@@ -1394,11 +1394,7 @@ static int omap8250_probe(struct platform_device *pdev)
struct uart_8250_port up;
struct resource *regs;
void __iomem *membase;
- int irq, ret;
-
- irq = platform_get_irq(pdev, 0);
- if (irq < 0)
- return irq;
+ int ret;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs) {
@@ -1419,7 +1415,6 @@ static int omap8250_probe(struct platform_device *pdev)
up.port.dev = &pdev->dev;
up.port.mapbase = regs->start;
up.port.membase = membase;
- up.port.irq = irq;
/*
* It claims to be 16C750 compatible however it is a little different.
* It has EFR and has no FCR7_64byte bit. The AFE (which it claims to
@@ -1429,13 +1424,9 @@ static int omap8250_probe(struct platform_device *pdev)
* or pm callback.
*/
up.port.type = PORT_8250;
- up.port.iotype = UPIO_MEM;
- up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SOFT_FLOW |
- UPF_HARD_FLOW;
+ up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SOFT_FLOW | UPF_HARD_FLOW;
up.port.private_data = priv;
- up.port.regshift = OMAP_UART_REGSHIFT;
- up.port.fifosize = 64;
up.tx_loadsz = 64;
up.capabilities = UART_CAP_FIFO;
#ifdef CONFIG_PM
@@ -1461,14 +1452,14 @@ static int omap8250_probe(struct platform_device *pdev)
up.rs485_stop_tx = serial8250_em485_stop_tx;
up.port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_8250_CONSOLE);
- ret = of_alias_get_id(np, "serial");
- if (ret < 0) {
- dev_err(&pdev->dev, "failed to get alias\n");
+ ret = uart_read_port_properties(&up.port);
+ if (ret)
return ret;
- }
- up.port.line = ret;
- if (of_property_read_u32(np, "clock-frequency", &up.port.uartclk)) {
+ up.port.regshift = OMAP_UART_REGSHIFT;
+ up.port.fifosize = 64;
+
+ if (!up.port.uartclk) {
struct clk *clk;
clk = devm_clk_get(&pdev->dev, NULL);
@@ -1560,8 +1551,8 @@ static int omap8250_probe(struct platform_device *pdev)
}
#endif
- irq_set_status_flags(irq, IRQ_NOAUTOEN);
- ret = devm_request_irq(&pdev->dev, irq, omap8250_irq, 0,
+ irq_set_status_flags(up.port.irq, IRQ_NOAUTOEN);
+ ret = devm_request_irq(&pdev->dev, up.port.irq, omap8250_irq, 0,
dev_name(&pdev->dev), priv);
if (ret < 0)
return ret;
Since we have now a common helper to read port properties use it instead of sparse home grown solution. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> --- drivers/tty/serial/8250/8250_omap.c | 29 ++++++++++------------------- 1 file changed, 10 insertions(+), 19 deletions(-)