diff --git a/include/uapi/linux/virtio_spi.h b/include/uapi/linux/virtio_spi.h
new file mode 100644
index 000000000000..d56843fcb2ec
--- /dev/null
+++ b/include/uapi/linux/virtio_spi.h
@@ -0,0 +1,185 @@
+/* SPDX-License-Identifier: BSD-3-Clause */
+/*
+ * Copyright (C) 2023 OpenSynergy GmbH
+ */
+#ifndef _LINUX_VIRTIO_VIRTIO_SPI_H
+#define _LINUX_VIRTIO_VIRTIO_SPI_H
+
+#include <linux/types.h>
+#include <linux/virtio_types.h>
+#include <linux/virtio_ids.h>
+#include <linux/virtio_config.h>
+
+/* Sample data on trailing clock edge */
+#define VIRTIO_SPI_CPHA (1 << 0)
+/* Clock is high when IDLE */
+#define VIRTIO_SPI_CPOL (1 << 1)
+/* Chip Select is active high */
+#define VIRTIO_SPI_CS_HIGH (1 << 2)
+/* Transmit LSB first */
+#define VIRTIO_SPI_MODE_LSB_FIRST (1 << 3)
+/* Loopback mode */
+#define VIRTIO_SPI_MODE_LOOP (1 << 4)
+
+/*
+ * All config fields are read-only for the Virtio SPI driver
+ *
+ * @cs_max_number: maximum number of chipselect the host SPI controller
+ *   supports.
+ * @cs_change_supported: indicates if the host SPI controller supports to toggle
+ * chipselect after each transfer in one message:
+ *   0: unsupported, chipselect will be kept in active state throughout the
+ *      message transaction;
+ *   1: supported.
+ *   Note: Message here contains a sequence of SPI transfers.
+ * @tx_nbits_supported: indicates the supported number of bit for writing:
+ *   bit 0: DUAL (2-bit transfer), 1 for supported
+ *   bit 1: QUAD (4-bit transfer), 1 for supported
+ *   bit 2: OCTAL (8-bit transfer), 1 for supported
+ *   other bits are reserved as 0, 1-bit transfer is always supported.
+ * @rx_nbits_supported: indicates the supported number of bit for reading:
+ *   bit 0: DUAL (2-bit transfer), 1 for supported
+ *   bit 1: QUAD (4-bit transfer), 1 for supported
+ *   bit 2: OCTAL (8-bit transfer), 1 for supported
+ *   other bits are reserved as 0, 1-bit transfer is always supported.
+ * @bits_per_word_mask: mask indicating which values of bits_per_word are
+ *   supported. If not set, no limitation for bits_per_word.
+ * @mode_func_supported: indicates the following features are supported or not:
+ *   bit 0-1: CPHA feature
+ *     0b00: invalid, should support as least one CPHA setting
+ *     0b01: supports CPHA=0 only
+ *     0b10: supports CPHA=1 only
+ *     0b11: supports CPHA=0 and CPHA=1.
+ *   bit 2-3: CPOL feature
+ *     0b00: invalid, should support as least one CPOL setting
+ *     0b01: supports CPOL=0 only
+ *     0b10: supports CPOL=1 only
+ *     0b11: supports CPOL=0 and CPOL=1.
+ *   bit 4: chipselect active high feature, 0 for unsupported and 1 for
+ *     supported, chipselect active low should always be supported.
+ *   bit 5: LSB first feature, 0 for unsupported and 1 for supported,
+ *     MSB first should always be supported.
+ *   bit 6: loopback mode feature, 0 for unsupported and 1 for supported,
+ *     normal mode should always be supported.
+ * @max_freq_hz: the maximum clock rate supported in Hz unit, 0 means no
+ *   limitation for transfer speed.
+ * @max_word_delay_ns: the maximum word delay supported in ns unit,
+ *   0 means word delay feature is unsupported.
+ *   Note: Just as one message contains a sequence of transfers,
+ *         one transfer may contain a sequence of words.
+ * @max_cs_setup_ns: the maximum delay supported after chipselect is asserted,
+ *   in ns unit, 0 means delay is not supported to introduce after chipselect is
+ *   asserted.
+ * @max_cs_hold_ns: the maximum delay supported before chipselect is deasserted,
+ *   in ns unit, 0 means delay is not supported to introduce before chipselect
+ *   is deasserted.
+ * @max_cs_incative_ns: maximum delay supported after chipselect is deasserted,
+ *   in ns unit, 0 means delay is not supported to introduce after chipselect is
+ *   deasserted.
+ */
+struct virtio_spi_config {
+	/* # of /dev/spidev<bus_num>.CS with CS=0..chip_select_max_number -1 */
+	__u8 cs_max_number;
+	__u8 cs_change_supported;
+#define VIRTIO_SPI_RX_TX_SUPPORT_DUAL (1 << 0)
+#define VIRTIO_SPI_RX_TX_SUPPORT_QUAD (1 << 1)
+#define VIRTIO_SPI_RX_TX_SUPPORT_OCTAL (1 << 2)
+	__u8 tx_nbits_supported;
+	__u8 rx_nbits_supported;
+	__le32 bits_per_word_mask;
+#define VIRTIO_SPI_MF_SUPPORT_CPHA_0 (1 << 0)
+#define VIRTIO_SPI_MF_SUPPORT_CPHA_1 (1 << 1)
+#define VIRTIO_SPI_MF_SUPPORT_CPOL_0 (1 << 2)
+#define VIRTIO_SPI_MF_SUPPORT_CPOL_1 (1 << 3)
+#define VIRTIO_SPI_MF_SUPPORT_CS_HIGH (1 << 4)
+#define VIRTIO_SPI_MF_SUPPORT_LSB_FIRST (1 << 5)
+#define VIRTIO_SPI_MF_SUPPORT_LOOPBACK (1 << 6)
+	__le32 mode_func_supported;
+	__le32 max_freq_hz;
+	__le32 max_word_delay_ns;
+	__le32 max_cs_setup_ns;
+	__le32 max_cs_hold_ns;
+	__le32 max_cs_inactive_ns;
+};
+
+/*
+ * @chip_select_id: chipselect index the SPI transfer used.
+ *
+ * @bits_per_word: the number of bits in each SPI transfer word.
+ *
+ * @cs_change: whether to deselect device after finishing this transfer
+ *     before starting the next transfer, 0 means cs keep asserted and
+ *     1 means cs deasserted then asserted again.
+ *
+ * @tx_nbits: bus width for write transfer.
+ *     0,1: bus width is 1, also known as SINGLE
+ *     2  : bus width is 2, also known as DUAL
+ *     4  : bus width is 4, also known as QUAD
+ *     8  : bus width is 8, also known as OCTAL
+ *     other values are invalid.
+ *
+ * @rx_nbits: bus width for read transfer.
+ *     0,1: bus width is 1, also known as SINGLE
+ *     2  : bus width is 2, also known as DUAL
+ *     4  : bus width is 4, also known as QUAD
+ *     8  : bus width is 8, also known as OCTAL
+ *     other values are invalid.
+ *
+ * @reserved: for future use.
+ *
+ * @mode: SPI transfer mode.
+ *     bit 0: CPHA, determines the timing (i.e. phase) of the data
+ *         bits relative to the clock pulses.For CPHA=0, the
+ *         "out" side changes the data on the trailing edge of the
+ *         preceding clock cycle, while the "in" side captures the data
+ *         on (or shortly after) the leading edge of the clock cycle.
+ *         For CPHA=1, the "out" side changes the data on the leading
+ *         edge of the current clock cycle, while the "in" side
+ *         captures the data on (or shortly after) the trailing edge of
+ *         the clock cycle.
+ *     bit 1: CPOL, determines the polarity of the clock. CPOL=0 is a
+ *         clock which idles at 0, and each cycle consists of a pulse
+ *         of 1. CPOL=1 is a clock which idles at 1, and each cycle
+ *         consists of a pulse of 0.
+ *     bit 2: CS_HIGH, if 1, chip select active high, else active low.
+ *     bit 3: LSB_FIRST, determines per-word bits-on-wire, if 0, MSB
+ *         first, else LSB first.
+ *     bit 4: LOOP, loopback mode.
+ *
+ * @freq: the transfer speed in Hz.
+ *
+ * @word_delay_ns: delay to be inserted between consecutive words of a
+ *     transfer, in ns unit.
+ *
+ * @cs_setup_ns: delay to be introduced after CS is asserted, in ns
+ *     unit.
+ *
+ * @cs_delay_hold_ns: delay to be introduced before CS is deasserted
+ *     for each transfer, in ns unit.
+ *
+ * @cs_change_delay_inactive_ns: delay to be introduced after CS is
+ *     deasserted and before next asserted, in ns unit.
+ */
+struct spi_transfer_head {
+	__u8 chip_select_id;
+	__u8 bits_per_word;
+	__u8 cs_change;
+	__u8 tx_nbits;
+	__u8 rx_nbits;
+	__u8 reserved[3];
+	__le32 mode;
+	__le32 freq;
+	__le32 word_delay_ns;
+	__le32 cs_setup_ns;
+	__le32 cs_delay_hold_ns;
+	__le32 cs_change_delay_inactive_ns;
+};
+
+struct spi_transfer_result {
+#define VIRTIO_SPI_TRANS_OK 0
+#define VIRTIO_SPI_PARAM_ERR 1
+#define VIRTIO_SPI_TRANS_ERR 2
+	u8 result;
+};
+
+#endif /* #ifndef _LINUX_VIRTIO_VIRTIO_SPI_H */
