| Message ID | 20230912-msm8909-cpufreq-v1-4-767ce66b544b@kernkonzept.com |
|---|---|
| State | New |
| Headers | show |
| Series | cpufreq: Add basic cpufreq scaling for Qualcomm MSM8909 | expand |
On 12.09.2023 11:40, Stephan Gerhold wrote: > When the MSM8909 SoC is used together with the PM8909 PMIC the primary > power supply for the CPU (VDD_APC) is shared with other components to > the SoC, namely the VDD_CX power domain typically supplied by the PM8909 > S1 regulator. This means that all votes for necessary performance states > go via the RPM firmware which collects the requirements from all the > processors in the SoC. The RPM firmware then chooses the actual voltage > based on the performance states ("corners"), depending on calibration > values in the NVMEM and other factors. > > The MSM8909 SoC is also sometimes used with the PM8916 or PM660 PMIC. > In that case there is a dedicated regulator connected to VDD_APC and > Linux is responsible to do adaptive voltage scaling using CPR (similar > to the existing code for QCS404). > > This difference can be described in the device tree, by either assigning > the CPU a power domain from RPMPD or from the CPR driver. > > To describe this in a more generic way, use "apc" as power domain name > instead of "cpr". From the Linux point of view there is no CPR involved > when MSM8909 is used together with PM8909. Without checking, I have a vague recollection of CPR output also being called VDD_APCx, so it's a-ok > > Also add a simple function that reads the speedbin from a NVMEM cell > and sets it as-is for opp-supported-hw. The actual bit position can be > described in the device tree without additional driver changes. > > Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> > --- Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org> One nit below: [...] > static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { > + { .compatible = "qcom,msm8909", .data = &match_data_msm8909 }, > { .compatible = "qcom,apq8096", .data = &match_data_kryo }, msm8909 should come after apq8096 (even if adding apq and not msm was a mistake) Konrad
diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c index 17d6ab14c909..2ea5e5ee9f1c 100644 --- a/drivers/cpufreq/qcom-cpufreq-nvmem.c +++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c @@ -49,6 +49,24 @@ struct qcom_cpufreq_drv { static struct platform_device *cpufreq_dt_pdev, *cpufreq_pdev; +static int qcom_cpufreq_simple_get_version(struct device *cpu_dev, + struct nvmem_cell *speedbin_nvmem, + char **pvs_name, + struct qcom_cpufreq_drv *drv) +{ + u8 *speedbin; + + *pvs_name = NULL; + speedbin = nvmem_cell_read(speedbin_nvmem, NULL); + if (IS_ERR(speedbin)) + return PTR_ERR(speedbin); + + dev_dbg(cpu_dev, "speedbin: %d\n", *speedbin); + drv->versions = 1 << *speedbin; + kfree(speedbin); + return 0; +} + static void get_krait_bin_format_a(struct device *cpu_dev, int *speed, int *pvs, int *pvs_ver, u8 *buf) @@ -212,6 +230,13 @@ static const struct qcom_cpufreq_match_data match_data_krait = { .get_version = qcom_cpufreq_krait_name_version, }; +static const char *msm8909_genpd_names[] = { "apc", NULL }; + +static const struct qcom_cpufreq_match_data match_data_msm8909 = { + .get_version = qcom_cpufreq_simple_get_version, + .genpd_names = msm8909_genpd_names, +}; + static const char *qcs404_genpd_names[] = { "cpr", NULL }; static const struct qcom_cpufreq_match_data match_data_qcs404 = { @@ -375,6 +400,7 @@ static struct platform_driver qcom_cpufreq_driver = { }; static const struct of_device_id qcom_cpufreq_match_list[] __initconst = { + { .compatible = "qcom,msm8909", .data = &match_data_msm8909 }, { .compatible = "qcom,apq8096", .data = &match_data_kryo }, { .compatible = "qcom,msm8996", .data = &match_data_kryo }, { .compatible = "qcom,qcs404", .data = &match_data_qcs404 },
When the MSM8909 SoC is used together with the PM8909 PMIC the primary power supply for the CPU (VDD_APC) is shared with other components to the SoC, namely the VDD_CX power domain typically supplied by the PM8909 S1 regulator. This means that all votes for necessary performance states go via the RPM firmware which collects the requirements from all the processors in the SoC. The RPM firmware then chooses the actual voltage based on the performance states ("corners"), depending on calibration values in the NVMEM and other factors. The MSM8909 SoC is also sometimes used with the PM8916 or PM660 PMIC. In that case there is a dedicated regulator connected to VDD_APC and Linux is responsible to do adaptive voltage scaling using CPR (similar to the existing code for QCS404). This difference can be described in the device tree, by either assigning the CPU a power domain from RPMPD or from the CPR driver. To describe this in a more generic way, use "apc" as power domain name instead of "cpr". From the Linux point of view there is no CPR involved when MSM8909 is used together with PM8909. Also add a simple function that reads the speedbin from a NVMEM cell and sets it as-is for opp-supported-hw. The actual bit position can be described in the device tree without additional driver changes. Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> --- drivers/cpufreq/qcom-cpufreq-nvmem.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)