diff mbox series

[v2,4/4] arm64: dts: imx8mp-iota2: Enable the USB Type-C port

Message ID 20240920080154.1595808-5-michal.vokac@ysoft.com
State New
Headers show
Series Add support for new IMX8MP based board | expand

Commit Message

Michal Vokáč Sept. 20, 2024, 8:01 a.m. UTC 
From: Petr Benes <petr.benes@ysoft.com>

Enable the USB Type-C port with the Diodes PI5USB30213A port controller.
The port supports dual role data but can operate only in source power role
and PD is not supported.

Signed-off-by: Petr Benes <petr.benes@ysoft.com>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
---
v2:
- Use typec instead of tcpc.
- Drop unneeded status.

 .../boot/dts/freescale/imx8mp-iota2-lumpy.dts | 94 +++++++++++++++++++
 1 file changed, 94 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
index d33428c58f2d..9b31a1e7a781 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-iota2-lumpy.dts
@@ -32,6 +32,17 @@  button-reset {
 		};
 	};
 
+	reg_typec: regulator-typec {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&pinctrl_usbc_vbus>;
+		pinctrl-names = "default";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "typec";
+	};
+
 	reg_usb_host: regulator-usb-host {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -218,6 +229,46 @@  &i2c2 {
 	pinctrl-names = "default";
 	status = "okay";
 
+	typec@d {
+		compatible = "diodes,pi5usb30213a";
+		reg = <0xd>;
+		interrupts-extended = <&gpio1 5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&pinctrl_typec>;
+		pinctrl-names = "default";
+
+		connector {
+			compatible = "usb-c-connector";
+			data-role = "dual";
+			label = "USB-C";
+			pd-disable;
+			power-role = "source";
+			self-powered;
+			typec-power-opmode = "default";
+			vbus-supply = <&reg_typec>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_con_hs: endpoint {
+						remote-endpoint = <&typec_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_con_ss: endpoint {
+						remote-endpoint = <&typec_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	rtc: rtc@68 {
 		compatible = "dallas,ds1341";
 		reg = <0x68>;
@@ -309,6 +360,12 @@  MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT	0x102
 		>;
 	};
 
+	pinctrl_typec: typecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05	0x1c0
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x0
@@ -322,6 +379,11 @@  MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x0
 		>;
 	};
 
+	pinctrl_usbc_vbus: usbcgrp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12	0x0
+		>;
+	};
+
 	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
@@ -389,15 +451,47 @@  &uart2 {
 	status = "okay";
 };
 
+&usb3_0 {
+	status = "okay";
+};
+
 &usb3_1 {
 	status = "okay";
 };
 
+&usb3_phy0 {
+	status = "okay";
+};
+
 &usb3_phy1 {
 	vbus-supply = <&reg_usb_host>;
 	status = "okay";
 };
 
+&usb_dwc3_0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		typec_hs: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		typec_ss: endpoint {
+			remote-endpoint = <&usb_con_ss>;
+		};
+	};
+};
+
 &usb_dwc3_1 {
 	dr_mode = "host";
 	pinctrl-names = "default";