diff mbox series

[v10,3/6] dt-bindings: sc16is7xx: Add property to change GPIO function

Message ID 20230807214556.540627-4-hugo@hugovil.com
State New
Headers show
Series serial: sc16is7xx: fix GPIO regression and rs485 improvements | expand

Commit Message

Hugo Villeneuve Aug. 7, 2023, 9:45 p.m. UTC 
From: Hugo Villeneuve <hvilleneuve@dimonoff.com>

Some variants in this series of UART controllers have GPIO pins that
are shared between GPIO and modem control lines.

The pin mux mode (GPIO or modem control lines) can be set for each
ports (channels) supported by the variant.

This adds a property to the device tree to set the GPIO pin mux to
modem control lines on selected ports if needed.

Cc: <stable@vger.kernel.org> # 6.1.x
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
---
 .../bindings/serial/nxp,sc16is7xx.txt         | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)

Comments

Rob Herring Aug. 17, 2023, 6:02 p.m. UTC | #1 
On Mon, 07 Aug 2023 17:45:53 -0400, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> 
> Some variants in this series of UART controllers have GPIO pins that
> are shared between GPIO and modem control lines.
> 
> The pin mux mode (GPIO or modem control lines) can be set for each
> ports (channels) supported by the variant.
> 
> This adds a property to the device tree to set the GPIO pin mux to
> modem control lines on selected ports if needed.
> 
> Cc: <stable@vger.kernel.org> # 6.1.x
> Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
> ---
>  .../bindings/serial/nxp,sc16is7xx.txt         | 46 +++++++++++++++++++
>  1 file changed, 46 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
index 0fa8e3e43bf8..1a7e4bff0456 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
@@ -23,6 +23,9 @@  Optional properties:
     1 = active low.
 - irda-mode-ports: An array that lists the indices of the port that
 		   should operate in IrDA mode.
+- nxp,modem-control-line-ports: An array that lists the indices of the port that
+				should have shared GPIO lines configured as
+				modem control lines.
 
 Example:
         sc16is750: sc16is750@51 {
@@ -35,6 +38,26 @@  Example:
                 #gpio-cells = <2>;
         };
 
+	sc16is752: sc16is752@53 {
+		compatible = "nxp,sc16is752";
+		reg = <0x53>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
+		gpio-controller; /* Port 0 as GPIOs */
+		#gpio-cells = <2>;
+	};
+
+	sc16is752: sc16is752@54 {
+		compatible = "nxp,sc16is752";
+		reg = <0x54>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
+	};
+
 * spi as bus
 
 Required properties:
@@ -59,6 +82,9 @@  Optional properties:
     1 = active low.
 - irda-mode-ports: An array that lists the indices of the port that
 		   should operate in IrDA mode.
+- nxp,modem-control-line-ports: An array that lists the indices of the port that
+				should have shared GPIO lines configured as
+				modem control lines.
 
 Example:
 	sc16is750: sc16is750@0 {
@@ -70,3 +96,23 @@  Example:
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	sc16is752: sc16is752@1 {
+		compatible = "nxp,sc16is752";
+		reg = <1>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
+		gpio-controller; /* Port 0 as GPIOs */
+		#gpio-cells = <2>;
+	};
+
+	sc16is752: sc16is752@2 {
+		compatible = "nxp,sc16is752";
+		reg = <2>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
+	};