| Message ID | 20230704092200.85401-3-william.qiu@starfivetech.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add SPI module for StarFive JH7110 SoC | expand |
On Tue, Jul 04, 2023 at 11:39:29AM +0200, Krzysztof Kozlowski wrote: > On 04/07/2023 11:22, William Qiu wrote: > > Add spi node for JH7110 SoC. > > > > Co-developed-by: Xingyu Wu <xingyu.wu@starfivetech.com> > > Missing SoB. It's fine not to have a signoff for the codeveloper of codeveloped patches, see case (a) for the DCO.
On Tue, Jul 04, 2023 at 02:27:57PM +0200, Krzysztof Kozlowski wrote: > Also see: > "every Co-developed-by: must be immediately > followed by a Signed-off-by: of the associated co-author." > https://elixir.bootlin.com/linux/v6.4/source/Documentation/process/submitting-patches.rst#L467 Oh, that seems unhelpful especially with it not lining up with the DCO.
On Tue, Jul 04, 2023 at 03:21:30PM +0200, Krzysztof Kozlowski wrote: > On 04/07/2023 15:16, Mark Brown wrote: > > On Tue, Jul 04, 2023 at 02:27:57PM +0200, Krzysztof Kozlowski wrote: > >> Also see: > >> "every Co-developed-by: must be immediately > >> followed by a Signed-off-by: of the associated co-author." > >> https://elixir.bootlin.com/linux/v6.4/source/Documentation/process/submitting-patches.rst#L467 > > Oh, that seems unhelpful especially with it not lining up with the DCO. > I assume the intention was here that if I attribute some co-author with > Co-developed-by, then I know that author, therefore I expect author to > explicitly participate in DCO chain. Why? They're not the one sending the patch out, nor are they relying on someone else having certified anything. > Otherwise, just drop the Co-developed-by. It seems separately useful.
On Tue, Jul 04, 2023 at 03:13:17PM +0100, Mark Brown wrote: > On Tue, Jul 04, 2023 at 03:21:30PM +0200, Krzysztof Kozlowski wrote: > > On 04/07/2023 15:16, Mark Brown wrote: > > > On Tue, Jul 04, 2023 at 02:27:57PM +0200, Krzysztof Kozlowski wrote: > > > >> Also see: > > >> "every Co-developed-by: must be immediately > > >> followed by a Signed-off-by: of the associated co-author." > > > >> https://elixir.bootlin.com/linux/v6.4/source/Documentation/process/submitting-patches.rst#L467 > > > > Oh, that seems unhelpful especially with it not lining up with the DCO. > > > I assume the intention was here that if I attribute some co-author with > > Co-developed-by, then I know that author, therefore I expect author to > > explicitly participate in DCO chain. > > Why? They're not the one sending the patch out, nor are they relying on > someone else having certified anything. It's probably safe to say that StarFive owns the contributions anyway, so I doubt adding really makes a difference here. > > Otherwise, just drop the Co-developed-by. > > It seems separately useful. Yup, I'd rather have the people there if I ever have to run `git blame` on whatever commit this becomes.
On 2023/7/4 17:39, Krzysztof Kozlowski wrote: > On 04/07/2023 11:22, William Qiu wrote: >> Add spi node for JH7110 SoC. >> >> Co-developed-by: Xingyu Wu <xingyu.wu@starfivetech.com> > > Missing SoB. > It looks like that drop it is the best solution. >> Signed-off-by: William Qiu <william.qiu@starfivetech.com> >> --- >> .../jh7110-starfive-visionfive-2.dtsi | 52 ++++++++++ >> arch/riscv/boot/dts/starfive/jh7110.dtsi | 98 +++++++++++++++++++ >> 2 files changed, 150 insertions(+) >> >> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi >> index 2a6d81609284..a066d2e399c4 100644 >> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi >> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi >> @@ -126,6 +126,20 @@ &i2c6 { >> status = "okay"; >> }; >> >> +&spi0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&spi0_pins>; >> + status = "okay"; >> + >> + spi_dev0: spi@0 { >> + compatible = "st,m25p80"; >> + pl022,com-mode = <1>; >> + spi-max-frequency = <10000000>; >> + reg = <0>; > > reg is always following compatible, not somewhere deep in properties. > Will update. >> + status = "okay"; > > okay is by default > Will drop. >> + }; >> +}; > > > Best regards, > Krzysztof > Thanks for taking time to review this patch series.
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi index 2a6d81609284..a066d2e399c4 100644 --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi @@ -126,6 +126,20 @@ &i2c6 { status = "okay"; }; +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; + + spi_dev0: spi@0 { + compatible = "st,m25p80"; + pl022,com-mode = <1>; + spi-max-frequency = <10000000>; + reg = <0>; + status = "okay"; + }; +}; + &sysgpio { i2c0_pins: i2c0-0 { i2c-pins { @@ -183,6 +197,44 @@ GPOEN_SYS_I2C6_DATA, }; }; + spi0_pins: spi0-0 { + mosi-pins { + pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + }; + + miso-pins { + pinmux = <GPIOMUX(53, GPOUT_LOW, + GPOEN_DISABLE, + GPI_SYS_SPI0_RXD)>; + bias-pull-up; + input-enable; + input-schmitt-enable; + }; + + sck-pins { + pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK, + GPOEN_ENABLE, + GPI_SYS_SPI0_CLK)>; + bias-disable; + input-disable; + input-schmitt-disable; + }; + + ss-pins { + pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_FSS, + GPOEN_ENABLE, + GPI_SYS_SPI0_FSS)>; + bias-disable; + input-disable; + input-schmitt-disable; + }; + }; + uart0_pins: uart0-0 { tx-pins { pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX, diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi index 4c5fdb905da8..b32611c7cdf7 100644 --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi @@ -353,6 +353,48 @@ i2c2: i2c@10050000 { status = "disabled"; }; + spi0: spi@10060000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x10060000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI0_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI0_APB>; + interrupts = <38>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi1: spi@10070000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x10070000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI1_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI1_APB>; + interrupts = <39>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@10080000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x10080000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI2_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI2_APB>; + interrupts = <40>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart3: serial@12000000 { compatible = "snps,dw-apb-uart"; reg = <0x0 0x12000000 0x0 0x10000>; @@ -440,6 +482,62 @@ i2c6: i2c@12060000 { status = "disabled"; }; + spi3: spi@12070000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x12070000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI3_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI3_APB>; + interrupts = <52>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@12080000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x12080000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI4_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI4_APB>; + interrupts = <53>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi5: spi@12090000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x12090000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI5_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI5_APB>; + interrupts = <54>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi6: spi@120a0000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x0 0x120A0000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_SPI6_APB>; + clock-names = "apb_pclk"; + resets = <&syscrg JH7110_SYSRST_SPI6_APB>; + interrupts = <55>; + arm,primecell-periphid = <0x00041022>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + syscrg: clock-controller@13020000 { compatible = "starfive,jh7110-syscrg"; reg = <0x0 0x13020000 0x0 0x10000>;
Add spi node for JH7110 SoC. Co-developed-by: Xingyu Wu <xingyu.wu@starfivetech.com> Signed-off-by: William Qiu <william.qiu@starfivetech.com> --- .../jh7110-starfive-visionfive-2.dtsi | 52 ++++++++++ arch/riscv/boot/dts/starfive/jh7110.dtsi | 98 +++++++++++++++++++ 2 files changed, 150 insertions(+) -- 2.34.1