| Message ID | 20240321081439.541799-3-xu.yang_2@nxp.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v10,01/11] dt-bindings: usb: usbmisc-imx: add fsl,imx8ulp-usbmisc compatible | expand |
On Thu, Mar 21, 2024 at 04:14:31PM +0800, Xu Yang wrote: > Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board. > > Signed-off-by: Xu Yang <xu.yang_2@nxp.com> > > --- > Changes in v2: > - fix format as suggusted by Fabio > - add PTN5150 nodes > Changes in v3: > - no changes > Changes in v4: > - no changes > Changes in v5: > - no changes > Changes in v6: > - no changes > Changes in v7: > - no changes > Changes in v8: > - no changes > Changes in v9: > - no changes > Changes in v10: > - no changes > --- > arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++ > 1 file changed, 84 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > index 69dd8e31027c..bf418af31039 100644 > --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > @@ -133,6 +133,64 @@ pcal6408: gpio@21 { > gpio-controller; > #gpio-cells = <2>; > }; > + > + ptn5150_1: typec@1d { Could you sort devices in unit-address? > + compatible = "nxp,ptn5150"; > + reg = <0x1d>; > + int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_typec1>; > + status = "disabled"; > + }; > + > + ptn5150_2: typec@3d { > + compatible = "nxp,ptn5150"; > + reg = <0x3d>; > + int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>; > + pinctrl-names = "default"; Broken indent? Shawn > + pinctrl-0 = <&pinctrl_typec2>; > + status = "disabled"; > + }; > +}; > + > +&usbotg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb1>; > + dr_mode = "otg"; > + hnp-disable; > + srp-disable; > + adp-disable; > + over-current-active-low; > + status = "okay"; > +}; > + > +&usbphy1 { > + fsl,tx-d-cal = <110>; > + status = "okay"; > +}; > + > +&usbmisc1 { > + status = "okay"; > +}; > + > +&usbotg2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb2>; > + dr_mode = "otg"; > + hnp-disable; > + srp-disable; > + adp-disable; > + over-current-active-low; > + status = "okay"; > +}; > + > +&usbphy2 { > + fsl,tx-d-cal = <110>; > + status = "okay"; > +}; > + > +&usbmisc2 { > + status = "okay"; > }; > > &usdhc0 { > @@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA 0x20 > >; > }; > > + pinctrl_typec1: typec1grp { > + fsl,pins = < > + MX8ULP_PAD_PTF3__PTF3 0x3 > + >; > + }; > + > + pinctrl_typec2: typec2grp { > + fsl,pins = < > + MX8ULP_PAD_PTF5__PTF5 0x3 > + >; > + }; > + > + pinctrl_usb1: usb1grp { > + fsl,pins = < > + MX8ULP_PAD_PTF2__USB0_ID 0x10003 > + MX8ULP_PAD_PTF4__USB0_OC 0x10003 > + >; > + }; > + > + pinctrl_usb2: usb2grp { > + fsl,pins = < > + MX8ULP_PAD_PTD23__USB1_ID 0x10003 > + MX8ULP_PAD_PTF6__USB1_OC 0x10003 > + >; > + }; > + > pinctrl_usdhc0: usdhc0grp { > fsl,pins = < > MX8ULP_PAD_PTD1__SDHC0_CMD 0x3 > -- > 2.34.1 >
> > On Thu, Mar 21, 2024 at 04:14:31PM +0800, Xu Yang wrote: > > Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board. > > > > Signed-off-by: Xu Yang <xu.yang_2@nxp.com> > > > > --- > > Changes in v2: > > - fix format as suggusted by Fabio > > - add PTN5150 nodes > > Changes in v3: > > - no changes > > Changes in v4: > > - no changes > > Changes in v5: > > - no changes > > Changes in v6: > > - no changes > > Changes in v7: > > - no changes > > Changes in v8: > > - no changes > > Changes in v9: > > - no changes > > Changes in v10: > > - no changes > > --- > > arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++ > > 1 file changed, 84 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > > index 69dd8e31027c..bf418af31039 100644 > > --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > > +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts > > @@ -133,6 +133,64 @@ pcal6408: gpio@21 { > > gpio-controller; > > #gpio-cells = <2>; > > }; > > + > > + ptn5150_1: typec@1d { > > Could you sort devices in unit-address? Okay. > > > + compatible = "nxp,ptn5150"; > > + reg = <0x1d>; > > + int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_typec1>; > > + status = "disabled"; > > + }; > > + > > + ptn5150_2: typec@3d { > > + compatible = "nxp,ptn5150"; > > + reg = <0x3d>; > > + int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>; > > + pinctrl-names = "default"; > > Broken indent? Yes, will fix it. Thanks, Xu Yang > > Shawn > > > + pinctrl-0 = <&pinctrl_typec2>; > > + status = "disabled"; > > + }; > > +}; > > + > > +&usbotg1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usb1>; > > + dr_mode = "otg"; > > + hnp-disable; > > + srp-disable; > > + adp-disable; > > + over-current-active-low; > > + status = "okay"; > > +}; > > + > > +&usbphy1 { > > + fsl,tx-d-cal = <110>; > > + status = "okay"; > > +}; > > + > > +&usbmisc1 { > > + status = "okay"; > > +}; > > + > > +&usbotg2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usb2>; > > + dr_mode = "otg"; > > + hnp-disable; > > + srp-disable; > > + adp-disable; > > + over-current-active-low; > > + status = "okay"; > > +}; > > + > > +&usbphy2 { > > + fsl,tx-d-cal = <110>; > > + status = "okay"; > > +}; > > + > > +&usbmisc2 { > > + status = "okay"; > > }; > > > > &usdhc0 { > > @@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA 0x20 > > >; > > }; > > > > + pinctrl_typec1: typec1grp { > > + fsl,pins = < > > + MX8ULP_PAD_PTF3__PTF3 0x3 > > + >; > > + }; > > + > > + pinctrl_typec2: typec2grp { > > + fsl,pins = < > > + MX8ULP_PAD_PTF5__PTF5 0x3 > > + >; > > + }; > > + > > + pinctrl_usb1: usb1grp { > > + fsl,pins = < > > + MX8ULP_PAD_PTF2__USB0_ID 0x10003 > > + MX8ULP_PAD_PTF4__USB0_OC 0x10003 > > + >; > > + }; > > + > > + pinctrl_usb2: usb2grp { > > + fsl,pins = < > > + MX8ULP_PAD_PTD23__USB1_ID 0x10003 > > + MX8ULP_PAD_PTF6__USB1_OC 0x10003 > > + >; > > + }; > > + > > pinctrl_usdhc0: usdhc0grp { > > fsl,pins = < > > MX8ULP_PAD_PTD1__SDHC0_CMD 0x3 > > -- > > 2.34.1 > >
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts index 69dd8e31027c..bf418af31039 100644 --- a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts @@ -133,6 +133,64 @@ pcal6408: gpio@21 { gpio-controller; #gpio-cells = <2>; }; + + ptn5150_1: typec@1d { + compatible = "nxp,ptn5150"; + reg = <0x1d>; + int-gpios = <&gpiof 3 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec1>; + status = "disabled"; + }; + + ptn5150_2: typec@3d { + compatible = "nxp,ptn5150"; + reg = <0x3d>; + int-gpios = <&gpiof 5 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec2>; + status = "disabled"; + }; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + over-current-active-low; + status = "okay"; +}; + +&usbphy1 { + fsl,tx-d-cal = <110>; + status = "okay"; +}; + +&usbmisc1 { + status = "okay"; +}; + +&usbotg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + over-current-active-low; + status = "okay"; +}; + +&usbphy2 { + fsl,tx-d-cal = <110>; + status = "okay"; +}; + +&usbmisc2 { + status = "okay"; }; &usdhc0 { @@ -224,6 +282,32 @@ MX8ULP_PAD_PTE13__LPI2C7_SDA 0x20 >; }; + pinctrl_typec1: typec1grp { + fsl,pins = < + MX8ULP_PAD_PTF3__PTF3 0x3 + >; + }; + + pinctrl_typec2: typec2grp { + fsl,pins = < + MX8ULP_PAD_PTF5__PTF5 0x3 + >; + }; + + pinctrl_usb1: usb1grp { + fsl,pins = < + MX8ULP_PAD_PTF2__USB0_ID 0x10003 + MX8ULP_PAD_PTF4__USB0_OC 0x10003 + >; + }; + + pinctrl_usb2: usb2grp { + fsl,pins = < + MX8ULP_PAD_PTD23__USB1_ID 0x10003 + MX8ULP_PAD_PTF6__USB1_OC 0x10003 + >; + }; + pinctrl_usdhc0: usdhc0grp { fsl,pins = < MX8ULP_PAD_PTD1__SDHC0_CMD 0x3
Enable 2 USB nodes and add 2 PTN5150 nodes on i.MX8ULP evk board. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> --- Changes in v2: - fix format as suggusted by Fabio - add PTN5150 nodes Changes in v3: - no changes Changes in v4: - no changes Changes in v5: - no changes Changes in v6: - no changes Changes in v7: - no changes Changes in v8: - no changes Changes in v9: - no changes Changes in v10: - no changes --- arch/arm64/boot/dts/freescale/imx8ulp-evk.dts | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+)