@@ -241,6 +241,17 @@ static int __init init_9607(struct tsens_priv *priv)
for (i = 0; i < priv->num_sensors; ++i)
priv->sensor[i].slope = 3000;
+ priv->sensor[0].p1_calib_offset = 1;
+ priv->sensor[0].p2_calib_offset = 1;
+ priv->sensor[1].p1_calib_offset = -4;
+ priv->sensor[1].p2_calib_offset = -2;
+ priv->sensor[2].p1_calib_offset = 4;
+ priv->sensor[2].p2_calib_offset = 8;
+ priv->sensor[3].p1_calib_offset = -3;
+ priv->sensor[3].p2_calib_offset = -5;
+ priv->sensor[4].p1_calib_offset = -4;
+ priv->sensor[4].p2_calib_offset = -4;
+
return init_common(priv);
}
@@ -134,10 +134,12 @@ int tsens_read_calibration(struct tsens_priv *priv, int shift, u32 *p1, u32 *p2,
p1[i] = p1[i] + (base1 << shift);
break;
case TWO_PT_CALIB:
+ case TWO_PT_CALIB_NO_OFFSET:
for (i = 0; i < priv->num_sensors; i++)
p2[i] = (p2[i] + base2) << shift;
fallthrough;
case ONE_PT_CALIB2:
+ case ONE_PT_CALIB2_NO_OFFSET:
for (i = 0; i < priv->num_sensors; i++)
p1[i] = (p1[i] + base1) << shift;
break;
@@ -149,6 +151,18 @@ int tsens_read_calibration(struct tsens_priv *priv, int shift, u32 *p1, u32 *p2,
}
}
+ /* Apply calibration offset workaround except for _NO_OFFSET modes */
+ switch (mode) {
+ case TWO_PT_CALIB:
+ for (i = 0; i < priv->num_sensors; i++)
+ p2[i] += priv->sensor[i].p2_calib_offset;
+ fallthrough;
+ case ONE_PT_CALIB2:
+ for (i = 0; i < priv->num_sensors; i++)
+ p1[i] += priv->sensor[i].p1_calib_offset;
+ break;
+ }
+
return mode;
}
@@ -254,7 +268,7 @@ void compute_intercept_slope(struct tsens_priv *priv, u32 *p1,
if (!priv->sensor[i].slope)
priv->sensor[i].slope = SLOPE_DEFAULT;
- if (mode == TWO_PT_CALIB) {
+ if (mode == TWO_PT_CALIB || mode == TWO_PT_CALIB_NO_OFFSET) {
/*
* slope (m) = adc_code2 - adc_code1 (y2 - y1)/
* temp_120_degc - temp_30_degc (x2 - x1)
@@ -10,6 +10,8 @@
#define ONE_PT_CALIB 0x1
#define ONE_PT_CALIB2 0x2
#define TWO_PT_CALIB 0x3
+#define ONE_PT_CALIB2_NO_OFFSET 0x6
+#define TWO_PT_CALIB_NO_OFFSET 0x7
#define CAL_DEGC_PT1 30
#define CAL_DEGC_PT2 120
#define SLOPE_FACTOR 1000
@@ -57,6 +59,8 @@ struct tsens_sensor {
unsigned int hw_id;
int slope;
u32 status;
+ int p1_calib_offset;
+ int p2_calib_offset;
};
/**
According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs "correction factors" to adjust for additional offsets observed after the factory calibration values in the fuses [1, 2]. The fixed offsets should be applied unless there is a special calibration mode value that indicates that no offsets are needed [3]. Note that the new calibration mode values are called differently in this patch compared to the vendor kernel: - TSENS_TWO_POINT_CALIB_N_WA -> ONE_PT_CALIB2_NO_OFFSET - TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET This is because close inspection of the calibration function [3] reveals that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration because the if statements skip all "point2" related code for it. [1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d9d2db1b82bf3f72f5de0803d55e6849eb5b671e [2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d75aef53a760e8ff7bac54049d00c8b2ee1b193e [3]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/drivers/thermal/msm-tsens.c#L2987-3136 Fixes: a2149ab815fc ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607") Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> --- drivers/thermal/qcom/tsens-v0_1.c | 11 +++++++++++ drivers/thermal/qcom/tsens.c | 16 +++++++++++++++- drivers/thermal/qcom/tsens.h | 4 ++++ 3 files changed, 30 insertions(+), 1 deletion(-)