From patchwork Wed May 27 16:46:44 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jagan Teki X-Patchwork-Id: 246749 List-Id: U-Boot discussion From: jagan at amarulasolutions.com (Jagan Teki) Date: Wed, 27 May 2020 22:16:44 +0530 Subject: [PATCH 13/24] arm: Remove configs/T1024QDS_DDR4_SECURE_BOOT_defconfig board In-Reply-To: <20200527164655.177741-1-jagan@amarulasolutions.com> References: <20200527164655.177741-1-jagan@amarulasolutions.com> Message-ID: <20200527164655.177741-14-jagan@amarulasolutions.com> This board has not been converted to CONFIG_DM_SPI by the deadline. Remove it. Signed-off-by: Jagan Teki Reviewed-by: Priyanka Jain --- arch/powerpc/cpu/mpc85xx/Kconfig | 1 - board/freescale/t102xqds/Kconfig | 14 - board/freescale/t102xqds/MAINTAINERS | 12 - board/freescale/t102xqds/Makefile | 15 - board/freescale/t102xqds/README | 328 --------- board/freescale/t102xqds/ddr.c | 195 ----- board/freescale/t102xqds/eth_t102xqds.c | 445 ------------ board/freescale/t102xqds/law.c | 31 - board/freescale/t102xqds/pci.c | 23 - board/freescale/t102xqds/spl.c | 156 ---- board/freescale/t102xqds/t1024_nand_rcw.cfg | 10 - board/freescale/t102xqds/t1024_pbi.cfg | 26 - board/freescale/t102xqds/t1024_sd_rcw.cfg | 10 - board/freescale/t102xqds/t1024_spi_rcw.cfg | 10 - board/freescale/t102xqds/t102xqds.c | 497 ------------- board/freescale/t102xqds/t102xqds.h | 14 - board/freescale/t102xqds/t102xqds_qixis.h | 63 -- board/freescale/t102xqds/tlb.c | 116 --- configs/T1024QDS_DDR4_SECURE_BOOT_defconfig | 69 -- configs/T1024QDS_DDR4_defconfig | 64 -- configs/T1024QDS_NAND_defconfig | 83 --- configs/T1024QDS_SDCARD_defconfig | 80 --- configs/T1024QDS_SECURE_BOOT_defconfig | 70 -- configs/T1024QDS_SPIFLASH_defconfig | 83 --- configs/T1024QDS_defconfig | 67 -- include/configs/T102xQDS.h | 756 -------------------- 26 files changed, 3238 deletions(-) delete mode 100644 board/freescale/t102xqds/Kconfig delete mode 100644 board/freescale/t102xqds/MAINTAINERS delete mode 100644 board/freescale/t102xqds/Makefile delete mode 100644 board/freescale/t102xqds/README delete mode 100644 board/freescale/t102xqds/ddr.c delete mode 100644 board/freescale/t102xqds/eth_t102xqds.c delete mode 100644 board/freescale/t102xqds/law.c delete mode 100644 board/freescale/t102xqds/pci.c delete mode 100644 board/freescale/t102xqds/spl.c delete mode 100644 board/freescale/t102xqds/t1024_nand_rcw.cfg delete mode 100644 board/freescale/t102xqds/t1024_pbi.cfg delete mode 100644 board/freescale/t102xqds/t1024_sd_rcw.cfg delete mode 100644 board/freescale/t102xqds/t1024_spi_rcw.cfg delete mode 100644 board/freescale/t102xqds/t102xqds.c delete mode 100644 board/freescale/t102xqds/t102xqds.h delete mode 100644 board/freescale/t102xqds/t102xqds_qixis.h delete mode 100644 board/freescale/t102xqds/tlb.c delete mode 100644 configs/T1024QDS_DDR4_SECURE_BOOT_defconfig delete mode 100644 configs/T1024QDS_DDR4_defconfig delete mode 100644 configs/T1024QDS_NAND_defconfig delete mode 100644 configs/T1024QDS_SDCARD_defconfig delete mode 100644 configs/T1024QDS_SECURE_BOOT_defconfig delete mode 100644 configs/T1024QDS_SPIFLASH_defconfig delete mode 100644 configs/T1024QDS_defconfig delete mode 100644 include/configs/T102xQDS.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index deffa831dc..96ec6360c4 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -1599,7 +1599,6 @@ source "board/freescale/mpc8572ds/Kconfig" source "board/freescale/p1023rdb/Kconfig" source "board/freescale/p1_twr/Kconfig" source "board/freescale/qemu-ppce500/Kconfig" -source "board/freescale/t102xqds/Kconfig" source "board/freescale/t1040qds/Kconfig" source "board/freescale/t104xrdb/Kconfig" source "board/freescale/t208xqds/Kconfig" diff --git a/board/freescale/t102xqds/Kconfig b/board/freescale/t102xqds/Kconfig deleted file mode 100644 index 87818a8d3a..0000000000 --- a/board/freescale/t102xqds/Kconfig +++ /dev/null @@ -1,14 +0,0 @@ -if TARGET_T1024QDS - -config SYS_BOARD - default "t102xqds" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "T102xQDS" - -source "board/freescale/common/Kconfig" - -endif diff --git a/board/freescale/t102xqds/MAINTAINERS b/board/freescale/t102xqds/MAINTAINERS deleted file mode 100644 index 7e30e5f84b..0000000000 --- a/board/freescale/t102xqds/MAINTAINERS +++ /dev/null @@ -1,12 +0,0 @@ -T102XQDS BOARD -#M: Shengzhou Liu -S: Orphan (since 2018-05) -F: board/freescale/t102xqds/ -F: include/configs/T102xQDS.h -F: configs/T1024QDS_defconfig -F: configs/T1024QDS_NAND_defconfig -F: configs/T1024QDS_SDCARD_defconfig -F: configs/T1024QDS_SPIFLASH_defconfig -F: configs/T1024QDS_DDR4_defconfig -F: configs/T1024QDS_SECURE_BOOT_defconfig -F: configs/T1024QDS_DDR4_SECURE_BOOT_defconfig diff --git a/board/freescale/t102xqds/Makefile b/board/freescale/t102xqds/Makefile deleted file mode 100644 index ae872b46c3..0000000000 --- a/board/freescale/t102xqds/Makefile +++ /dev/null @@ -1,15 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2014 Freescale Semiconductor, Inc. - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o -else -obj-y += t102xqds.o -obj-y += eth_t102xqds.o -obj-$(CONFIG_PCI) += pci.o -obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o -endif -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README deleted file mode 100644 index c00e3bafbe..0000000000 --- a/board/freescale/t102xqds/README +++ /dev/null @@ -1,328 +0,0 @@ -T1024 SoC Overview ------------------- -The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor -combines two or one 64-bit Power Architecture e5500 core respectively with high -performance datapath acceleration logic, and network peripheral bus interfaces -required for networking and telecommunications. This processor can be used in -applications such as enterprise WLAN access points, routers, switches, firewall -and other packet processing intensive small enterprise and branch office appliances, -and general-purpose embedded computing. Its high level of integration offers -significant performance benefits and greatly helps to simplify board design. - - -The T1024 SoC includes the following function and features: -- two e5500 cores, each with a private 256 KB L2 cache - - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant) - - Three levels of instructions: User, supervisor, and hypervisor - - Independent boot and reset - - Secure boot capability -- 256 KB shared L3 CoreNet platform cache (CPC) -- Interconnect CoreNet platform - - CoreNet coherency manager supporting coherent and noncoherent transactions - with prioritization and bandwidth allocation amongst CoreNet endpoints - - 150 Gbps coherent read bandwidth -- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support -- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - - Packet parsing, classification, and distribution - - Queue management for scheduling, packet sequencing, and congestion management - - Cryptography Acceleration (SEC 5.x) - - IEEE 1588 support - - Hardware buffer management for buffer allocation and deallocation - - MACSEC on DPAA-based Ethernet ports -- Ethernet interfaces - - Four 1 Gbps Ethernet controllers -- Parallel Ethernet interfaces - - Two RGMII interfaces -- High speed peripheral interfaces - - Three PCI Express 2.0 controllers/ports running at up to 5 GHz - - One SATA controller supporting 1.5 and 3.0 Gb/s operation - - One QSGMII interface - - Four SGMII interface supporting 1000 Mbps - - Three SGMII interfaces supporting up to 2500 Mbps - - 10GbE XFI or 10Base-KR interface -- Additional peripheral interfaces - - Two USB 2.0 controllers with integrated PHY - - SD/eSDHC/eMMC - - eSPI controller - - Four I2C controllers - - Four UARTs - - Four GPIO controllers - - Integrated flash controller (IFC) - - LCD interface (DIU) with 12 bit dual data rate -- Multicore programmable interrupt controller (PIC) -- Two 8-channel DMA engines -- Single source clocking implementation -- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) -- QUICC Engine block - - 32-bit RISC controller for flexible support of the communications peripherals - - Serial DMA channel for receive and transmit on all serial channels - - Two universal communication controllers, supporting TDM, HDLC, and UART - -T1023 Personality ------------------- -T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and -unavailable deep sleep. Rest of the blocks are almost same as T1024. -Differences between T1024 and T1023 -Feature T1024 T1023 -QUICC Engine: yes no -DIU: yes no -Deep Sleep: yes no -I2C controller: 4 3 -DDR: 64-bit 32-bit -IFC: 32-bit 28-bit - - -T1024QDS board Overview ------------------------ -- SERDES Connections - 4 lanes supporting the following: - - PCI Express: supports Gen 1 and Gen 2 - - SGMII 1G and SGMII 2.5G - - QSGMII - - XFI - - SATA 2.0 - - High-speed multiplexers route the SerDes traffic to appropriate slots or connectors. - - Aurora debug with dedicated connectors. -- DDR Controller - - Supports up to 1600 MTPS data-rate. - - Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card. - - Supports Single-, dual- or quad-rank DIMMs - - DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with automatic tracking of VTT. -- IFC/Local Bus - - NAND Flash: 8-bit, async, up to 2GB - - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - - NOR devices support 8 virtual banks - - Socketed to allow alternate devices - - GASIC: Simple (minimal) target within QIXIS FPGA - - PromJET rapid memory download support - - IFC Debug/Development card -- Ethernet - - Two on-board RGMII 10M/100M/1G ethernet ports. - - One QSGMII interface - - Four SGMII interface supporting 1Gbps - - Three SGMII interfaces supporting 2.5Gbps - - one 10Gbps XFI or 10Base-KR interface -- QIXIS System Logic FPGA - - Manages system power and reset sequencing. - - Manages the configurations of DUT, board, and clock for dynamic shmoo. - - Collects V-I-T data in background for code/power profiling. - - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion). - - General fault monitoring and logging. - - Powered from ATX 'standby' power supply that allows continuous operation while rest of the system is off. -- Clocks - - System and DDR clock (SYSCLK, DDRCLK). - - Switch selectable to one of 16 common settings in the interval of 64 MHz-166 MHz. - - Software programmable in 1 MHz increments from 1-200 MHz. - - SERDES clocks - - Provides clocks to SerDes blocks and slots. - - 100 MHz, 125 MHz and 156.25 MHz options. - - Spread-spectrum option for 100 MHz. -- Power Supplies - - Dedicated PMBus regulator for VDD and VDDC. - - Adjustable from 0.7V to 1.3V at 35A - - VDD can be disabled independanty from VDDC for ?deep sleep?. - - DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A. - - VTT/MVREF automatically track operating voltage. - - Dedicated 2.5V VPP supply. - - Dedicated regulators/filters for AVDD supplies. - - Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD, LVDD, POVDD, and EVDD. -- Video - - DIU supports video up to 1280x1024x32 bpp. - - Chrontel CH7201 for HDMI connection. - - TI DS90C387R for direct LCD connection. - - Raw (not encoded) video connector for testing or other encoders. -- USB - - Supports two USB 2.0 ports with integrated PHYs. - - Two type A ports with 5V at 1.5A per port. - - Second port can be converted to OTG mini-AB. -- SDHC - For T1024QDS, the SDHC port connects directly to an adapter card slot that has the following features: - - upport for optional clock feedback paths. - - Support for optional high-speed voltage translation direction controls. - - Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC. - - Support for eMMC memory devices. -- SPI - -On-board support of 3 different devices and sizes. -- Other IO - - Two Serial ports - - ProfiBus port - - Four I2C ports - - -Memory map on T1024QDS ----------------------- -Start Address End Address Description Size -0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB -0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB -0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB -0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB -0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB -0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB -0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB -0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB -0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB -0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB -0xF_0000_0000 0xF_003F_FFFF DCSR 4MB -0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB -0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB -0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB -0x0_0000_0000 0x0_ffff_ffff DDR 4GB - - -128MB NOR Flash memory Map --------------------------- -Start Address End Address Definition Max size -0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB -0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB -0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB -0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB -0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB -0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB -0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB -0xEC000000 0xEC01FFFF RCW (alt bank) 128KB -0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB -0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB -0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB -0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB -0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB -0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB -0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB -0xE8000000 0xE801FFFF RCW (current bank) 128KB - - -SerDes clock vs DIP-switch settings ------------------------------------ -SRDS_PRTCL_S1 SD1_REF_CLK1 SD1_REF_CLK2 SW4[1:4] -0x6F 100MHz 125MHz 1101 -0xD6 100MHz 100MHz 1111 -0x99 156.25MHz 100MHz 1011 - - -T1024 Clock frequency ----------------------- -BIN Core DDR Platform FMan -Bin1: 1400MHz 1600MT/s 400MHz 700MHz -Bin2: 1200MHz 1600MT/s 400MHz 600MHz -Bin3: 1000MHz 1600MT/s 400MHz 500MHz - - - -Software configurations and board settings ------------------------------------------- -1. NOR boot: - a. build NOR boot image - $ make T1024QDS_defconfig (For DDR3L, by default) - or make T1024QDS_D4_defconfig (For DDR4) - $ make - b. program u-boot.bin image to NOR flash - => tftp 1000000 u-boot.bin - => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize - set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot - - Switching between default bank0 and alternate bank4 on NOR flash - To change boot source to vbank4: - via software: run command 'qixis_reset altbank' in U-Boot. - via DIP-switch: set SW6[1:4] = '0100' - - To change boot source to vbank0: - via software: run command 'qixis_reset' in U-Boot. - via DIP-Switch: set SW6[1:4] = '0000' - -2. NAND Boot: - a. build PBL image for NAND boot - $ make T1024QDS_NAND_defconfig - $ make - b. program u-boot-with-spl-pbl.bin to NAND flash - => tftp 1000000 u-boot-with-spl-pbl.bin - => nand erase 0 $filesize - => nand write 1000000 0 $filesize - set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot - -3. SPI Boot: - a. build PBL image for SPI boot - $ make T1024QDS_SPIFLASH_defconfig - $ make - b. program u-boot-with-spl-pbl.bin to SPI flash - => tftp 1000000 u-boot-with-spl-pbl.bin - => sf probe 0 - => sf erase 0 f0000 - => sf write 1000000 0 $filesize - set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot - -4. SD Boot: - a. build PBL image for SD boot - $ make T1024QDS_SDCARD_defconfig - $ make - b. program u-boot-with-spl-pbl.bin to SD/MMC card - => tftp 1000000 u-boot-with-spl-pbl.bin - => mmc write 1000000 8 0x800 - => tftp 1000000 fsl_fman_ucode_t1024_xx.bin - => mmc write 1000000 0x820 80 - set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot - - -DIU/QE-TDM/SDXC settings -------------------- -a) For TDM Riser: set pin_mux=tdm in hwconfig -b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig -c) For HDMI(DVI): set pin_mux=hdmi in hwconfig -d) For LCD(DFP): set pin_mux=lcd in hwconfig -e) For SDXC: set adaptor=sdxc in hwconfig - -2-stage NAND/SPI/SD boot loader -------------------------------- -PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. -SPL further initializes DDR using SPD and environment variables -and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR. -Finally SPL transers control to U-Boot for futher booting. - -SPL has following features: - - Executes within 256K - - No relocation required - -Run time view of SPL framework -------------------------------------------------- -|Area | Address | -------------------------------------------------- -|SecureBoot header | 0xFFFC0000 (32KB) | -------------------------------------------------- -|GD, BD | 0xFFFC8000 (4KB) | -------------------------------------------------- -|ENV | 0xFFFC9000 (8KB) | -------------------------------------------------- -|HEAP | 0xFFFCB000 (30KB) | -------------------------------------------------- -|STACK | 0xFFFD8000 (22KB) | -------------------------------------------------- -|U-Boot SPL | 0xFFFD8000 (160KB) | -------------------------------------------------- - -NAND Flash memory Map on T1024QDS -------------------------------------------------------------- -Start End Definition Size -0x000000 0x0FFFFF U-Boot 1MB -0x100000 0x15FFFF U-Boot env 8KB -0x160000 0x17FFFF FMAN Ucode 128KB -0x180000 0x19FFFF QE Firmware 128KB - - -SD Card memory Map on T1024QDS ----------------------------------------------------- -Block #blocks Definition Size -0x008 2048 U-Boot img 1MB -0x800 0016 U-Boot env 8KB -0x820 0256 FMAN Ucode 128KB -0x920 0256 QE Firmware 128KB - - -SPI Flash memory Map on T1024QDS ----------------------------------------------------- -Start End Definition Size -0x000000 0x0FFFFF U-Boot img 1MB -0x100000 0x101FFF U-Boot env 8KB -0x110000 0x12FFFF FMAN Ucode 128KB -0x130000 0x14FFFF QE Firmware 128KB - - -For more details, please refer to T1024QDS Reference Manual and access -website www.freescale.com and Freescale QorIQ SDK Infocenter document. diff --git a/board/freescale/t102xqds/ddr.c b/board/freescale/t102xqds/ddr.c deleted file mode 100644 index c27cecd5aa..0000000000 --- a/board/freescale/t102xqds/ddr.c +++ /dev/null @@ -1,195 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -struct board_specific_parameters { - u32 n_ranks; - u32 datarate_mhz_high; - u32 rank_gb; - u32 clk_adjust; - u32 wrlvl_start; - u32 wrlvl_ctl_2; - u32 wrlvl_ctl_3; -}; - -/* - * datarate_mhz_high values need to be in ascending order - */ -static const struct board_specific_parameters udimm0[] = { - /* - * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | - */ -#if defined(CONFIG_SYS_FSL_DDR4) - {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, - {2, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,}, - {1, 1666, 0, 8, 6, 0x0708090B, 0x0C0D0E09,}, - {1, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,}, - {1, 2200, 0, 8, 7, 0x08090A0D, 0x0F0F100C,}, -#elif defined(CONFIG_SYS_FSL_DDR3) - {2, 833, 0, 8, 6, 0x06060607, 0x08080807,}, - {2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,}, - {2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, - {1, 833, 0, 8, 6, 0x06060607, 0x08080807,}, - {1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,}, - {1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,}, -#else -#error DDR type not defined -#endif - {} -}; - -static const struct board_specific_parameters *udimms[] = { - udimm0, -}; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - struct cpu_type *cpu = gd->arch.cpu; - - if (ctrl_num > 2) { - printf("Not supported controller number %d\n", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - pbsp = udimms[0]; - - /* Get clk_adjust according to the board ddr freqency and n_banks - * specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks && - (pdimm->rank_density >> 30) >= pbsp->rank_gb) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found\n"); - printf("for data rate %lu MT/s\n", ddr_freq); - printf("Trying to use the highest speed (%u) parameters\n", - pbsp_highest->datarate_mhz_high); - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - } else { - panic("DIMM is not supported by this board"); - } -found: - debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n", - pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb); - debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ", - pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2); - debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3); - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 1; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * rtt and rtt_wr override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 75 Ohm */ -#ifdef CONFIG_SYS_FSL_DDR4 - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) | - DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */ -#else - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); - - /* optimize cpo for erratum A-009942 */ - popts->cpo_sample = 0x5f; -#endif - - /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit, - * set DDR bus width to 32bit for T1023 - */ - if (cpu->soc_ver == SVR_T1023) - popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; - -#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32 - /* for DDR bus 32bit test on T1024 */ - popts->data_bus_width = DDR_DATA_BUS_WIDTH_32; -#endif -} - -#if defined(CONFIG_DEEP_SLEEP) -void board_mem_sleep_setup(void) -{ - void __iomem *qixis_base = (void *)QIXIS_BASE; - - /* does not provide HW signals for power management */ - clrbits_8(qixis_base + 0x21, 0x2); - /* Disable MCKE isolation */ - gpio_set_value(2, 0); - udelay(1); -} -#endif - -int dram_init(void) -{ - phys_size_t dram_size; - -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) - puts("Initializing....using SPD\n"); - dram_size = fsl_ddr_sdram(); -#else - /* DDR has been initialised by first stage boot loader */ - dram_size = fsl_ddr_sdram_size(); -#endif - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - -#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD) - fsl_dp_resume(); -#endif - - gd->ram_size = dram_size; - - return 0; -} diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c deleted file mode 100644 index 49ea21a83a..0000000000 --- a/board/freescale/t102xqds/eth_t102xqds.c +++ /dev/null @@ -1,445 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * - * Shengzhou Liu - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "../common/fman.h" -#include "t102xqds_qixis.h" - -#define EMI_NONE 0xFFFFFFFF -#define EMI1_RGMII1 0 -#define EMI1_RGMII2 1 -#define EMI1_SLOT1 2 -#define EMI1_SLOT2 3 -#define EMI1_SLOT3 4 -#define EMI1_SLOT4 5 -#define EMI1_SLOT5 6 -#define EMI2 7 - -static int mdio_mux[NUM_FM_PORTS]; - -static const char * const mdio_names[] = { - "T1024QDS_MDIO_RGMII1", - "T1024QDS_MDIO_RGMII2", - "T1024QDS_MDIO_SLOT1", - "T1024QDS_MDIO_SLOT2", - "T1024QDS_MDIO_SLOT3", - "T1024QDS_MDIO_SLOT4", - "T1024QDS_MDIO_SLOT5", - "T1024QDS_MDIO_10GC", - "NULL", -}; - -/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */ -static u8 lane_to_slot[] = {2, 3, 4, 5}; - -static const char *t1024qds_mdio_name_for_muxval(u8 muxval) -{ - return mdio_names[muxval]; -} - -struct mii_dev *mii_dev_for_muxval(u8 muxval) -{ - struct mii_dev *bus; - const char *name; - - if (muxval > EMI2) - return NULL; - - name = t1024qds_mdio_name_for_muxval(muxval); - - if (!name) { - printf("No bus for muxval %x\n", muxval); - return NULL; - } - - bus = miiphy_get_dev_by_name(name); - - if (!bus) { - printf("No bus by name %s\n", name); - return NULL; - } - - return bus; -} - -struct t1024qds_mdio { - u8 muxval; - struct mii_dev *realbus; -}; - -static void t1024qds_mux_mdio(u8 muxval) -{ - u8 brdcfg4; - - if (muxval < 7) { - brdcfg4 = QIXIS_READ(brdcfg[4]); - brdcfg4 &= ~BRDCFG4_EMISEL_MASK; - brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); - QIXIS_WRITE(brdcfg[4], brdcfg4); - } -} - -static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad, - int regnum) -{ - struct t1024qds_mdio *priv = bus->priv; - - t1024qds_mux_mdio(priv->muxval); - - return priv->realbus->read(priv->realbus, addr, devad, regnum); -} - -static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad, - int regnum, u16 value) -{ - struct t1024qds_mdio *priv = bus->priv; - - t1024qds_mux_mdio(priv->muxval); - - return priv->realbus->write(priv->realbus, addr, devad, regnum, value); -} - -static int t1024qds_mdio_reset(struct mii_dev *bus) -{ - struct t1024qds_mdio *priv = bus->priv; - - return priv->realbus->reset(priv->realbus); -} - -static int t1024qds_mdio_init(char *realbusname, u8 muxval) -{ - struct t1024qds_mdio *pmdio; - struct mii_dev *bus = mdio_alloc(); - - if (!bus) { - printf("Failed to allocate t1024qds MDIO bus\n"); - return -1; - } - - pmdio = malloc(sizeof(*pmdio)); - if (!pmdio) { - printf("Failed to allocate t1024qds private data\n"); - free(bus); - return -1; - } - - bus->read = t1024qds_mdio_read; - bus->write = t1024qds_mdio_write; - bus->reset = t1024qds_mdio_reset; - strcpy(bus->name, t1024qds_mdio_name_for_muxval(muxval)); - - pmdio->realbus = miiphy_get_dev_by_name(realbusname); - - if (!pmdio->realbus) { - printf("No bus with name %s\n", realbusname); - free(bus); - free(pmdio); - return -1; - } - - pmdio->muxval = muxval; - bus->priv = pmdio; - return mdio_register(bus); -} - -void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, - enum fm_port port, int offset) -{ - struct fixed_link f_link; - - if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) { - if (port == FM1_DTSEC3) { - fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2"); - fdt_setprop_string(fdt, offset, "phy-connection-type", - "rgmii"); - fdt_status_okay_by_alias(fdt, "emi1_rgmii1"); - } - } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) { - if (port == FM1_DTSEC1) { - fdt_set_phy_handle(fdt, compat, addr, - "sgmii_vsc8234_phy_s5"); - } else if (port == FM1_DTSEC2) { - fdt_set_phy_handle(fdt, compat, addr, - "sgmii_vsc8234_phy_s4"); - } - } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) { - if (port == FM1_DTSEC3) { - fdt_set_phy_handle(fdt, compat, addr, - "sgmii_aqr105_phy_s3"); - } - } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) { - switch (port) { - case FM1_DTSEC1: - fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1"); - break; - case FM1_DTSEC2: - fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2"); - break; - case FM1_DTSEC3: - fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3"); - break; - case FM1_DTSEC4: - fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4"); - break; - default: - break; - } - fdt_delprop(fdt, offset, "phy-connection-type"); - fdt_setprop_string(fdt, offset, "phy-connection-type", - "qsgmii"); - fdt_status_okay_by_alias(fdt, "emi1_slot2"); - } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) { - /* XFI interface */ - f_link.phy_id = port; - f_link.duplex = 1; - f_link.link_speed = 10000; - f_link.pause = 0; - f_link.asym_pause = 0; - /* no PHY for XFI */ - fdt_delprop(fdt, offset, "phy-handle"); - fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link)); - fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii"); - } -} - -void fdt_fixup_board_enet(void *fdt) -{ -} - -/* - * This function reads RCW to check if Serdes1{A:D} is configured - * to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly - */ -static void initialize_lane_to_slot(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - - srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - - switch (srds_s1) { - case 0x46: - case 0x47: - lane_to_slot[1] = 2; - break; - default: - break; - } -} - -int board_eth_init(bd_t *bis) -{ -#if defined(CONFIG_FMAN_ENET) - int i, idx, lane, slot, interface; - struct memac_mdio_info dtsec_mdio_info; - struct memac_mdio_info tgec_mdio_info; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_s1; - - srds_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - - initialize_lane_to_slot(); - - /* Initialize the mdio_mux array so we can recognize empty elements */ - for (i = 0; i < NUM_FM_PORTS; i++) - mdio_mux[i] = EMI_NONE; - - dtsec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR; - - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fm_memac_mdio_init(bis, &dtsec_mdio_info); - - tgec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR; - tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; - - /* Register the 10G MDIO bus */ - fm_memac_mdio_init(bis, &tgec_mdio_info); - - /* Register the muxing front-ends to the MDIO buses */ - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); - t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5); - t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2); - - /* Set the two on-board RGMII PHY address */ - fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR); - fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR); - - switch (srds_s1) { - case 0xd5: - case 0xd6: - /* QSGMII in Slot2 */ - fm_info_set_phy_address(FM1_DTSEC1, 0x8); - fm_info_set_phy_address(FM1_DTSEC2, 0x9); - fm_info_set_phy_address(FM1_DTSEC3, 0xa); - fm_info_set_phy_address(FM1_DTSEC4, 0xb); - break; - case 0x95: - case 0x99: - /* - * XFI does not need a PHY to work, but to avoid U-Boot use - * default PHY address which is zero to a MAC when it found - * a MAC has no PHY address, we give a PHY address to XFI - * MAC, and should not use a real XAUI PHY address, since - * MDIO can access it successfully, and then MDIO thinks the - * XAUI card is used for the XFI MAC, which will cause error. - */ - fm_info_set_phy_address(FM1_10GEC1, 4); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x6f: - /* SGMII in Slot3, Slot4, Slot5 */ - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x7f: - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3); - break; - case 0x47: - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x77: - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3); - break; - case 0x5a: - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x6a: - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x5b: - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); - break; - case 0x6b: - fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR); - break; - default: - break; - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - idx = i - FM1_DTSEC1; - interface = fm_info_get_enet_if(i); - switch (interface) { - case PHY_INTERFACE_MODE_SGMII: - case PHY_INTERFACE_MODE_SGMII_2500: - case PHY_INTERFACE_MODE_QSGMII: - if (interface == PHY_INTERFACE_MODE_SGMII) { - lane = serdes_get_first_lane(FSL_SRDS_1, - SGMII_FM1_DTSEC1 + idx); - } else if (interface == PHY_INTERFACE_MODE_SGMII_2500) { - lane = serdes_get_first_lane(FSL_SRDS_1, - SGMII_2500_FM1_DTSEC1 + idx); - } else { - lane = serdes_get_first_lane(FSL_SRDS_1, - QSGMII_FM1_A); - } - - if (lane < 0) - break; - - slot = lane_to_slot[lane]; - debug("FM1 at DTSEC%u expects SGMII in slot %u\n", - idx + 1, slot); - if (QIXIS_READ(present2) & (1 << (slot - 1))) - fm_disable_port(i); - - switch (slot) { - case 2: - mdio_mux[i] = EMI1_SLOT2; - fm_info_set_mdio(i, mii_dev_for_muxval( - mdio_mux[i])); - break; - case 3: - mdio_mux[i] = EMI1_SLOT3; - fm_info_set_mdio(i, mii_dev_for_muxval( - mdio_mux[i])); - break; - case 4: - mdio_mux[i] = EMI1_SLOT4; - fm_info_set_mdio(i, mii_dev_for_muxval( - mdio_mux[i])); - break; - case 5: - mdio_mux[i] = EMI1_SLOT5; - fm_info_set_mdio(i, mii_dev_for_muxval( - mdio_mux[i])); - break; - } - break; - case PHY_INTERFACE_MODE_RGMII: - if (i == FM1_DTSEC3) - mdio_mux[i] = EMI1_RGMII2; - else if (i == FM1_DTSEC4) - mdio_mux[i] = EMI1_RGMII1; - fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } - - for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { - idx = i - FM1_10GEC1; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - lane = serdes_get_first_lane(FSL_SRDS_1, - XFI_FM1_MAC1 + idx); - if (lane < 0) - break; - mdio_mux[i] = EMI2; - fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } - - cpu_eth_init(bis); -#endif /* CONFIG_FMAN_ENET */ - - return pci_eth_init(bis); -} diff --git a/board/freescale/t102xqds/law.c b/board/freescale/t102xqds/law.c deleted file mode 100644 index d3c1dba934..0000000000 --- a/board/freescale/t102xqds/law.c +++ /dev/null @@ -1,31 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include -#include - -struct law_entry law_table[] = { -#ifdef CONFIG_MTD_NOR_FLASH - SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), -#endif -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), -#endif -#ifdef QIXIS_BASE_PHYS - SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), -#endif -#ifdef CONFIG_SYS_NAND_BASE_PHYS - SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), -#endif -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t102xqds/pci.c b/board/freescale/t102xqds/pci.c deleted file mode 100644 index 1b1cc0483c..0000000000 --- a/board/freescale/t102xqds/pci.c +++ /dev/null @@ -1,23 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -void pci_init_board(void) -{ - fsl_pcie_init_board(0); -} - -void pci_of_setup(void *blob, bd_t *bd) -{ - FT_FSL_PCI_SETUP; -} diff --git a/board/freescale/t102xqds/spl.c b/board/freescale/t102xqds/spl.c deleted file mode 100644 index 9f4a43ed56..0000000000 --- a/board/freescale/t102xqds/spl.c +++ /dev/null @@ -1,156 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "t102xqds_qixis.h" -#include "../common/spl.h" - -DECLARE_GLOBAL_DATA_PTR; - -phys_size_t get_effective_memsize(void) -{ - return CONFIG_SYS_L3_SIZE; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); - - switch (sysclk_conf & 0x0F) { - case QIXIS_SYSCLK_83: - return 83333333; - case QIXIS_SYSCLK_100: - return 100000000; - case QIXIS_SYSCLK_125: - return 125000000; - case QIXIS_SYSCLK_133: - return 133333333; - case QIXIS_SYSCLK_150: - return 150000000; - case QIXIS_SYSCLK_160: - return 160000000; - case QIXIS_SYSCLK_166: - return 166666666; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); - - switch ((ddrclk_conf & 0x30) >> 4) { - case QIXIS_DDRCLK_100: - return 100000000; - case QIXIS_DDRCLK_125: - return 125000000; - case QIXIS_DDRCLK_133: - return 133333333; - } - return 66666666; -} - -void board_init_f(ulong bootflag) -{ - u32 plat_ratio, sys_clk, ccb_clk; - ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; - -#if defined(CONFIG_ARCH_T1040) && defined(CONFIG_SPL_NAND_BOOT) - /* - * There is T1040 SoC issue where NOR, FPGA are inaccessible during - * NAND boot because IFC signals > IFC_AD7 are not enabled. - * This workaround changes RCW source to make all signals enabled. - */ - u32 porsr1, pinctl; -#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000 - - porsr1 = in_be32(&gur->porsr1); - pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000); - out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl); -#endif - - /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ - memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); - - /* Update GD pointer */ - gd = (gd_t *)(CONFIG_SPL_GD_ADDR); - - console_init_f(); - - /* initialize selected port with appropriate baud rate */ - sys_clk = get_board_sys_clk(); - plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; - ccb_clk = sys_clk * plat_ratio / 2; - - NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - ccb_clk / 16 / CONFIG_BAUDRATE); - -#if defined(CONFIG_SPL_MMC_BOOT) - puts("\nSD boot...\n"); -#elif defined(CONFIG_SPL_SPI_BOOT) - puts("\nSPI boot...\n"); -#elif defined(CONFIG_SPL_NAND_BOOT) - puts("\nNAND boot...\n"); -#endif - - relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - bd_t *bd; - - bd = (bd_t *)(gd + sizeof(gd_t)); - memset(bd, 0, sizeof(bd_t)); - gd->bd = bd; - bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; - bd->bi_memsize = CONFIG_SYS_L3_SIZE; - - arch_cpu_init(); - get_clocks(); - mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, - CONFIG_SPL_RELOC_MALLOC_SIZE); - gd->flags |= GD_FLG_FULL_MALLOC_INIT; - -#ifdef CONFIG_SPL_NAND_BOOT - nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif -#ifdef CONFIG_SPL_MMC_BOOT - mmc_initialize(bd); - mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif -#ifdef CONFIG_SPL_SPI_BOOT - fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif - - gd->env_addr = (ulong)(SPL_ENV_ADDR); - gd->env_valid = ENV_VALID; - - i2c_init_all(); - - dram_init(); - -#ifdef CONFIG_SPL_MMC_BOOT - mmc_boot(); -#elif defined(CONFIG_SPL_SPI_BOOT) - fsl_spi_boot(); -#elif defined(CONFIG_SPL_NAND_BOOT) - nand_boot(); -#endif -} diff --git a/board/freescale/t102xqds/t1024_nand_rcw.cfg b/board/freescale/t102xqds/t1024_nand_rcw.cfg deleted file mode 100644 index 4b8f7194dc..0000000000 --- a/board/freescale/t102xqds/t1024_nand_rcw.cfg +++ /dev/null @@ -1,10 +0,0 @@ -# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz -# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz - -# PBL preamble and RCW header for T1024QDS -aa55aa55 010e0100 -# Serdes protocol 0x6F -0810000e 00000000 00000000 00000000 -37800001 00000012 e8104000 21000000 -00000000 00000000 00000000 00030810 -00000000 036c5a00 00000000 00000006 diff --git a/board/freescale/t102xqds/t1024_pbi.cfg b/board/freescale/t102xqds/t1024_pbi.cfg deleted file mode 100644 index 98efca25a2..0000000000 --- a/board/freescale/t102xqds/t1024_pbi.cfg +++ /dev/null @@ -1,26 +0,0 @@ -#PBI commands -#Initialize CPC1 -09010000 00200400 -09138000 00000000 -091380c0 00000100 -#Configure CPC1 as 256KB SRAM -09010100 00000000 -09010104 fffc0007 -09010f00 081e000d -09010000 80000000 -#Configure LAW for CPC1 -09000cd0 00000000 -09000cd4 fffc0000 -09000cd8 81000011 -#Configure alternate space -09000010 00000000 -09000014 ff000000 -09000018 81000000 -#Configure SPI controller -09110000 80000403 -09110020 2d170008 -09110024 00100008 -09110028 00100008 -0911002c 00100008 -#Flush PBL data -091380c0 000FFFFF diff --git a/board/freescale/t102xqds/t1024_sd_rcw.cfg b/board/freescale/t102xqds/t1024_sd_rcw.cfg deleted file mode 100644 index 3eca275db3..0000000000 --- a/board/freescale/t102xqds/t1024_sd_rcw.cfg +++ /dev/null @@ -1,10 +0,0 @@ -# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz -# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz - -# PBL preamble and RCW header for T1024QDS -aa55aa55 010e0100 -# Serdes protocol 0x6F -0810000e 00000000 00000000 00000000 -37800001 00000012 68104000 21000000 -00000000 00000000 00000000 00030810 -00000000 036c5a00 00000000 00000006 diff --git a/board/freescale/t102xqds/t1024_spi_rcw.cfg b/board/freescale/t102xqds/t1024_spi_rcw.cfg deleted file mode 100644 index 1601e35fc8..0000000000 --- a/board/freescale/t102xqds/t1024_spi_rcw.cfg +++ /dev/null @@ -1,10 +0,0 @@ -# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz -# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz - -# PBL preamble and RCW header for T1024QDS -aa55aa55 010e0100 -# Serdes protocol 0x6F -0810000e 00000000 00000000 00000000 -37800001 00000012 58104000 21000000 -00000000 00000000 00000000 00030810 -00000000 036c5a00 00000000 00000006 diff --git a/board/freescale/t102xqds/t102xqds.c b/board/freescale/t102xqds/t102xqds.c deleted file mode 100644 index 84db2fa9bc..0000000000 --- a/board/freescale/t102xqds/t102xqds.c +++ /dev/null @@ -1,497 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "t102xqds.h" -#include "t102xqds_qixis.h" -#include "../common/sleep.h" - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - char buf[64]; - struct cpu_type *cpu = gd->arch.cpu; - static const char *const freq[] = {"100", "125", "156.25", "100.0"}; - int clock; - u8 sw = QIXIS_READ(arch); - - printf("Board: %sQDS, ", cpu->name); - printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4); - printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1); - -#ifdef CONFIG_SDCARD - puts("SD/MMC\n"); -#elif CONFIG_SPIFLASH - puts("SPI\n"); -#else - sw = QIXIS_READ(brdcfg[0]); - sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; - - if (sw < 0x8) - printf("vBank: %d\n", sw); - else if (sw == 0x8) - puts("PromJet\n"); - else if (sw == 0x9) - puts("NAND\n"); - else if (sw == 0x15) - printf("IFC Card\n"); - else - printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); -#endif - - printf("FPGA: v%d (%s), build %d", - (int)QIXIS_READ(scver), qixis_read_tag(buf), - (int)qixis_read_minor()); - /* the timestamp string contains "\n" at the end */ - printf(" on %s", qixis_read_time(buf)); - - puts("SERDES Reference: "); - sw = QIXIS_READ(brdcfg[2]); - clock = (sw >> 6) & 3; - printf("Clock1=%sMHz ", freq[clock]); - clock = (sw >> 4) & 3; - printf("Clock2=%sMHz\n", freq[clock]); - - return 0; -} - -int select_i2c_ch_pca9547(u8 ch, int bus_num) -{ - int ret; -#ifdef CONFIG_DM_I2C - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_write(dev, 0, &ch, 1); -#else - ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); -#endif - if (ret) { - puts("PCA: failed to select proper channel\n"); - return ret; - } - - return 0; -} - -static int board_mux_lane_to_slot(void) -{ - ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_prtcl_s1; - u8 brdcfg9; - - srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - - - brdcfg9 = QIXIS_READ(brdcfg[9]); - QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE); - - switch (srds_prtcl_s1) { - case 0: - /* SerDes1 is not enabled */ - break; - case 0xd5: - case 0x5b: - case 0x6b: - case 0x77: - case 0x6f: - case 0x7f: - QIXIS_WRITE(brdcfg[12], 0x8c); - break; - case 0x40: - QIXIS_WRITE(brdcfg[12], 0xfc); - break; - case 0xd6: - case 0x5a: - case 0x6a: - case 0x56: - QIXIS_WRITE(brdcfg[12], 0x88); - break; - case 0x47: - QIXIS_WRITE(brdcfg[12], 0xcc); - break; - case 0x46: - QIXIS_WRITE(brdcfg[12], 0xc8); - break; - case 0x95: - case 0x99: - brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE; - QIXIS_WRITE(brdcfg[9], brdcfg9); - QIXIS_WRITE(brdcfg[12], 0x8c); - break; - case 0x116: - QIXIS_WRITE(brdcfg[12], 0x00); - break; - case 0x115: - case 0x119: - case 0x129: - case 0x12b: - /* Aurora, PCIe, SGMII, SATA */ - QIXIS_WRITE(brdcfg[12], 0x04); - break; - default: - printf("WARNING: unsupported for SerDes Protocol %d\n", - srds_prtcl_s1); - return -1; - } - - return 0; -} - -#ifdef CONFIG_ARCH_T1024 -static void board_mux_setup(void) -{ - u8 brdcfg15; - - brdcfg15 = QIXIS_READ(brdcfg[15]); - brdcfg15 &= ~BRDCFG15_DIUSEL_MASK; - - if (hwconfig_arg_cmp("pin_mux", "tdm")) { - /* Route QE_TDM multiplexed signals to TDM Riser slot */ - QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM); - QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2); - QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & - ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM); - } else if (hwconfig_arg_cmp("pin_mux", "ucc")) { - /* to UCC (ProfiBus) interface */ - QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC); - } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) { - /* to DVI (HDMI) encoder */ - QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI); - } else if (hwconfig_arg_cmp("pin_mux", "lcd")) { - /* to DFP (LCD) encoder */ - QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM | - BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD); - } - - if (hwconfig_arg_cmp("adaptor", "sdxc")) - /* Route SPI_CS multiplexed signals to SD slot */ - QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & - ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC); -} -#endif - -void board_retimer_ds125df111_init(void) -{ - u8 reg; - -#ifdef CONFIG_DM_I2C - struct udevice *dev; - int ret, bus_num = 0; - - ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, - 1, &dev); - if (ret) - goto failed; - - /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */ - reg = I2C_MUX_CH7; - dm_i2c_write(dev, 0, ®, 1); - - ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_SEC, - 1, &dev); - if (ret) - goto failed; - - reg = I2C_MUX_CH5; - dm_i2c_write(dev, 0, ®, 1); - - /* Access to Control/Shared register */ - ret = i2c_get_chip_for_busnum(bus_num, I2C_RETIMER_ADDR, - 1, &dev); - if (ret) - goto failed; - reg = 0x0; - dm_i2c_write(dev, 0xff, ®, 1); - - /* Read device revision and ID */ - dm_i2c_read(dev, 1, ®, 1); - debug("Retimer version id = 0x%x\n", reg); - - /* Enable Broadcast */ - reg = 0x0c; - dm_i2c_write(dev, 0xff, ®, 1); - - /* Reset Channel Registers */ - dm_i2c_read(dev, 0, ®, 1); - reg |= 0x4; - dm_i2c_write(dev, 0, ®, 1); - - /* Enable override divider select and Enable Override Output Mux */ - dm_i2c_read(dev, 9, ®, 1); - reg |= 0x24; - dm_i2c_write(dev, 9, ®, 1); - - /* Select VCO Divider to full rate (000) */ - dm_i2c_read(dev, 0x18, ®, 1); - reg &= 0x8f; - dm_i2c_write(dev, 0x18, ®, 1); - - /* Select active PFD MUX input as re-timed data (001) */ - dm_i2c_read(dev, 0x1e, ®, 1); - reg &= 0x3f; - reg |= 0x20; - dm_i2c_write(dev, 0x1e, ®, 1); - - /* Set data rate as 10.3125 Gbps */ - reg = 0x0; - dm_i2c_write(dev, 0x60, ®, 1); - reg = 0xb2; - dm_i2c_write(dev, 0x61, ®, 1); - reg = 0x90; - dm_i2c_write(dev, 0x62, ®, 1); - reg = 0xb3; - dm_i2c_write(dev, 0x63, ®, 1); - reg = 0xcd; - dm_i2c_write(dev, 0x64, ®, 1); - return; - -failed: - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return; -#else - /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */ - reg = I2C_MUX_CH7; - i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, ®, 1); - reg = I2C_MUX_CH5; - i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, ®, 1); - - /* Access to Control/Shared register */ - reg = 0x0; - i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1); - - /* Read device revision and ID */ - i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1); - debug("Retimer version id = 0x%x\n", reg); - - /* Enable Broadcast */ - reg = 0x0c; - i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1); - - /* Reset Channel Registers */ - i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1); - reg |= 0x4; - i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1); - - /* Enable override divider select and Enable Override Output Mux */ - i2c_read(I2C_RETIMER_ADDR, 9, 1, ®, 1); - reg |= 0x24; - i2c_write(I2C_RETIMER_ADDR, 9, 1, ®, 1); - - /* Select VCO Divider to full rate (000) */ - i2c_read(I2C_RETIMER_ADDR, 0x18, 1, ®, 1); - reg &= 0x8f; - i2c_write(I2C_RETIMER_ADDR, 0x18, 1, ®, 1); - - /* Select active PFD MUX input as re-timed data (001) */ - i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1); - reg &= 0x3f; - reg |= 0x20; - i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1); - - /* Set data rate as 10.3125 Gbps */ - reg = 0x0; - i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1); - reg = 0xb2; - i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1); - reg = 0x90; - i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1); - reg = 0xb3; - i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1); - reg = 0xcd; - i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1); -#endif -} - -int board_early_init_f(void) -{ -#if defined(CONFIG_DEEP_SLEEP) - if (is_warm_boot()) - fsl_dp_disable_console(); -#endif - - return 0; -} - -int board_early_init_r(void) -{ -#ifdef CONFIG_SYS_FLASH_BASE - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - int flash_esel = find_tlb_idx((void *)flashbase, 1); - - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - if (flash_esel == -1) { - /* very unlikely unless something is messed up */ - puts("Error: Could not find TLB for FLASH BASE\n"); - flash_esel = 2; /* give our best effort to continue */ - } else { - /* invalidate existing TLB entry for flash + promjet */ - disable_tlb(flash_esel); - } - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); -#endif - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); - board_mux_lane_to_slot(); - board_retimer_ds125df111_init(); - - /* Increase IO drive strength to address FCS error on RGMII */ - out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800); - - return 0; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); - - switch (sysclk_conf & 0x0F) { - case QIXIS_SYSCLK_64: - return 64000000; - case QIXIS_SYSCLK_83: - return 83333333; - case QIXIS_SYSCLK_100: - return 100000000; - case QIXIS_SYSCLK_125: - return 125000000; - case QIXIS_SYSCLK_133: - return 133333333; - case QIXIS_SYSCLK_150: - return 150000000; - case QIXIS_SYSCLK_160: - return 160000000; - case QIXIS_SYSCLK_166: - return 166666666; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); - - switch ((ddrclk_conf & 0x30) >> 4) { - case QIXIS_DDRCLK_100: - return 100000000; - case QIXIS_DDRCLK_125: - return 125000000; - case QIXIS_DDRCLK_133: - return 133333333; - } - return 66666666; -} - -#define NUM_SRDS_PLL 2 -int misc_init_r(void) -{ -#ifdef CONFIG_ARCH_T1024 - board_mux_setup(); -#endif - return 0; -} - -void fdt_fixup_spi_mux(void *blob) -{ - int nodeoff = 0; - - if (hwconfig_arg_cmp("pin_mux", "tdm")) { - while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, - "eon,en25s64")) >= 0) { - fdt_del_node(blob, nodeoff); - } - } else { - /* remove tdm node */ - while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, - "maxim,ds26522")) >= 0) { - fdt_del_node(blob, nodeoff); - } - } -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = env_get_bootm_low(); - size = env_get_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#ifdef CONFIG_PCI - pci_of_setup(blob, bd); -#endif - - fdt_fixup_liodn(blob); - -#ifdef CONFIG_HAS_FSL_DR_USB - fsl_fdt_fixup_dr_usb(blob, bd); -#endif - -#ifdef CONFIG_SYS_DPAA_FMAN - fdt_fixup_fman_ethernet(blob); - fdt_fixup_board_enet(blob); -#endif - fdt_fixup_spi_mux(blob); - - return 0; -} - -void qixis_dump_switch(void) -{ - int i, nr_of_cfgsw; - - QIXIS_WRITE(cms[0], 0x00); - nr_of_cfgsw = QIXIS_READ(cms[1]); - - puts("DIP switch settings dump:\n"); - for (i = 1; i <= nr_of_cfgsw; i++) { - QIXIS_WRITE(cms[0], i); - printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); - } -} diff --git a/board/freescale/t102xqds/t102xqds.h b/board/freescale/t102xqds/t102xqds.h deleted file mode 100644 index d327b5edb9..0000000000 --- a/board/freescale/t102xqds/t102xqds.h +++ /dev/null @@ -1,14 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -#ifndef __T102x_QDS_H__ -#define __T102x_QDS_H__ - -void fdt_fixup_board_enet(void *blob); -void pci_of_setup(void *blob, bd_t *bd); -int select_i2c_ch_pca9547(u8 ch, int bus_num); - -#endif diff --git a/board/freescale/t102xqds/t102xqds_qixis.h b/board/freescale/t102xqds/t102xqds_qixis.h deleted file mode 100644 index b84a33fc48..0000000000 --- a/board/freescale/t102xqds/t102xqds_qixis.h +++ /dev/null @@ -1,63 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#ifndef __T1024QDS_QIXIS_H__ -#define __T1024QDS_QIXIS_H__ - -/* Definitions of QIXIS Registers for T1024/T1023 QDS */ - -/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ -#define BRDCFG4_EMISEL_MASK 0xE0 -#define BRDCFG4_EMISEL_SHIFT 5 - -/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/ -#define BRDCFG5_IMX_MASK 0xC0 -#define BRDCFG5_IMX_DIU 0x80 - -#define BRDCFG5_SPIRTE_MASK 0x07 -#define BRDCFG5_SPIRTE_TDM 0x01 -#define BRDCFG5_SPIRTE_SDHC 0x02 -#define BRDCFG9_XFI_TX_DISABLE 0x10 - -/* BRDCFG13[0:5] TDM configuration and setup */ -#define BRDCFG13_TDM_MASK 0xfc -#define BRDCFG13_TDM_INTERFACE 0x37 -#define BRDCFG13_HDLC_LOOPBACK 0x29 -#define BRDCFG13_TDM_LOOPBACK 0x31 - -/* BRDCFG15[3] controls LCD Panel Powerdown */ -#define BRDCFG15_LCDFM 0x20 -#define BRDCFG15_LCDPD 0x10 -#define BRDCFG15_LCDPD_MASK 0x10 -#define BRDCFG15_LCDPD_ENABLED 0x00 - -/* BRDCFG15[6:7] controls DIU MUX selction*/ -#define BRDCFG15_DIUSEL_MASK 0x03 -#define BRDCFG15_DIUSEL_HDMI 0x00 -#define BRDCFG15_DIUSEL_LCD 0x01 -#define BRDCFG15_DIUSEL_UCC 0x02 -#define BRDCFG15_DIUSEL_TDM 0x03 - -/* SYSCLK */ -#define QIXIS_SYSCLK_66 0x0 -#define QIXIS_SYSCLK_83 0x1 -#define QIXIS_SYSCLK_100 0x2 -#define QIXIS_SYSCLK_125 0x3 -#define QIXIS_SYSCLK_133 0x4 -#define QIXIS_SYSCLK_150 0x5 -#define QIXIS_SYSCLK_160 0x6 -#define QIXIS_SYSCLK_166 0x7 -#define QIXIS_SYSCLK_64 0x8 - -/* DDRCLK */ -#define QIXIS_DDRCLK_66 0x0 -#define QIXIS_DDRCLK_100 0x1 -#define QIXIS_DDRCLK_125 0x2 -#define QIXIS_DDRCLK_133 0x3 - - -#define QIXIS_SRDS1CLK_122 0x5a -#define QIXIS_SRDS1CLK_125 0x5e -#endif diff --git a/board/freescale/t102xqds/tlb.c b/board/freescale/t102xqds/tlb.c deleted file mode 100644 index 3546331aab..0000000000 --- a/board/freescale/t102xqds/tlb.c +++ /dev/null @@ -1,116 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, - CONFIG_SYS_INIT_RAM_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* TLB 1 */ - /* *I*** - Covers boot page */ -#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) - /* - * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the - * SRAM is at 0xfffc0000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_256K, 1), -#else - SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), -#endif - - /* *I*G* - CCSRBAR */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_16M, 1), - - /* *I*G* - Flash, localbus */ - /* This will be changed to *I*G* after relocation to RAM. */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - -#ifndef CONFIG_SPL_BUILD - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_1G, 1), - - /* *I*G* - PCI I/O */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256K, 1), - - /* Bman/Qman */ -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 5, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 6, BOOKE_PAGESZ_16M, 1), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 7, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 8, BOOKE_PAGESZ_16M, 1), -#endif -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 9, BOOKE_PAGESZ_4M, 1), -#endif -#ifdef CONFIG_SYS_NAND_BASE - SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 10, BOOKE_PAGESZ_64K, 1), -#endif -#ifdef QIXIS_BASE - SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 11, BOOKE_PAGESZ_4K, 1), -#endif - -#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 12, BOOKE_PAGESZ_1G, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, - CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 13, BOOKE_PAGESZ_1G, 1) -#endif - /* entry 14 and 15 has been used hard coded, they will be disabled - * in cpu_init_f, so if needed more, will use entry 16 later. - */ -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig b/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig deleted file mode 100644 index 2199abcb95..0000000000 --- a/configs/T1024QDS_DDR4_SECURE_BOOT_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_DDR4_defconfig b/configs/T1024QDS_DDR4_defconfig deleted file mode 100644 index 0a52af48bb..0000000000 --- a/configs/T1024QDS_DDR4_defconfig +++ /dev/null @@ -1,64 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_NAND_defconfig b/configs/T1024QDS_NAND_defconfig deleted file mode 100644 index 9db39b1b58..0000000000 --- a/configs/T1024QDS_NAND_defconfig +++ /dev/null @@ -1,83 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x140000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_ENV_IS_IN_NAND=y -CONFIG_FSL_CAAM=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_SDCARD_defconfig b/configs/T1024QDS_SDCARD_defconfig deleted file mode 100644 index 679f2ad208..0000000000 --- a/configs/T1024QDS_SDCARD_defconfig +++ /dev/null @@ -1,80 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_SPL_MMC_SUPPORT=y -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD" -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_MMC_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_ENV_IS_IN_MMC=y -CONFIG_FSL_CAAM=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_SECURE_BOOT_defconfig b/configs/T1024QDS_SECURE_BOOT_defconfig deleted file mode 100644 index cc080c7285..0000000000 --- a/configs/T1024QDS_SECURE_BOOT_defconfig +++ /dev/null @@ -1,70 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_SPIFLASH_defconfig b/configs/T1024QDS_SPIFLASH_defconfig deleted file mode 100644 index 01bc5111e0..0000000000 --- a/configs/T1024QDS_SPIFLASH_defconfig +++ /dev/null @@ -1,83 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH" -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_SPI_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_ENV_ADDR=0xFFFC9000 -CONFIG_FSL_CAAM=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T1024QDS_defconfig b/configs/T1024QDS_defconfig deleted file mode 100644 index 6ebffb8dd1..0000000000 --- a/configs/T1024QDS_defconfig +++ /dev/null @@ -1,67 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T1024QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_SILENT_CONSOLE=y -# CONFIG_CONSOLE_MUX is not set -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)" -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_FLASH_CFI_MTD=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h deleted file mode 100644 index 53ae961837..0000000000 --- a/include/configs/T102xQDS.h +++ /dev/null @@ -1,756 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2014 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -/* - * T1024/T1023 QDS board configuration file - */ - -#ifndef __T1024QDS_H -#define __T1024QDS_H - -#include - -/* High Level Configuration Options */ -#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ -#define CONFIG_ENABLE_36BIT_PHYS - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP 1 -#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ -#endif - -#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ -#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS - -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_DEEP_SLEEP - -#ifdef CONFIG_RAMBOOT_PBL -#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_PAD_TO 0x40000 -#define CONFIG_SPL_MAX_SIZE 0x28000 -#define RESET_VECTOR_OFFSET 0x27FFC -#define BOOT_PAGE_OFFSET 0x27000 -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_SKIP_RELOCATE -#define CONFIG_SPL_COMMON_INIT_DDR -#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE -#endif - -#ifdef CONFIG_MTD_RAW_NAND -#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_nand_rcw.cfg -#endif - -#ifdef CONFIG_SPIFLASH -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC -#define CONFIG_SPL_SPI_FLASH_MINIMAL -#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#endif -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_spi_rcw.cfg -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC -#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) -#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#endif -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_sd_rcw.cfg -#endif - -#endif /* CONFIG_RAMBOOT_PBL */ - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -/* PCIe Boot - Master */ -#define CONFIG_SRIO_PCIE_BOOT_MASTER -/* - * for slave u-boot IMAGE instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull -#else -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000 -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000 -#endif -/* - * for slave UCODE and ENV instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull -#else -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000 -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000 -#endif -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ -/* slave core release by master*/ -#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 -#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ - -/* PCIe Boot - Slave */ -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) -/* Set 1M boot space for PCIe boot */ -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#endif - -#if defined(CONFIG_SPIFLASH) -#elif defined(CONFIG_SDCARD) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -#ifndef __ASSEMBLY__ -unsigned long get_board_sys_clk(void); -unsigned long get_board_ddr_clk(void); -#endif - -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_SYS_CACHE_STASHING -#define CONFIG_BACKSIDE_L2_CACHE -#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_DDR_ECC -#ifdef CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef -#endif - -/* - * Config the L3 Cache as L3 SRAM - */ -#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 -#define CONFIG_SYS_L3_SIZE (256 << 10) -#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) -#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) -#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_DCSRBAR 0xf0000000 -#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull -#endif - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_SYS_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 - -/* - * DDR Setup - */ -#define CONFIG_VERY_BIG_RAM -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) -#define CONFIG_DDR_SPD - -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS 0x51 - -#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ - -/* - * IFC Definitions - */ -#define CONFIG_SYS_FLASH_BASE 0xe0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) -#else -#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE -#endif - -#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) -/* NOR Flash Timing Params */ -#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 -#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ - FTIM0_NOR_TEADC(0x5) | \ - FTIM0_NOR_TEAHC(0x5)) -#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ - FTIM1_NOR_TRAD_NOR(0x1A) |\ - FTIM1_NOR_TSEQRAD_NOR(0x13)) -#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ - FTIM2_NOR_TCH(0x4) | \ - FTIM2_NOR_TWPH(0x0E) | \ - FTIM2_NOR_TWP(0x1c)) -#define CONFIG_SYS_NOR_FTIM3 0x0 - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} -#define CONFIG_FSL_QIXIS /* use common QIXIS code */ -#define QIXIS_BASE 0xffdf0000 -#ifdef CONFIG_PHYS_64BIT -#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) -#else -#define QIXIS_BASE_PHYS QIXIS_BASE -#endif -#define QIXIS_LBMAP_SWITCH 0x06 -#define QIXIS_LBMAP_MASK 0x0f -#define QIXIS_LBMAP_SHIFT 0 -#define QIXIS_LBMAP_DFLTBANK 0x00 -#define QIXIS_LBMAP_ALTBANK 0x04 -#define QIXIS_RST_CTL_RESET 0x31 -#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 -#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 -#define QIXIS_RST_FORCE_MEM 0x01 - -#define CONFIG_SYS_CSPR3_EXT (0xf) -#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 \ - | CSPR_MSEL_GPCM \ - | CSPR_V) -#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) -#define CONFIG_SYS_CSOR3 0x0 -/* QIXIS Timing parameters for IFC CS3 */ -#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ - FTIM0_GPCM_TEADC(0x0e) | \ - FTIM0_GPCM_TEAHC(0x0e)) -#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ - FTIM1_GPCM_TRAD(0x3f)) -#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ - FTIM2_GPCM_TCH(0x8) | \ - FTIM2_GPCM_TWP(0x1f)) -#define CONFIG_SYS_CS3_FTIM3 0x0 - -#define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_NAND_BASE 0xff800000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) -#else -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE -#endif -#define CONFIG_SYS_NAND_CSPR_EXT (0xf) -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ - | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* ONFI NAND Flash mode0 Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ - FTIM0_NAND_TWP(0x18) | \ - FTIM0_NAND_TWCHT(0x07) | \ - FTIM0_NAND_TWH(0x0a)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ - FTIM1_NAND_TWBE(0x39) | \ - FTIM1_NAND_TRR(0x0e) | \ - FTIM1_NAND_TRP(0x18)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ - FTIM2_NAND_TREH(0x0a) | \ - FTIM2_NAND_TWHRE(0x1e)) -#define CONFIG_SYS_NAND_FTIM3 0x0 - -#define CONFIG_SYS_NAND_DDR_LAW 11 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) - -#if defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 -#else -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 -#endif - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#endif - -#if defined(CONFIG_RAMBOOT_PBL) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_HWCONFIG - -/* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 -/* The assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#else -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) - -/* Serial Port */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) -#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) -#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) - -/* Video */ -#ifdef CONFIG_ARCH_T1024 /* no DIU on T1023 */ -#define CONFIG_FSL_DIU_FB -#ifdef CONFIG_FSL_DIU_FB -#define CONFIG_FSL_DIU_CH7301 -#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000) -#define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_BMP_LOGO -#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS -/* - * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so - * disable empty flash sector detection, which is I/O-intensive. - */ -#undef CONFIG_SYS_FLASH_EMPTY_INFO -#endif -#endif - -/* I2C */ -#ifndef CONFIG_DM_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */ -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */ -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 -#else -#define CONFIG_I2C_SET_DEFAULT_BUS_NUM -#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 -#endif - -#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ - -#define I2C_MUX_PCA_ADDR 0x77 -#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ -#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ -#define I2C_RETIMER_ADDR 0x18 - -/* I2C bus multiplexer */ -#define I2C_MUX_CH_DEFAULT 0x8 -#define I2C_MUX_CH_DIU 0xC -#define I2C_MUX_CH5 0xD -#define I2C_MUX_CH7 0xF - -/* LDI/DVI Encoder for display */ -#define CONFIG_SYS_I2C_LDI_ADDR 0x38 -#define CONFIG_SYS_I2C_DVI_ADDR 0x75 -#define CONFIG_SYS_I2C_DVI_BUS_NUM 0 - -/* - * RTC configuration - */ -#define RTC -#define CONFIG_RTC_DS3231 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * eSPI - Enhanced SPI - */ - -/* - * General PCIe - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_PCIE1 /* PCIE controller 1 */ -#define CONFIG_PCIE2 /* PCIE controller 2 */ -#define CONFIG_PCIE3 /* PCIE controller 3 */ -#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ -#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ -#define CONFIG_PCI_INDIRECT_BRIDGE - -#ifdef CONFIG_PCI -/* controller 1, direct to uli, tgtid 3, Base address 20000 */ -#ifdef CONFIG_PCIE1 -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull -#else -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 -#endif -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull -#else -#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 -#endif -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ -#endif - -/* controller 2, Slot 2, tgtid 2, Base address 201000 */ -#ifdef CONFIG_PCIE2 -#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull -#else -#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0x90000000 -#endif -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull -#else -#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 -#endif -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ -#endif - -/* controller 3, Slot 1, tgtid 1, Base address 202000 */ -#ifdef CONFIG_PCIE3 -#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull -#else -#define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000 -#endif -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull -#else -#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 -#endif -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#endif /* CONFIG_PCI */ - -/* - *SATA - */ -#define CONFIG_FSL_SATA_V2 -#ifdef CONFIG_FSL_SATA_V2 -#define CONFIG_SYS_SATA_MAX_DEVICE 1 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_LBA48 -#endif - -/* - * USB - */ -#define CONFIG_HAS_FSL_DR_USB - -#ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#endif - -/* - * SDHC - */ -#ifdef CONFIG_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#endif - -/* Qman/Bman */ -#ifndef CONFIG_NOBQFMAN -#define CONFIG_SYS_BMAN_NUM_PORTALS 10 -#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull -#else -#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE -#endif -#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE -#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ - CONFIG_SYS_BMAN_CENA_SIZE) -#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 -#define CONFIG_SYS_QMAN_NUM_PORTALS 10 -#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull -#else -#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE -#endif -#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE -#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ - CONFIG_SYS_QMAN_CENA_SIZE) -#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 - -#define CONFIG_SYS_DPAA_FMAN - -/* Default address of microcode for the Linux FMan driver */ -#if defined(CONFIG_SPIFLASH) -/* - * env is stored at 0x100000, sector size is 0x10000, ucode is stored after - * env, so we got 0x110000. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0x110000 -#define CONFIG_SYS_QE_FW_ADDR 0x130000 -#elif defined(CONFIG_SDCARD) -/* - * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is - * about 1MB (2048 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820). - */ -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) -#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920) -#elif defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) -#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) -/* - * Slave has no ucode locally, it can fetch this from remote. When implementing - * in two corenet boards, slave's ucode could be stored in master's memory - * space, the address can be mapped from slave TLB->slave LAW-> - * slave SRIO or PCIE outbound window->master inbound window-> - * master LAW->the ucode address in master's memory space. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 -#else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 -#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000 -#endif -#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) -#endif /* CONFIG_NOBQFMAN */ - -#ifdef CONFIG_SYS_DPAA_FMAN -#define RGMII_PHY1_ADDR 0x1 -#define RGMII_PHY2_ADDR 0x2 -#define SGMII_CARD_AQ_PHY_ADDR_S3 0x3 -#define SGMII_CARD_AQ_PHY_ADDR_S4 0x4 -#define SGMII_CARD_AQ_PHY_ADDR_S5 0x5 -#define SGMII_CARD_PORT1_PHY_ADDR 0x1C -#define SGMII_CARD_PORT2_PHY_ADDR 0x1D -#define SGMII_CARD_PORT3_PHY_ADDR 0x1E -#define SGMII_CARD_PORT4_PHY_ADDR 0x1F -#endif - -#ifdef CONFIG_FMAN_ENET -#define CONFIG_ETHPRIME "FM1 at DTSEC4" -#endif - -/* - * Dynamic MTD Partition support with mtdparts - */ - -/* - * Environment - */ -#define CONFIG_LOADS_ECHO /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ -#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */ -#define __USB_PHY_TYPE utmi - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ - "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \ - "ramdiskfile=t1024qds/ramdisk.uboot\0" \ - "fdtfile=t1024qds/t1024qds.dtb\0" \ - "netdev=eth0\0" \ - "video-mode=fslfb:1024x768-32 at 60,monitor=dvi\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot && " \ - "protect off $ubootaddr +$filesize && " \ - "erase $ubootaddr +$filesize && " \ - "cp.b $loadaddr $ubootaddr $filesize && " \ - "protect on $ubootaddr +$filesize && " \ - "cmp.b $loadaddr $ubootaddr $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "fdtaddr=d00000\0" \ - "bdev=sda3\0" - -#define CONFIG_LINUX \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "setenv ramdiskaddr 0x02000000;" \ - "setenv fdtaddr 0x00c00000;" \ - "setenv loadaddr 0x1000000;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_LINUX - -#include - -#endif /* __T1024QDS_H */