepare for SD command packet
+ * @host: MMC host
+ * @mrq: MMC request
+ *
+ * Initialize and fill in a header and a payload of SD command packet.
+ * The caller should allocate uhs2_command in host->cmd->uhs2_cmd in
+ * advance.
+ *
+ * Return: 0 on success, non-zero error on failure
+ */
+int uhs2_prepare_sd_cmd(struct mmc_host *host, struct mmc_request *mrq)
+{
+ struct mmc_command *cmd;
+ struct uhs2_command *uhs2_cmd;
+ u16 header = 0, arg = 0;
+ u32 *payload;
+ u8 plen = 0;
+
+ cmd = mrq->cmd;
+ header = host->uhs2_dev_prop.node_id;
+ if ((cmd->flags & MMC_CMD_MASK) == MMC_CMD_ADTC)
+ header |= UHS2_PACKET_TYPE_DCMD;
+ else
+ header |= UHS2_PACKET_TYPE_CCMD;
+
+ arg = cmd->opcode << UHS2_SD_CMD_INDEX_POS;
+ if (host->flags & MMC_UHS2_APP_CMD) {
+ arg |= UHS2_SD_CMD_APP;
+ host->flags &= ~MMC_UHS2_APP_CMD;
+ }
+
+ uhs2_cmd = cmd->uhs2_cmd;
+ payload = uhs2_cmd->payload;
+ plen = 2; /* at the maximum */
+
+ if ((cmd->flags & MMC_CMD_MASK) == MMC_CMD_ADTC &&
+ !cmd->uhs2_tmode0_flag) {
+ if (host->flags & MMC_UHS2_2L_HD)
+ arg |= UHS2_DCMD_2L_HD_MODE;
+
+ arg |= UHS2_DCMD_LM_TLEN_EXIST;
+
+ if (cmd->data->blocks == 1 &&
+ cmd->data->blksz != 512 &&
+ cmd->opcode != MMC_READ_SINGLE_BLOCK &&
+ cmd->opcode != MMC_WRITE_BLOCK) {
+ arg |= UHS2_DCMD_TLUM_BYTE_MODE;
+ payload[1] = uhs2_dcmd_convert_msb(cmd->data->blksz);
+ } else {
+ payload[1] = uhs2_dcmd_convert_msb(cmd->data->blocks);
+ }
+
+ if (cmd->opcode == SD_IO_RW_EXTENDED) {
+ arg &= ~(UHS2_DCMD_LM_TLEN_EXIST |
+ UHS2_DCMD_TLUM_BYTE_MODE |
+ UHS2_NATIVE_DCMD_DAM_IO);
+ payload[1] = 0;
+ plen = 1;
+ }
+ } else {
+ plen = 1;
+ }
+
+ payload[0] = uhs2_dcmd_convert_msb(cmd->arg);
+ pr_debug("%s: %s: sd_cmd->arg = 0x%x, payload[0]= 0x%x.\n",
+ mmc_hostname(host), __func__, cmd->arg, payload[0]);
+
+ uhs2_cmd_assemble(cmd, uhs2_cmd, header, arg, payload, plen, NULL, 0);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(uhs2_prepare_sd_cmd);
+
+static const struct mmc_bus_ops sd_uhs2_ops = {
+ .remove = sd_uhs2_remove,
+ .alive = sd_uhs2_alive,
+ .detect = sd_uhs2_detect,
+ .suspend = sd_uhs2_suspend,
+ .resume = sd_uhs2_resume,
+ .runtime_suspend = sd_uhs2_runtime_suspend,
+ .runtime_resume = sd_uhs2_runtime_resume,
+ .shutdown = sd_uhs2_shutdown,
+ .hw_reset = sd_uhs2_hw_reset,
+};
+
+/*
+ * Allocate the data structure for the mmc_card and run the UHS-II specific
+ * initialization sequence.
+ */
+int sd_uhs2_init_card(struct mmc_host *host)
+{
+// struct mmc_card *card;
+// u32 node_id;
+ int err = -EIO;
+
+ if (sd_uhs2_dev_init(host)) {
+ pr_err("%s: UHS2 DEVICE_INIT fail!\n", mmc_hostname(host));
+ return err;
+ }
+
+ if (sd_uhs2_enum(host))
+ {
+ pr_err("%s: UHS2 ENUMERATE fail!\n", mmc_hostname(host));
+ return err;
+ }
+
+ if (sd_uhs2_config_read(host)) {
+ pr_err("%s: UHS2 INQUIRY_CONFIG fail!\n", mmc_hostname(host));
+ return err;
+ }
+
+ if (sd_uhs2_config_write(host)) {
+ pr_err("%s: UHS2 SET_COMMON_CONFIG fail!\n", mmc_hostname(host));
+ return err;
+ }
+
+ mmc_delay(10);
+
+ /* Change to Speed Range B if it is supported */
+ if (host->flags & MMC_UHS2_SPEED_B) {
+ if (uhs2_change_speed(host)) {
+ pr_err("%s: UHS2 uhs2_change_speed() fail!\n",
+ mmc_hostname(host));
+ return err;
+ }
+ }
+
+ host->flags |= MMC_UHS2_INITIALIZED;
+
+ mmc_attach_bus(host, &sd_uhs2_ops);
+
+ if (sd_uhs2_legacy_init(host)) {
+ pr_err("%s: sd_uhs2_legacy_init: error %d.\n", mmc_hostname(host), err);
+ mmc_detach_bus(host);
+ return err;
+ }
+
+ return 0;
+}
+
+/**
+ * mmc_uhs2_rescan_try_freq - select UHS2 interface
+ * @host: MMC host
+ * @freq: Bus speed
+ *
+ * Try to select UHS2 interface and initialize the bus for a given
+ * frequency, @freq.
+ *
+ * Return: 0 on success, non-zero error on failure
+ */
+int mmc_uhs2_rescan_try_freq(struct mmc_host *host, unsigned int freq)
+{
+ int err = -EIO;
+
+ host->flags |= MMC_UHS2_SUPPORT;
+ host->f_init = freq;
+
+ pr_debug("%s: %s: trying to init card at %u Hz\n",
+ mmc_hostname(host), __func__, host->f_init);
+
+ if (!(host->caps2 & MMC_CAP2_NO_SDIO))
+ pr_info("mmc_attach_sdio\n");
+ if (!(host->caps2 & MMC_CAP2_NO_SD))
+ pr_info("mmc_attach_sd\n");
+
+ mmc_power_up(host, 0);
+
+ err = sd_uhs2_attach(host);
+ if (err) {
+ pr_err("%s: sd_uhs2_attach fail!\n", mmc_hostname(host));
+ goto init_fail;
+ }
+ else
+ return 0;
+
+//--------------------------------------------------------------------------------------
+
+init_fail:
+ mmc_power_off(host);
+ if (host->flags & MMC_UHS2_INITIALIZED)
+ host->flags &= ~MMC_UHS2_INITIALIZED;
+ host->flags &= ~MMC_UHS2_SUPPORT;
+
+ return err;
+}
+EXPORT_SYMBOL_GPL(mmc_uhs2_rescan_try_freq);
@@ -16,6 +16,7 @@
#define UHS2_PHY_INIT_ERR 1
int mmc_uhs2_rescan_try_freq(struct mmc_host *host, unsigned int freq);
+int sd_uhs2_init_card(struct mmc_host *host);
int uhs2_prepare_sd_cmd(struct mmc_host *host, struct mmc_request *mrq);
#endif /* MMC_UHS2_H */
@@ -545,6 +545,10 @@ static int sdhci_uhs2_set_reg(struct mmc_host *mmc, enum uhs2_act act)
case CHECK_DORMANT:
err = sdhci_uhs2_check_dormant(host);
break;
+ case UHS2_SW_RESET:
+ sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_FULL);
+ /* FIXED IT : Modify return type of sdhci_uhs2_reset()? */
+ err = 0;
+ break;
default:
pr_err("%s: input action %d is wrong!\n",
mmc_hostname(host->mmc), act);
@@ -189,6 +189,7 @@ enum uhs2_act {
DISABLE_INT,
SET_SPEED_B,
CHECK_DORMANT,
+ UHS2_SW_RESET,
};
/* UHS-II Device Registers */
1. mmc: core: core.c: Modify definition name from MMC_TIMING_UHS2 to MMC_TIMING_SD_UHS2. 2. mmc: core: bus.c: Apply Ulf's coding style to function mmc_add_card(). 3. mmc: core: sd_uhs2.c: Move functions from uhs2.c to corespondding functions in sd_uhs2.c and remove uhs2.c from kernel source code. Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw> --- drivers/mmc/core/Makefile | 2 +- drivers/mmc/core/core.c | 2 +- drivers/mmc/core/sd.c | 2 +- drivers/mmc/core/sd.h | 1 + drivers/mmc/core/sd_uhs2.c | 1157 ++++++++++++++++++++++++++++++++++++ drivers/mmc/core/uhs2.h | 1 + drivers/mmc/host/sdhci-uhs2.c | 5 +++++ include/linux/mmc/uhs2.h | 1 + 8 files changed, 1171 insertions(+), 3 deletions(-) create mode 100644 drivers/mmc/core/sd_uhs2.c