@@ -3531,6 +3531,26 @@ core_scsi3_emulate_pro_register_and_move(struct se_cmd *cmd, u64 res_key,
return ret;
}
+static sense_reason_t
+target_try_pr_out_pt(struct se_cmd *cmd, u8 sa, u64 res_key, u64 sa_res_key,
+ u8 type, bool aptpl, bool all_tg_pt, bool spec_i_pt)
+{
+ struct exec_cmd_ops *ops = cmd->protocol_data;
+
+ if (!cmd->se_sess || !cmd->se_lun) {
+ pr_err("SPC-3 PR: se_sess || struct se_lun is NULL!\n");
+ return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE;
+ }
+
+ if (!ops->execute_pr_out) {
+ pr_err("SPC-3 PR: Device has been configured for PR passthrough but it's not supported by the backend.\n");
+ return TCM_UNSUPPORTED_SCSI_OPCODE;
+ }
+
+ return ops->execute_pr_out(cmd, sa, res_key, sa_res_key, type,
+ aptpl, all_tg_pt, spec_i_pt);
+}
+
/*
* See spc4r17 section 6.14 Table 170
*/
@@ -3634,6 +3654,12 @@ target_scsi3_emulate_pr_out(struct se_cmd *cmd)
return TCM_PARAMETER_LIST_LENGTH_ERROR;
}
+ if (dev->transport_flags & TRANSPORT_FLAG_PASSTHROUGH_PGR) {
+ ret = target_try_pr_out_pt(cmd, sa, res_key, sa_res_key, type,
+ aptpl, all_tg_pt, spec_i_pt);
+ goto done;
+ }
+
/*
* (core_scsi3_emulate_pro_* function parameters
* are defined by spc4r17 Table 174:
@@ -3675,6 +3701,7 @@ target_scsi3_emulate_pr_out(struct se_cmd *cmd)
return TCM_INVALID_CDB_FIELD;
}
+done:
if (!ret)
target_complete_cmd(cmd, SAM_STAT_GOOD);
return ret;
@@ -4032,6 +4059,33 @@ core_scsi3_pri_read_full_status(struct se_cmd *cmd)
return 0;
}
+static sense_reason_t target_try_pr_in_pt(struct se_cmd *cmd)
+{
+ struct exec_cmd_ops *ops = cmd->protocol_data;
+ unsigned char *buf;
+ sense_reason_t ret;
+
+ if (cmd->data_length < 8) {
+ pr_err("PRIN SA SCSI Data Length: %u too small\n",
+ cmd->data_length);
+ return TCM_INVALID_CDB_FIELD;
+ }
+
+ if (!ops->execute_pr_in) {
+ pr_err("SPC-3 PR: Device has been configured for PR passthrough but it's not supported by the backend.\n");
+ return TCM_UNSUPPORTED_SCSI_OPCODE;
+ }
+
+ buf = transport_kmap_data_sg(cmd);
+ if (!buf)
+ return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE;
+
+ ret = ops->execute_pr_in(cmd, cmd->t_task_cdb[1] & 0x1f, buf);
+
+ transport_kunmap_data_sg(cmd);
+ return ret;
+}
+
sense_reason_t
target_scsi3_emulate_pr_in(struct se_cmd *cmd)
{
@@ -4053,6 +4107,11 @@ target_scsi3_emulate_pr_in(struct se_cmd *cmd)
return TCM_RESERVATION_CONFLICT;
}
+ if (cmd->se_dev->transport_flags & TRANSPORT_FLAG_PASSTHROUGH_PGR) {
+ ret = target_try_pr_in_pt(cmd);
+ goto done;
+ }
+
switch (cmd->t_task_cdb[1] & 0x1f) {
case PRI_READ_KEYS:
ret = core_scsi3_pri_read_keys(cmd);
@@ -4072,6 +4131,7 @@ target_scsi3_emulate_pr_in(struct se_cmd *cmd)
return TCM_INVALID_CDB_FIELD;
}
+done:
if (!ret)
target_complete_cmd(cmd, SAM_STAT_GOOD);
return ret;
@@ -68,6 +68,11 @@ struct exec_cmd_ops {
sense_reason_t (*execute_write_same)(struct se_cmd *cmd);
sense_reason_t (*execute_unmap)(struct se_cmd *cmd,
sector_t lba, sector_t nolb);
+ sense_reason_t (*execute_pr_out)(struct se_cmd *cmd, u8 sa, u64 key,
+ u64 sa_key, u8 type, bool aptpl,
+ bool all_tg_pt, bool spec_i_pt);
+ sense_reason_t (*execute_pr_in)(struct se_cmd *cmd, u8 sa,
+ unsigned char *param_data);
};
int transport_backend_register(const struct target_backend_ops *);
For the cases where you want to export a device to a VM via a single I_T nexus and want to passthrough the PR handling to the physical/real device you have to use pscsi or tcmu. Both are good for specific uses however for the case where you want good performance, and are not using SCSI devices directly (using DM/MD RAID or multipath devices) then we are out of luck. The following patches allow iblock to mimimally hook into the LIO PR code and then pass the PR handling to the physical device. Note that like with the tcmu an pscsi cases it's only supported when you export the device via one I_T nexus. This patch adds the initial LIO callouts. The next patch will modify iblock. Signed-off-by: Mike Christie <michael.christie@oracle.com> --- drivers/target/target_core_pr.c | 60 ++++++++++++++++++++++++++++ include/target/target_core_backend.h | 5 +++ 2 files changed, 65 insertions(+)