From patchwork Thu Jul 2 08:02:26 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Faiz Abbas X-Patchwork-Id: 240594 List-Id: U-Boot discussion From: faiz_abbas at ti.com (Faiz Abbas) Date: Thu, 2 Jul 2020 13:32:26 +0530 Subject: [PATCH 06/13] arm: mach-k3: am6_init: Do USB fixups to facilitate host and device boot modes In-Reply-To: <20200702080233.27582-1-faiz_abbas@ti.com> References: <20200702080233.27582-1-faiz_abbas@ti.com> Message-ID: <20200702080233.27582-7-faiz_abbas@ti.com> U-boot only supports either USB host or device mode for a node at a time in dts To support both host and dfu bootmodes, set "peripheral" as the default dr_mode but fixup property to "host" if host bootmode is detected This needs to happen before the dwc3 generic layer binds the usb device to a host or device driver. Therefore, open code the configurations in spl_early_init() and add the fixup after the fdtdec_setup() and before the dm_init_scan() Also use the same fixup function to set the USB-PCIe Serdes mux to PCIe in both the host and device cases. This is required for accessing the interface at USB 2.0 speeds Signed-off-by: Faiz Abbas --- arch/arm/mach-k3/am6_init.c | 68 +++++++++++++++++++++++++++++++++++-- 1 file changed, 66 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-k3/am6_init.c b/arch/arm/mach-k3/am6_init.c index 42d13a39f8..b65860fef3 100644 --- a/arch/arm/mach-k3/am6_init.c +++ b/arch/arm/mach-k3/am6_init.c @@ -7,6 +7,7 @@ */ #include +#include #include #include #include @@ -17,11 +18,15 @@ #include #include #include +#include +#include #include #include #include #include +DECLARE_GLOBAL_DATA_PTR; + #ifdef CONFIG_SPL_BUILD #ifdef CONFIG_K3_LOAD_SYSFW #ifdef CONFIG_TI_SECURE_DEVICE @@ -119,7 +124,67 @@ void k3_mmc_restart_clock(void) void k3_mmc_stop_clock(void) {} void k3_mmc_restart_clock(void) {} #endif +#if CONFIG_IS_ENABLED(DFU) || CONFIG_IS_ENABLED(USB_STORAGE) +#define CTRLMMR_SERDES0_CTRL 0x00104080 +#define PCIE_LANE0 0x1 +void fixup_usb_boot(void) +{ + int ret; + switch (spl_boot_device()) { + case BOOT_DEVICE_USB: + /* + * If bootmode is Host bootmode, fixup the dr_mode to host + * before the dwc3 bind takes place + */ + ret = fdt_find_and_setprop((void *)gd->fdt_blob, + "/interconnect at 100000/dwc3 at 4000000/usb at 10000", + "dr_mode", "host", 11, 0); + if (ret) + printf("%s: fdt_find_and_setprop() failed:%d\n", __func__, + ret); + /* fallthrough */ + case BOOT_DEVICE_DFU: + /* + * The serdes mux between PCIe and USB3 needs to be set to PCIe for + * accessing the interface at USB 2.0 + */ + writel(PCIE_LANE0, CTRLMMR_SERDES0_CTRL); + default: + ; + } +} +#endif +int am6_spl_early_init(void) +{ + int ret; +#if CONFIG_VAL(SYS_MALLOC_F_LEN) +#ifdef CONFIG_MALLOC_F_ADDR + gd->malloc_base = CONFIG_MALLOC_F_ADDR; +#endif + gd->malloc_limit = CONFIG_VAL(SYS_MALLOC_F_LEN); + gd->malloc_ptr = 0; +#endif + ret = fdtdec_setup(); + if (ret) { + printf("fdtdec_setup() returned error %d\n", ret); + return ret; + } + +#if CONFIG_IS_ENABLED(DFU) || CONFIG_IS_ENABLED(USB_STORAGE) + fixup_usb_boot(); +#endif + /* With CONFIG_SPL_OF_PLATDATA, bring in all devices */ + ret = dm_init_and_scan(!CONFIG_IS_ENABLED(OF_PLATDATA)); + if (ret) { + printf("dm_init_and_scan() returned error %d\n", ret); + return ret; + } + + gd->flags |= GD_FLG_SPL_EARLY_INIT; + + return 0; +} void board_init_f(ulong dummy) { #if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM654_DDRSS) @@ -141,9 +206,8 @@ void board_init_f(ulong dummy) disable_linefill_optimization(); setup_k3_mpu_regions(); #endif - /* Init DM early in-order to invoke system controller */ - spl_early_init(); + am6_spl_early_init(); #ifdef CONFIG_K3_EARLY_CONS /*